Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
Hi Lars, Can you please attach your vdsm and supervdsm logs. Is vdsm service is running? can you reach vdsm client? Michael - Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Sent: Wednesday, January 14, 2015 2:25:53 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing Hey Michael. I keep getting this: Host base does not comply with the cluster Default networks, the following networks are missing on host: 'ovirtmgmt' But based on the installation log, nothing goes wrong doing installation/setup of the host. And I get the same result as the screen shot I send before. Thanks and Best Regards - Lars On 14/01/15 12:42, Michael Burman wrote: No Problem, But don't re-install ovirt, remove host and install him again. not ovirt. it should work. - Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Sent: Wednesday, January 14, 2015 1:41:07 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing I will try to re-install ovirt. Thanks a lot for your help Michael Best Regards - Lars On 14/01/15 12:38, Michael Burman wrote: Hmm I see, It looks like your host is not installed properly, you should have seen the host NIC's on your left in the SetupNetworks window. I recommend to remove host from ovirt and install it again from start. If your 'em1' NIC configured with dhcp, 'ovirtmgmt' should get ip from the NIC after installation. If after installation your 'ovirtmgmt' will be missing on host, try to drag it manually like i said. Before that try to restart network service: 'service network restart' and 'service vdsmd restart' and 'service NetworkManager stop' and then install the host in your ovirt. Hope this help.. Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Sent: Wednesday, January 14, 2015 11:13:27 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 14/01/15 09:55, Michael Burman wrote: Hey Lars, Which OS do you running? You can go to your Ovirt go to Hosts tab Networks Interfaces subtab 'SetupNetworks' . If you changed the lines in the ifcfg files like i said, just attach the 'ovirtmgmt' to 'em1' NIC via SetupNetworks. This should work for you. when pressing 'ok' in the SetupNetworks window, it should take the interface configuration and create the bridge ifcfg with the same configuration. Try that.. Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Cc: users@ovirt.org Sent: Wednesday, January 14, 2015 9:55:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing On 13/01/15 16:03, Michael Burman wrote: Also change NAME=em1 to: DEVICE=em1 and remove the # from the BOOTPROTO=none - Original Message - From: Michael Burman mbur...@redhat.com To: Lars Nielsen l...@steinwurf.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 4:48:55 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
- Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Cc: users@ovirt.org Sent: Wednesday, January 14, 2015 9:55:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 16:03, Michael Burman wrote: Also change NAME=em1 to: DEVICE=em1 and remove the # from the BOOTPROTO=none - Original Message - From: Michael Burman mbur...@redhat.com To: Lars Nielsen l...@steinwurf.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 4:48:55 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? Can you please? Including OSes of each machine? Which packages you installed, from which repo? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users Hey. I have had a look at this. This /etc/init.d/ovirt-engine, we also do not have on our system. You won't find it on fedora
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
On 14/01/15 09:43, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Cc: users@ovirt.org Sent: Wednesday, January 14, 2015 9:55:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing On 13/01/15 16:03, Michael Burman wrote: Also change NAME=em1 to: DEVICE=em1 and remove the # from the BOOTPROTO=none - Original Message - From: Michael Burman mbur...@redhat.com To: Lars Nielsen l...@steinwurf.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 4:48:55 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? Can you please? Including OSes of each machine? Which packages you installed, from which repo? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users Hey. I have had a look at this. This /etc/init.d/ovirt-engine, we also do not have on our system. You won't find it on fedora, this is a sysvinit script. On fedora you should have /usr/lib/systemd/system/ovirt-engine.service . So how can I restart my oVirt instance? For both systemd and sysv, this should work: service ovirt-engine
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
On 14/01/15 09:43, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsen l...@steinwurf.com To: Michael Burman mbur...@redhat.com Cc: users@ovirt.org Sent: Wednesday, January 14, 2015 9:55:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing On 13/01/15 16:03, Michael Burman wrote: Also change NAME=em1 to: DEVICE=em1 and remove the # from the BOOTPROTO=none - Original Message - From: Michael Burman mbur...@redhat.com To: Lars Nielsen l...@steinwurf.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 4:48:55 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? Can you please? Including OSes of each machine? Which packages you installed, from which repo? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users Hey. I have had a look at this. This /etc/init.d/ovirt-engine, we also do not have on our system. You won't find it on fedora, this is a sysvinit script. On fedora you should have /usr/lib/systemd/system/ovirt-engine.service . So how can I restart my oVirt instance? For both systemd and sysv, this should work: service ovirt-engine
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
- Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: Michael Burman mbur...@redhat.com, users@ovirt.org Sent: Wednesday, January 14, 2015 10:51:19 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing [snip] We are testing out, different solution for virtualization, to set up a more diverge build environment. OK. So I am testing out oVirt for this purpose, and I am at the stage where I am to setup the first host. Meaning, you have the engine up and running on some machine (VM), and now try to install a host. Right? Which OSes? However, when the host it setup, I get the error NonOperational, because it can not find the ovirtmgmt network on the machine. Please post the host-install log of this host. You should find it on engine machine in /var/log/ovirt-engine/host-deploy . As mentioned already, there are problems with NetworkManager. I suggest to remove it completely from the host, make sure networking works well, then try to reinstall the host from the web admin. If it fails, please post host-install logs. Thanks. Best, -- Didi ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
On 14/01/15 10:25, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: Michael Burman mbur...@redhat.com, users@ovirt.org Sent: Wednesday, January 14, 2015 10:51:19 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing [snip] We are testing out, different solution for virtualization, to set up a more diverge build environment. OK. So I am testing out oVirt for this purpose, and I am at the stage where I am to setup the first host. Meaning, you have the engine up and running on some machine (VM), and now try to install a host. Right? Which OSes? However, when the host it setup, I get the error NonOperational, because it can not find the ovirtmgmt network on the machine. Please post the host-install log of this host. You should find it on engine machine in /var/log/ovirt-engine/host-deploy . As mentioned already, there are problems with NetworkManager. I suggest to remove it completely from the host, make sure networking works well, then try to reinstall the host from the web admin. If it fails, please post host-install logs. Thanks. Best, You can find the log file, in this tar ball: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
On 13/01/15 16:03, Michael Burman wrote: Also change NAME=em1 to: DEVICE=em1 and remove the # from the BOOTPROTO=none - Original Message - From: Michael Burman mbur...@redhat.com To: Lars Nielsen l...@steinwurf.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 4:48:55 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users Hey. I have had a look at this. This /etc/init.d/ovirt-engine, we also do not have on our system. So how can I restart my oVirt instance? How ever I have updated the network scripts: https://dl.dropboxusercontent.com/u/55488/network_scripts.tar To me this seems stranger and stranger, in the sense that we are missing stuff. I have followed the oVirt documentation doing installation, which I assume is correct. Thank and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
- Original Message - From: Lars Nielsen l...@steinwurf.com To: users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, -- Didi ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users -- Michael Burman Intern in RedHat Israel, RHEV-M QE Network Team Mobile: 054-5355725 IRC: mburman ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsen l...@steinwurf.com To: users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Thanks and best regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
- Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsen l...@steinwurf.com To: users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! -- Didi ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing
Also change NAME=em1 to: DEVICE=em1 and remove the # from the BOOTPROTO=none - Original Message - From: Michael Burman mbur...@redhat.com To: Lars Nielsen l...@steinwurf.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 4:48:55 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmtnetwork missing Hi Lars First of all you have to decide from where your ovirtmgmt getting the ip, if it is from a dhcp server, you have to delete this lines from your ifcfg-ovirtmgmt file: IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 and add the next line: NM_CONTROLLED=no - in the ifcfg-em1 file change: BOOTPROTO=none and add the line: NM_CONTROLLED=no restart your engine /etc/init.d/ovirt-engine restart and make sure your ovirtmgmt got ip and you have a default gateway, you can run: route -n Put your host in maintenance mode , try to activate or re-install. Best regards, Michael B - Original Message - From: Lars Nielsen l...@steinwurf.com To: Yedidyah Bar David d...@redhat.com Cc: users@ovirt.org Sent: Tuesday, January 13, 2015 12:05:05 PM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 10:33, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To: Yedidyah Bar Davidd...@redhat.com Cc:users@ovirt.org Sent: Tuesday, January 13, 2015 11:26:55 AM Subject: Re: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing On 13/01/15 09:31, Yedidyah Bar David wrote: - Original Message - From: Lars Nielsenl...@steinwurf.com To:users@ovirt.org Sent: Tuesday, January 13, 2015 10:20:20 AM Subject: [ovirt-users] Host in NonOperational mode ovirtmgmt network missing Hey I am new to oVirt, so please be patient I have a problem, when setting up new hosts. Doing the setup it self no problem, but afterwards the status is set to NonOperational. Do to the network ovirtmgmt is missing on the machine. However I have added the following ifcfg file: ifcfg-ovirtmgmt:: DEVICE=ovirtmgmt TYPE=Bridge ONBOOT=yes DELAY=0 BOOTPROTO=dhcp IPADDR=192.168.1.10 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 And made the adjustments, so the ifcfg-en1, file looks like this: TYPE=Ethernet #BOOTPROTO=dhcp DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=em1 UUID=bdc14160-3cb6-48d7-b8b9-a382dc384add ONBOOT=yes HWADDR=F8:B1:56:C1:F9:8E PEERDNS=yes PEERROUTES=yes BRIDGE=ovirtmgmt I do realize that, the guides on the web for oVirt set BOOTPROTO to static. But at the office, we do not have the possibility of static IP, at the moment. Can some one please tell me what could be wrong ? dhcp should work too. The problem is with NetworkManager. You'll need to have static IPs though for the engine to be able to contact the hosts (as well as the hosts themselves, for hosted-engine HA at least), or you'll have problems if they for some reason get a different IP address from your dhcp server. Please post relevant logs: hosts - /var/log/ovirt-hosted-engine*/*, /var/log/vdsm/* engine - /var/log/ovirt-engine/* Thanks and best regards, Okay something seems to be a food here, because on the server hosting our oVirt instance. We do not have a /var/log/ovirt-hosted-engine directory. I didn't say you should - I wrote a '*' in the end. You should find /var/log/ovirt-hosted-engine-ha /var/log/ovirt-hosted-engine-setup But now I realize you did not mention hosted-engine. Can you detail a bit your setup? Where is the engine? Where are the hosts? How did you install and setup? However the log files from the two other directories, can be found here: https://dl.dropboxusercontent.com/u/55488/ovirt_ovirtlogs.tar Please add from engine also /var/log/ovirt-engine/host-deploy/* . Thanks! We do not have any ovirt-hosted-engine-* on the server, how ever here is a link to the complete ovirt-engine folder: https://dl.dropboxusercontent.com/u/55488/ovirt-engine.tar Thanks and Best Regards - Lars ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users -- Michael Burman Intern in RedHat Israel, RHEV-M QE Network Team Mobile: 054-5355725 IRC: mburman ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users -- Michael Burman Intern in RedHat Israel, RHEV-M QE Network Team Mobile: 054-5355725 IRC: mburman ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
