----- Original Message -----
From: <[email protected]>


> Thanks so much, Ivan...let me make sure I am clear about a couple of
things
> in your post...
>
> << The longer the electrodes the more current you will draw and the
>  quicker the reaction will be.
>  How long it will take depends on your 'recipe'. Voltage, current
limit
>  (or not), electrode length, distance apart. 76 oz = 2.25L, if the
>  electrodes are 6" long, 2" apart, you run with 27V and have no
current
>  limit, then I would guess 10ppm in about 3 hours.>>
>
> If my wires are 9" in the water (at that length, they would almost
touch the
> bottom of the container) and one or two inches apart (does it
> matter?)...Would that work?  Is there something I should know about
the
> distance between the wires v. length of the wires?  Would the length
of time
> be shortened by the extra wire?  Would I run the test partially by
sight
> evaluation?  (Stop one test at guesstimated time, another when the
golden
> color appears?)

Keep the wires a quarter to half an inch off the bottom, keep the
wires as far apart as possible keeping an inch or so between them and
the side of the container. This will limit the build up of trees or
sludge on the negative electrode (cathode). More wetted electrode area
means more current flow and therefore less generation time, at the
expense of quicker current rise and less controll.
If you have the equipment, monitor voltage and current, and using the
formula: resistance = voltage (in volts) divided by current (in amps,
1mA = 0.001A) stop one run when the resistance equals about 20,000
ohms after stirring. If you are using water equivalent to mine then
this should equate to 10 to 15 ppm.
I should imagine with a non current limited system your cs will be
yellow at this point, perhaps quite deep yellow.

> Ivan, re your next thought (below)...
>
> <<How long the batteries would last, I don't know. Why not buy a
small
>  power supply, say 24V, this would allow for repeatable results and

>  enable proper evaluation of test runs.>>
>
> ...I'm hoping by now you are realizing you are talking to a nursery
school
> student in connection with these electrical issues.  I was thinking
3   9V
> batteries (the rectangular type, with the positive and negative
connections
> on the top of the battery) was a small power supply.  I don't know
what 24V
> is...is that larger or smaller than 3 9V batteries?  What sort of
power
> supply is a 24V?  A car battery?

Well, a car battery (12V,  as opposed to 3 x 9V = 27V) would work very
well but you would need to go for another hour or so. A battery is a
subset of the class 'power supply'. When one refers to a power supply
one is generally talking of a regulated output from a box plugged into
the wall. They are relatively inexpensive (at least the ones 5V to 24V
are), and provide a reliable output. I believe Radio Shack (Rat shack)
or Tandi can supply these.

> Believe me, it is a little painful to be this ignorant!

Jeese don't I know... every body has to start somewhere.

> << Do two or three runs of
>  different time lengths and send samples to Robert Berger for
testing.>>
>
> Thanks, I will do this...
>
> I appreciate your help so much!
> Taylor

My pleasure
Ivan.



--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]

List maintainer: Mike Devour <[email protected]>