Hi, The calculation of the tx rate in percentage is -
txDiff = currentCumulativeTx - previousCumulativeTx timeSlot = currentTime - previousTime txRate = txDiff / timeSlot ratePercentage = 100 * txRate / speed The message is displayed in case 'ratePercentage' is bigger than 95%. If you have 'dwh' installed you can see the history. Alona. tx On Wed, Mar 8, 2017 at 11:30 AM, Gianluca Cecchi <gianluca.cec...@gmail.com> wrote: > Hello, > this morning I get these two messages regarding bond1 and its active > interface on one host (ovmsrv07): > > Host ovmsrv07 has network interface which exceeded the defined threshold > [95%] (bond1: transmit rate[96%], receive rate [0%]) > > Host ovmsrv07 has network interface which exceeded the defined threshold > [95%] (enp7s4f0: transmit rate[96%], receive rate [0%]) > > Actually there is no particular network activity during this latest > night... > There have been some different resore jobs during past days... > How is determined this message? Is it perhaps cumulative? > > On the host there are 3 VMs and only one of them actively using the > network. > In its "Network Interfaces subtab I see > Total RX (bytes) > 542,696,952,529 > > Inside VM OS: > $ uptime > 10:26:50 up 14 days, 1:35, 3 users, load average: 0.00, 0.04, 0.05 > > $ ifconfig eth0 > eth0 Link encap:Ethernet HWaddr 00:1A:4A:17:01:5B > inet addr:10.4.4.66 Bcast:10.4.4.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:40280066 errors:0 dropped:612718 overruns:0 frame:0 > TX packets:21110417 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:193066319488 (179.8 GiB) TX bytes:20983189756 (19.5 > GiB) > > Almost confirmaed on host where I have these counter indeed, but I think > they are cumulative for the VM, and not an alert in se.... > > ON ovmsrv07: > $ ifconfig bond1 > bond1: flags=5187<UP,BROADCAST,RUNNING,MASTER,MULTICAST> mtu 9000 > ether 00:1c:c4:ab:3a:dd txqueuelen 1000 (Ethernet) > RX packets 140610596 bytes 200368822262 (186.6 GiB) > RX errors 0 dropped 126874 overruns 0 frame 0 > TX packets 33886066 bytes 21972025081 (20.4 GiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > > $ cat /proc/net/bonding/bond1 > Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) > > Bonding Mode: fault-tolerance (active-backup) > Primary Slave: None > Currently Active Slave: enp7s4f0 > MII Status: up > MII Polling Interval (ms): 100 > Up Delay (ms): 0 > Down Delay (ms): 0 > > Slave Interface: enp7s4f0 > MII Status: up > Speed: 1000 Mbps > Duplex: full > Link Failure Count: 0 > Permanent HW addr: 00:1c:c4:ab:3a:dd > Slave queue ID: 0 > > Slave Interface: enp7s4f1 > MII Status: up > Speed: 1000 Mbps > Duplex: full > Link Failure Count: 0 > Permanent HW addr: 00:1c:c4:ab:3a:de > Slave queue ID: 0 > > Could anyone clarify? > > Thanks, > Gianluca > > _______________________________________________ > Users mailing list > Users@ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > >
_______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users