Re: [WISPA] Dual WAN Router

2008-05-16 Thread Steve Barnes
I have had some poor results with dual wan routers for SOHO. Load balancing really causes issues due to connection switching in the middle of a session. Fail over works OK generally but never seen one that you can separate in-bound and out-bound to different wans. Suppose if you set WAN1 as the

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Larry A Weidig
We have been using the Linksys RV042 and RV082 routers which both have dual WAN ports. We have had good success with these. The only difference being 4 10/100 or 8 10/100 ports. Hope this helps! Larry -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Scott Reed
Mikrotik. The new 433 board will support 3 Ethernet and 3 wireless cards. Full routing, VPN server/client, ... Eric Merkel wrote: Anyone have any recommendations on a dual wan router? We plan to setup a customer on DSL and wireless and use the wireless for terminating VPN traffic and DSL for

Re: [WISPA] Dual WAN Router

2008-05-16 Thread David E. Smith
Steve Barnes wrote: Anyone have any recommendations on a dual wan router? We plan to setup a customer on DSL and wireless and use the wireless for terminating VPN traffic and DSL for internet traffic and then failover for redundancy. Standard get a Mikrotik spiel goes here. One of my

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Dennis Burgess
Subject: Re: [WISPA] Dual WAN Router Steve Barnes wrote: Anyone have any recommendations on a dual wan router? We plan to setup a customer on DSL and wireless and use the wireless for terminating VPN traffic and DSL for internet traffic and then failover for redundancy. Standard get

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Kurt Fankhauser
List Subject: Re: [WISPA] Dual WAN Router Steve Barnes wrote: Anyone have any recommendations on a dual wan router? We plan to setup a customer on DSL and wireless and use the wireless for terminating VPN traffic and DSL for internet traffic and then failover for redundancy. Standard get

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Eric Merkel
Does Mikrotik have the dead gateway feature? Basically it pings the gateway on the interface and if it fails only uses the remaining interface for new sessions? I am not looking for a solution that uses dynamic routing protocols such as BGP or OSPF. I am looking for something more geared to the

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Travis Johnson
orks great! -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of David E. Smith Sent: Friday, May 16, 2008 10:08 AM To: WISPA General List Subject: Re: [WISPA] Dual WAN Router Steve Barnes wrote: Anyone have any recommendations on a dual wan route

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Randy Cosby
http://wiki.mikrotik.com/wiki/Routing Quite a few examples and ideas of how to do this. Maybe this would be a good place to start. If these look like more than you want to bite off, hire an expert, or buy a pre-configured unit like a Linksys. -- Randy Cosby Vice President InfoWest, Inc

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Dennis Burgess
great! -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of David E. Smith Sent: Friday, May 16, 2008 10:08 AM To: WISPA General List Subject: Re: [WISPA] Dual WAN Router Steve Barnes wrote: Anyone have any recommendations on a dual wan router? We

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Dennis Burgess
: Friday, May 16, 2008 11:23 AM To: 'WISPA General List' Subject: Re: [WISPA] Dual WAN Router We did do a location with 3 DSL Providers, 4 DSLs on EACH provider with Mikrotik, a PowerRouter and Procurve switch. Works great! -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Eric Merkel
On Fri, May 16, 2008 at 11:49 AM, Eric Merkel [EMAIL PROTECTED] wrote: Does Mikrotik have the dead gateway feature? Basically it pings the gateway on the interface and if it fails only uses the remaining interface for new sessions? I am not looking for a solution that uses dynamic routing

Re: [WISPA] Dual WAN Router

2008-05-16 Thread David E. Smith
Eric Merkel wrote: Does Mikrotik have the dead gateway feature? Yup. When creating routes, there are a few options under check-gateway, including ping (if the gateway for a given route isn't pingable it isn't used). Travis Johnson wrote: How does this work if they are using a real subnet

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Scott Reed
Yes, you can setup the dead gateway feature. Check out the MT site for how-to documents and a list of consultants that can help. Eric Merkel wrote: Does Mikrotik have the dead gateway feature? Basically it pings the gateway on the interface and if it fails only uses the remaining interface

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Mike Hammett
] Dual WAN Router On Fri, May 16, 2008 at 11:49 AM, Eric Merkel [EMAIL PROTECTED] wrote: Does Mikrotik have the dead gateway feature? Basically it pings the gateway on the interface and if it fails only uses the remaining interface for new sessions? I am not looking for a solution that uses

Re: [WISPA] Dual WAN Router

2008-05-16 Thread Matt Hardy
- Original Message - From: Eric Merkel [EMAIL PROTECTED] To: WISPA General List wireless@wispa.org Sent: Friday, May 16, 2008 1:27 PM Subject: Re: [WISPA] Dual WAN Router On Fri, May 16, 2008 at 11:49 AM, Eric Merkel [EMAIL PROTECTED] wrote: Does Mikrotik have the dead