I saw something like this also.
The new ansible based installation tries to verify hostnames using the
getent command
with something like...
getent ahostsv4 hostname.domain | grep hostname.domain
In my case that failed to pickup a cname I wanted to use, even though
nslookup hostname.domain
Is your CPU really nehalem or is it something newer?
cat /proc/cpuinfo and google the model if you're not sure.
For my E5650 servers I found I had to go into the BIOS and enable some AES
instruction
before the oVirt node (actually libvirt) detected the CPU type as newer
than Nehalem.
On Tue,
I'm not sure where to send a request for including the current Aquantia 107
(10GbaseT nic) driver to be included in the ovirt-node-ng image. I don't
see a centos RPM for kmod-redhat-atlantic, apparently there's a scientific
linux rpm available for download.
.
On Fri, Aug 31, 2018 at 10:52 AM carl langlois
wrote:
> most of my cpu are
> Intel(R) Xeon(R) CPU E5-1650 v3 @ 3.50GHz
>
> so yes it is newer..Not sure how to resolve this.
>
> On Tue, Aug 28, 2018 at 2:29 PM Edward Berger wrote:
>
>> Is your CPU really nehalem or is
If you haven't "installed" or "reinstalled" the second host without
purposely selecting "DEPLOY" under hosted-engine actions,
it will not be able to run the hosted-engine VM.
A quick way to tell if you did is to look at the hosts view and look for
the "crowns" on the left like this attached pic
OK, if the icon is there that is a good thing. There would be no icon if
you didn't select deploy.
Its not terribly obvious when first installing a second host that it needs
the deploy part set.
There's something else causing the engine migration to fail. You can dig
through the logs on the
That is completely normal if you didn't download and install the CA
certificate from your ovirt engine GUI.
There's a download link for it on the page before you login?
On Mon, Mar 18, 2019 at 5:01 PM wrote:
> Hi,
>
> I tried to create windows2012 vm on nfs data domain, but the disk was
>
When trying to put a node 4.3.0 into maintenance, I get the following error:
--
Error while executing action: Cannot switch Host winterfell.psc.edu to
Maintenance mode. Image transfer is in progress for the following (2) disks:
8d130846-bd84-46b0-9a45-b6a2ecf66865,
I upgraded some nodes from 4.28 to 4.3 and now when I look at the cockpit
"services"
tab I see a red failure for Gluster Events Notifier and clicking through I
get these messages below.
14:00
glustereventsd.service failed.
systemd
14:00
Unit glustereventsd.service entered failed state.
systemd
I'm wondering what cluster cpu compatibility version the Ryzen 2700 would
go under?
It used to default to Opteron G3 when I tried it before, which is now
"unsupported" as of ovirt 4.3.
CentOS 7 complains about "untested" CPU with Ryzen 2700 in my experience.
Maybe Fedora is better there.
Here are
at you mentioned).
>
>
>
> On Fri, Feb 8, 2019 at 9:26 PM Edward Berger wrote:
>
>> I'm wondering what cluster cpu compatibility version the Ryzen 2700 would
>> go under?
>> It used to default to Opteron G3 when I tried it before, which is now
>> "unsuppo
ls -l /rhev/data-center/mnt/glusterSD/*/*/images/*
# any under "engine volume" that are owned by root chown and chmod as
vdsm:kvm 660
# then engine should be able to start.
On Tue, Feb 12, 2019 at 4:43 PM Endre Karlson
wrote:
> I Also tried to run
> service vdsmd stop
> vdsm-tool configure
A coworker and I are trying to bring up some nvidia vGPU VMs on ovirt 4.3,
but are experiencing issues with the remote consoles for both Windows and
Linux.
A windows10 VM for example works OK with a windows remote desktop client
after enabling the service inside the VM, but using the oVirt VM
If its a node-ng install, you should just update the whole image with
yum update ovirt-node-ng-image-update
On Wed, Feb 13, 2019 at 8:12 PM Vincent Royer wrote:
> Sorry, this is a node install w/ he.
>
> On Wed, Feb 13, 2019, 4:44 PM Vincent Royer
>> trying to update from 4.2.6 to 4.2.8
>>
>>
We are attempting to get vGPU-enabled guests working with our oVirt 4.3.0
configuration, but have run into problems.
We are running:
NVidia License Server version 2018.09
NVidia License Client Manager 2018.10.0.25098346
and that license info is correctly retrieved by the clients.
With a
I don't believe the wizard followed your wishes if it comes up with 1005gb
for the thinpool.
500gb data + 500gb vmstore +5gb metadata = 1005gb
The wizard tries to do the same setup on all three gluster hosts.
So if you change anything, you have to "check and edit" the config file it
generates in
:
> On Thu, Feb 7, 2019 at 8:57 AM Edward Berger wrote:
> >
> > I'm seeing migration failures for the hosted-engine VM from a 4.28 node
> to a 4.30 node so I can complete the node upgrades.
>
> You may be running into
> https://bugzilla.redhat.com/show_bug.cg
I'm seeing migration failures for the hosted-engine VM from a 4.28 node to
a 4.30 node so I can complete the node upgrades.
In one case I tried to force an update on the last node and now have a
cluster where the hosted-engine VM fails to start properly. Sometimes
something thinks the VM is
Ok, I'll check.
4.2.8 nodes
libvirt.x86_644.5.0-10.el7_6.3
installed
4.3.0 upgraded nodes
libvirt.x86_644.5.0-10.el7_6.4
installed
On Thu, Feb 7, 2019 at 12:03 AM Sahina Bose wrote:
> On Thu, Feb 7, 2019 at 8:57 AM Edward Berger wrote:
> >
19 at 7:31 AM Edward Berger wrote:
> >
> > I have a problem host which also is the one I deployed a hyperconverged
> oVirt node-ng cluster from with the cockpit's hyperconverged installation
> wizard.
> >
> > When I realized after deploying that I hadn't set the MTUs corre
, and now it looks it seems to freeze when I try
to reinstall with engine deploy... It eventually times out with a failure.
On Sun, Jan 27, 2019 at 8:59 PM Edward Berger wrote:
> I have a problem host which also is the one I deployed a hyperconverged
> oVirt node-ng cluster from with the
Jan 29, 2019 at 10:05 PM Edward Berger
> wrote:
> >
> > Done. It still won't let me remove the host.
> > clicked maintenance, checked ignore gluster... box.
> > clicked remove. got popup " track00.yard.psc.edu:
> >
> > Cannot remove Host. Server havin
ven't been able to get any response from devs on any of (the myriad) of
>> issues with the 4.2.8 image.
>> Also having a ton of strange issues with the hosted-engine vm deployment.
>>
>> On Mon, Feb 4, 2019 at 11:59 AM Edward Berger
>> wrote:
>>
>>>
Yes, I had that issue with an 4.2.8 installation.
I had to manually edit the "web-UI-generated" config to be anywhere close
to what I wanted.
I'll attach an edited config as an example.
On Mon, Feb 4, 2019 at 2:51 PM feral wrote:
> New install of ovirt-node 4.2 (from iso). Setup each node with
Hi,
One of our projects wants to try offering VMs with nvidia vGPU.
My co-worker had some problems before, so I thought I'd try the latest 4.3
ovirt-node-ng.
In the "Edit Host" -> kernel dialog I see two promising checkbox options
Hostdev Passthrough & SR-IOV (which adds to kernel line
> TASK [openshift_control_plane : Wait for control plane pods to appear]
*
> Monday 27 May 2019 13:31:54 + (0:00:00.180) 0:14:33.857
> FAILED - RETRYING: Wait for control plane pods to appear (60 retries
left).
> FAILED - RETRYING: Wait for control plane pods to
When I read your intro, and I hit the memory figure, I was saying to
myself, what
I'd definitely increase the memory if possible. As high as you can
affordably fit into the servers.
Engine asks 16GB at installation time, add some for gluster services and
you're at your limits before you add
I'll presume you didn't fully backup your hosts root file systems on the
host which was fried.
It may be easier to replace with a new hostname/IP.
I would focus on the gluster config first, since it was hyperconverged.
I don't know which way engine UI is using to detect gluster mount on
missing
I'm trying to bring up a single node hyperconverged with the current
node-ng ISO installation,
but it ends with this failure message.
TASK [gluster.features/roles/gluster_hci : Check if /var/log has enough
disk space] ***
fatal: [br014.bridges.psc.edu]: FAILED! => {"changed": true, "cmd": "df -m
step before deployment and adding
> gluster_features_force_varlogsizecheck:
> false under the vars section of the file.
>
> Regards
> Parth Dhanjal
>
> On Fri, May 10, 2019 at 5:58 AM Edward Berger wrote:
>
>> I'm trying to bring up a single node hyperconverged with the current
>&g
You might be hitting a multipath config issue.
On a 4.3.4. node-ng cluster I had a similar problem. spare disk was on
/dev/sda (boot disk was /dev/sdb)
I found this link
https://stackoverflow.com/questions/45889799/pvcreate-failing-to-create-pv-device-not-found-dev-sdxy-or-ignored-by-filteri
NFO 2019-04-25 16:36:24,874 server:45:server:(start) Starting
(pid=56989, version=1.5.1)
(MainThread) INFO 2019-04-25 16:36:24,879 image_proxy:34:root:(main) Server
started, successfully notified systemd
On Tue, Apr 23, 2019 at 4:51 PM Edward Berger wrote:
> Previously I had issues with the up
Thanks! That fixed the problem. engine-setup was able to complete.
On Wed, Apr 17, 2019 at 3:48 AM Yedidyah Bar David wrote:
> On Wed, Apr 17, 2019 at 10:30 AM Lucie Leistnerova
> wrote:
> >
> > Hi Edward,
> >
> > On 4/16/19 9:23 PM, Edward Berger wrote:
&
Previously I had issues with the upgrades to 4.3.3 failing because of
"stale" image transfer data, so I removed it from the database using the
info given here on the mailing list and was able to complete the oVirt node
and engine upgrades.
Now I have a new problem. I can't upload a disk image
Maybe there is something already on the disk from before?
gluster setup wants it completely blank, no detectable filesystem, no raid,
etc.
see what is there with fdisk.-l see what PVs exist with pvs.
Manually wipe, reboot and try again?
On Fri, Jun 28, 2019 at 5:37 AM wrote:
> I have added the
If you installed your hypervisor hosts from the Node installer iso, updates
are done by
yum update ovirt-node-ng-image-update, and then reboot the host.
On the hosted-engine VM you run the yum update the "release" and *setup*
as you were trying on the node.
On Sun, Aug 11, 2019 at 8:41 PM
on oVirt node ng, repos are usually disabled, so you need to enable the
repo to install other RPMs.
yum --enablerepo=base install dump xfsdump
yum --enablerepo=base install pam_krb5
On Wed, Aug 14, 2019 at 8:53 PM wrote:
> Hello all,
>
> Hope everyone is doing well! I would simply like to
I had a similar issue, my LDAP guy said oVirt engine was asking for
uidObject which our ldap didn't provide and
gave me this config addition to make to the
/etc/ovirt-engine/aaa/MY.DOMAIN.properties file so it would
use inetOrgPerson instead
# override default ldap filter. defaults found at
#
You can change that anytime.
On the engine GUI, set the host to maintenance,
The select the "Installation/Reinstall" menu item.
Select the "Hosted Engine" tab, and then pick "DEPLOY"
[image: host-deploy.JPG]
On Wed, Sep 18, 2019 at 6:14 AM wrote:
> I tryed to add a new host to my oVirt
vdsm creates persistant network configs that overwrite manual changes at
reboot
in /var/lib/vdsm/persistence/netconf
You can check your other hosts for any differences there.
It is recommended that networks are set up and managed through ovirt engine.
On Sun, Sep 22, 2019 at 6:01 AM TomK
I thought that was it.
I remembered some experience I had with a test install that recommended
turning the network filter off.
You probably already did this, but when you turn off filtering or make
other changes
to the logical network like MTU size you must completely shutdown the
attached VMs
Does your network vnic profile have filtering disabled?
There are options to do that in the drop-down menu "Network Filter".
[image: ovirt-network-filter.png]
On Fri, Nov 1, 2019 at 7:35 AM wrote:
> Hi @hotomoc,
>
> Nothing, it seems there are some filter or like this.
> Maybe some expert
Current oVirt node-ng uses 6
]# yum list installed |grep gluster
gluster-ansible-cluster.noarch1.0.0-1.el7
installed
gluster-ansible-features.noarch 1.0.5-3.el7
installed
gluster-ansible-infra.noarch 1.0.4-3.el7
installed
log into the ovirt node, and "yum update ovirt-node-ng-image-update" and
reboot.
On Wed, Oct 9, 2019 at 4:51 AM Sven Achtelik wrote:
> Hi All,
>
>
>
> is there a way to go from 4.2.8 on ovirt node to go directly to the latest
> version, without reinstalling the node from the iso file ? I wasn’t
For number 2, I'd look at the actual gluster file directories, in which I'd
expect to see host3 is missing the files.
I'd rsync the files from one of the other hosts to the same location on
host3 and then run the "gluster heal volume engine".
Since its the engine volume, I wouldn't be surprised
I haven't tried many but for one I just untarred the thing to get the disk
image file and created a new VM with that.
Sometimes the ova file is compressed/assembled in some way that might not
be compatible.
On Fri, Feb 28, 2020 at 1:12 AM Jayme wrote:
> If the problem is with the upload process
Check the actual disk image storage for ownership/permissions issues.
A while back there was a bug that caused VM disk images to be changed from
vdsm:kvm ownership to root.
On Fri, Feb 7, 2020 at 3:26 PM Crazy Ayansh
wrote:
> There are 6 VM on the server and all were working fine before I
lated, I did this after failing to solve the
> first issue.
>
> On 9/10/20 8:00 AM, Edward Berger wrote:
>
> It sounds like you don't have a proper default route on the VM or the
> netmask is set incorrectly,
> which can cause a bad route.
>
> Look at differences be
It would seem your host can't resolve the ip address for the server FQDN
listed for the NFS server.
You should fix the DNS problem or try mounting via ip address once you're
sure that it is reachable from the server.
On Thu, Sep 10, 2020 at 12:33 PM wrote:
>
It sounds like you don't have a proper default route on the VM or the
netmask is set incorrectly,
which can cause a bad route.
Look at differences between the engine's network config (presuming it can
reach outside the hypervisor host)
and the VM's config. The VM should have the same subnet,
What is the CPU? I'm asking because you said it was old servers, and at
some point oVirt started filtering out old CPU types which were no longer
supported under windows. There was also the case where if a certain bios
option wasn't enabled (AES?) a westmere(supported) reported as an older
For others having issues with VM network routing...
virbr0 is usually installed by default on centos, etc. to facilitate
containers networking via NAT.
If I'm not planning on running any containers I usually yum remove the
associated packages,
and a reboot to make sure networking is OK.
As an ovirt user my first reaction reading your message was
"that is a ridiculously small system to be trying ovirt self hosted engine
on."
My minimum recommendation is 48GB of RAM dual xeon, since the hosted
ovirt-engine installation by default
wants 16GB/4vCPU. I would use a basic
for installation time failures of a hosted engine system, look in
/var/log/ovirt-hosted-engine-setup
On Mon, Oct 12, 2020 at 7:50 AM wrote:
> What logs are required?
>
>
>
> Yours Sincerely,
>
>
>
> *Henni *
>
>
>
> *From:* Edward Berger
> *Sent
I'm installing 4.4.3-pre on CentOS8.2 and it seems the glusterfs-server
and gluster-ansible-roles RPMs aren't installed,
with the ovirt-cockpit which pulls other dependencies.
This caused the cockpit hyperconverged installer to fail. It mentions the
roles rpm but not the glusterfs
with the role
es >= 1.0-19 needed by
ovirt-engine-metrics-1.4.2-1.el8.noarch
(try to add '--skip-broken' to skip uninstallable packages or '--nobest' to
use not only best candidate packages)
On Mon, Oct 19, 2020 at 12:25 PM Edward Berger wrote:
> I'm installing 4.4.3-pre on CentOS8.2 and it seems
roughly matching what will be shipped in upcoming RHEL
On Tue, Oct 20, 2020 at 4:54 AM Sandro Bonazzola
wrote:
>
>
> Il giorno lun 19 ott 2020 alle ore 19:03 Edward Berger <
> edwber...@gmail.com> ha scritto:
>
>> with those packages installed I was able to run the si
If its in an NFS folder, make sure the ownership is vdsm:kvm (36:36)
On Sat, Sep 26, 2020 at 2:57 PM matthew.st...@fujitsu.com <
matthew.st...@fujitsu.com> wrote:
> I’ve created and ISO storage domain, and placed ISO’s in the export path
> do not show up under Storage > Storage Domains > iso >
I've had situations where the engine UI wouldn't update for
shutdown/startups of VMs which were resolved after ssh-ing into the engine
VM and running systemctl restart ovirt-engine.service. running
engine-setup was also used on occasion and cleared out old tasks.
On Fri, Sep 18, 2020 at 1:26 AM
For oVirt nodes upgrading from 4.4.0 to 4.4.2 you must remove the LVM
filter before the node upgrade produces a proper booting host.
Its in the upgrade release notes as a known issue.
https://www.ovirt.org/release/4.4.2/
On Fri, Oct 2, 2020 at 1:39 PM Erez Zarum wrote:
> Hey,
> Bunch of
If I'm not mistaken manageiq is the suggested solution to manage multiple
ovirt clusters with their own engines.
On Tue, Aug 4, 2020 at 2:45 PM Holger Petrick
wrote:
> Hello,
>
> I'm looking to deploy oVirt for a company which has locations in different
> countries.
> As I know and also set up
Yes. You can add compute only nodes to a hyperconverged cluster to use the
same storage.
On Tue, Aug 4, 2020 at 7:02 AM Benedetto Vassallo <
benedetto.vassa...@unipa.it> wrote:
> Hi all,
> I am planning to build a 3 nodes hyperconverged system with oVirt, but I
> have a question.
> After
4 to fail.
>
> I will try to think about a possible workaround.
> Can you please create a bug
> <https://bugzilla.redhat.com/enter_bug.cgi?product=vdsm>?
>
> Thank you.
> Best regards,
> Ales
>
> On Mon, Aug 3, 2020 at 10:58 AM Ales Musil wrote:
>
>&g
I had an issue like this where I was using a centos7 (targetcli iscsi)
server which accidentally had LVM enabled upon reboot
which grabbed the RAID device and stopped targetcli from exporting the RAID
disk as iscsi.
It only showed up after a power outage and it took me a while to figure out
what
While ovirt can do what you would like it to do concerning a single user
interface, but with what you listed,
you're probably better off with just plain KVM/qemu and using virt-manager
for the interface.
Those memory/cpu requirements you listed are really tiny and I wouldn't
recommend even
cockpit hosted-engine deploy fails after defining VM name with static
address with similar python2 error.
[image: engine-deploy-fail.JPG]
On Fri, Jul 17, 2020 at 6:44 AM Gobinda Das wrote:
> Hi Gianluca,
> Thanks for opening the bug.
> Adding @Prajith Kesava Prasad to look into it.
>
>
> On
Same issue with ovirt-node-ng-installer 4.4.1-2020071311.el8 iso
[image: gluster-fail.PNG]
On Thu, Jul 16, 2020 at 9:33 AM wrote:
> I also have this message with the deployment of Gluster. I tried the
> modifications and it doesn't seem to work. Did you succeed ?
>
> here error :
>
> TASK
the 4.4.1 72310 node-ng iso has a broken installer. It failed to find my
regular ethernet interfaces and gave the no networks error.
The 4.4.2-rc seems to be working fine hosted-engine installer wise, to an
nfs mount for the engine VM storage. I didn't try the gluster wizard.
On Thu, Jul 30,
the hyperconverged gluster RPMs aren't installed by default on Enterprise
Linux with the cockpit RPM but are installed on the oVirt node-ng install.
The quick install neglects this, so look at
The hosted engine fqdn and IP address should be separate from the
hypervisor host's IP address but on the same network so it can communicate
to the host through a bridged interface that the installer creates on the
hypervisor host for the hosted engine VM.
On Mon, Dec 28, 2020 at 3:14 PM lejeczek
It seems to be failing on adding the ovirtmgmt bridge to the interface
defined on the host as part of the
host addition installation process. I had this issue during a
hosted-engine install when ovirtmgmt was on a tagged
port which was already configured with a chosen name not supported by the
71 matches
Mail list logo
