[ovirt-users] Re: poweroff and reboot with ovirt_vm ansible module

hi, AFAIK, setting state=stopped is the only way to poweroff a VM. While to reboot a VM, you could also follow the steps below: 1. Update a VM with some new properties that requires a restart operation, also with the param: next_run=true 2. Set state=next_run in your playbook and apply it Then

[ovirt-users] Re: iSCSI Boot from SAN

On Fri, 2 Nov 2018, 20:31 Alan G I'm setting up a lab with oVirt 4.2. All hosts are disk-less and boot from > a NetApp using iSCSI. All storage domains are also iSCSI, to the same > NetApp as BFS. > > Whenever I put a host into maintenance vdsm seems to try to un-mount all > iSCSI partitions

[ovirt-users] Re: ovirt-engine-extension-aaa-ldap-setup failed

The backend is 389 DS, no this is not Govt related. This will be used as a training platform for my local ISSA chapter. This is a new 389 DS server. I followed the instructions at https://www.unixmen.com/install-and-configure-ldap-server-in-centos-7/ The server is "stock" with the exceptions

[ovirt-users] Re: Best Practice for Controller Backup

Hi, I'm run host engine as KVM appliance on our file server (SuSE Linux). KVM appliance is very easy to back up, use snapshot or even better clone. On 11/1/18 3:19 PM, David Johnson wrote: Is there a best practice for configuring a secondary ovirt engine to take over in case of engine

[ovirt-users] iSCSI Boot from SAN

Hi, I'm setting up a lab with oVirt 4.2. All hosts are disk-less and boot from a NetApp using iSCSI. All storage domains are also iSCSI, to the same NetApp as BFS. Whenever I put a host into maintenance vdsm seems to try to un-mount all iSCSI partitions including the OS partition, causing the

[ovirt-users] poweroff and reboot with ovirt_vm ansible module

Hello, is there a way to poweroff or reboot (without stopped and running state) a vm with the ovirt_vm ansible module? -- Nathanaël Blanchet Supervision réseau Pôle Infrastrutures Informatiques 227 avenue Professeur-Jean-Louis-Viala 34193 MONTPELLIER CEDEX 5 Tél. 33 (0)4 67 54 84 55 Fax

[ovirt-users] Re: Networking - How to pass all vlan (trunk) to a guest VM?

Hi Edy, Here is the output requested. Note that I attached the logical network named "trunk" below to a VM. From that VM, I do have enable the 8021q module and configure sub-interface. But I don't see any traffic coming in. [root@c200m2-1 ~]# ip addr 1: lo: mtu 65536 qdisc noqueue state

[ovirt-users] Re: oVirt deployment with GlusterFS with replica 3 arbiter 1

For anyone who stumbles upon this - I have managed to test this setup with VMs under KVM. It seems that all 3 systems need to be oVirt Nodes, while my 3rd node has 1 CPU and 1GB of RAM with 20GB of local storage - so most probably this setup is doable. Still I need to test the HA once the host

[ovirt-users] Re: ovirt-engine-extension-aaa-ldap-setup failed

Is binding allowed in your 389ds instance? On Fri, Nov 2, 2018, 8:11 AM Jeremy Tourville The backend is 389 DS, no this is not Govt related. This will be used as > a training platform for my local ISSA chapter. This is a new 389 DS > server. I followed the instructions at >

[ovirt-users] [ANN] oVirt 4.2.7 is now generally available

The oVirt Project is pleased to announce the general availability of oVirt 4.2.7, as of November 2nd, 2018. This update is the seventh in a series of stabilization updates to the 4.2 series. This release is available now for: * Red Hat Enterprise Linux 7.5 or later (7.6 recommended) * CentOS