Srijayanthi
the problem was tabs in the parameter file. remeove them and it works. it
could be seen from the print.out file where all layer thicknes's were
zero
jens
On Fri, 18 Mar 2011, srijayanthi G wrote:
ok Jens I will wait for your reply.
Thank you
G.Srijayanthi
On Fri, Mar 18, 2011 at 3:52 PM, Jens Havskov <[email protected]>
wrote:
got your data, seems lik the h_models files causes the probelm,
will have to check a bit more
jens
On Thu, 17 Mar 2011, srijayanthi G wrote:
Ok,
I am attaching the files to this mail.
I will attach my S-files in the next mail.
Regards
G.Srijayanthi
On Wed, Mar 16, 2011 at 11:09 PM, Jens Havskov
<[email protected]>
wrote:
On Wed, 16 Mar 2011, srijayanthi G wrote:
Sir,
Yes, I wanted origin time for comparison only. But,
please
correct me for a
small doubt that I have "if the origin time is given
in 1
digit than why is
the error in origin time given in 2 decimals ?"
probably because there was room for 2, dont remeber
Do I send one event file?( to check the HYP for
different
models.)
i need the files you use
jens
Thank you
Regards
G.Srijayanthi
On Wed, Mar 16, 2011 at 4:07 PM, Jens Havskov
<[email protected]>
wrote:
Srijayanthi
maybe you are right, oring time migh only be 1
digit.
but for
normal use thats id enough, iu suppose you only
needed it for
comparison. to find out why multi models do not
work
i need the
event file, station file and h file
jens
On Wed, 16 Mar 2011, srijayanthi G wrote:
Sir,
I am really very thankful for your helpful
reply.
1. How to run HYP for
crustal
studies ?
(given in Pg
No 62 of Seisan manual)
I tried to do this but an
error
occurred.. Need your
kind help to resolve,
it would be great if a
test
file
with
clear
procedure be provided.
are you trying to run with multiple
models
?
without
knowin what error
message is, it is hard to answer your
question
I copied the same h_models.par file
given
in
the DAT
directory. And tried to
run hyp, I am getting the following
error
message.
dtdx2 error: p >= 1/v( 1)
Less than three valid phases for
this
event at
its
present location: no
result
# 48 2009 110 1213 21.1 L
16.873
73.618
8.7
KOY 4 0.8
1.8LKOY
STOP WITH STATUS= 3
rewind: illegal unit number
apparent state: unit 6 (unnamed)
last format: list io
lately writing sequential formatted
external IO
Abort
The event at which it stops is
locatable.
Anyway I
still tried to remove
this event from the database and run
again.
However,
the same error message
repeats.
i have just tested and it seems to work. you
could
have a
specific
case. however, you have to use the same station
file
for
all events.
how many model are you trying ? is it getting
through
one
round before
crash ?
Yes, I am using the same STATION0.HYP file for
all
events.
Still, it stops
at some event and gives the error that I
mentioned
above
before completing
one round. What does this "dtdx2 error: p >=
1/v( 1)"
signify ?
I am running HYP in the terminalas an individual
program,
not at EEV.
If I try this at EEV it gives "Wrong Choice,Try
Again
"
message.
>
2. The origin time in
S-file is
round off
to 1 digit
after the decimal and
in hypsum.out file it is 2
digits
after
the decimal.
It is very unfortunate
to compare both to grep
the
corresponding
error in
depth and error in
horizontal for that
particular
event. Can
you please
suggest how to adjust
these settings ?
you can get 2 digits in s-file by
running
in
high
accuracy mode, set
in SEISAN.DEF. but then the decimal
point
is
not
printed out. what are
you trying to compare ?
Sir can you please let me know the
parameter
which
needs to be set to get
this.
you set the high accuracy parameter in
SEISAN.DEF
HIGH ACCURACY: Setting it to 1.0 enables high
accuracy
operation. This
parameter affects programs
MULPLT, HYP and UPDATE
Do you mean that it (2 decimal places for
origin
time
and
also depth) will
be displayed but not stored in S-file??
it is stored in s-file
I set HIGH_ACCURACY parameter to 1.0 in
SEISAN.DEF
file(earlier not
defined). However, it does not give an origin
time
with 2
decimal places. I
tried to put the same parameter in MULPLT.DEF
and I
am
getting a 3 decimal
place in seconds when displayed and also stored
in
the
S-file for the EPg
picked time.
How do I deal with this ?
Actually, I need the errors in
location
parameters,
which I am unable to get
from S-file.
they are written on the E-line
So I am trying to compare the events located in
S-file and
trying get the error details of the
corresponding
event
from hypsum.out
file(where errors are stored).
And also the magnitudes are not
displayed
it
just
gives 0 for
0.1-0.9 and 1 for 1.0-1.9 and so on..
where is thsi round off ?
This is in the hypsum.out file.
you have all the information in the s-file so
there
si no
need to use
hypsum.out filer. but the s-file must be updated
of
course
I am able to get the errors from S-files and
thank
you so
much for that.
--
Regards,
G. Srijayanthi
--
Regards,
G. Srijayanthi
--
Regards,
G. Srijayanthi
--
Regards,
G. Srijayanthi
_______________________________________________
seisan mailing list
[email protected]
http://mailman.uib.no/listinfo/seisan
