The Alchemists distilled 7 times to assure complete demineralization Trem
----- Original Message ----- From: needling around To: [email protected] Sent: Monday, August 16, 2010 11:36 AM Subject: Re: CS>twice distilled water Thanks. I understand that but once you distill it aren't they all supposed to be gone? The reason I double distilled it was because the homeopath wants it totally destructured before I use it. I thought singly distilled water was the purest water there was. I was surprised that it still contained contaminants. PT ----- Original Message ----- From: Trem To: [email protected] Sent: Monday, August 16, 2010 1:36 PM Subject: Re: CS>twice distilled water The reason for double distillation is to remove most of the caontamimamts (minerals) The water is not producing contaminants. They were in it to start with. Trem ----- Original Message ----- From: needling around To: [email protected] Sent: Monday, August 16, 2010 9:49 AM Subject: Re: CS>twice distilled water Actually, the CS that I made with the water turned out OK. What I am interested in is how water that has been distilled can still be producing contaminants? It was my understanding that once it was distilled it is contaminant free. Thanks. PT ----- Original Message ----- From: Trem To: [email protected] Sent: Monday, August 16, 2010 12:38 PM Subject: Re: CS>twice distilled water Sometimes following steps 1 through 4 is good enough. All steps are for making the best end product. Starting with RO is a good first step since much most minerals are removed but it migh also be OK starting with tap water. Experiment and you'll soon know. Trem ----- Original Message ----- From: jaxi To: [email protected] Sent: Monday, August 16, 2010 8:39 AM Subject: Re: CS>twice distilled water Found it ... see below. Question - if using RO water to start would you still need to "double distill"? I haven't bought my distiller yet but it begins to seem like a hell of a lot more work to make the distilled water than it is to make the EIS. Jaxi How to use a tabletop water distiller to produce very low conductivity, high quality distilled water used to make ionic/colloidal silver water. 1. Remove the carbon discharge filter. It makes the water conductive. 2. Fill the boiling chamber no more than 3/4 full. 3. Distill only 1/2 gallon into the receiver. 4. Discard the remainder in the boiling chamber. 5. Repeat steps 2,3 and 4. You now have one gallon in the receiver. 6. Put 3/4 gallon of this water in the boiling chamber. 7. Distill only 1/2 gallon into the receiver. You now have what is called double distilled water. Allow to cool and try to use it. It should measure less than 1 microsiemen using a PWT meter.. On Mon, Aug 16, 2010 at 9:53 AM, Trem <[email protected]> wrote: Try using the method shown just above the links at the bottom of this page. http://www.silvergen.com/links_resources.htm "How to use a tabletop water distiller to produce very low conductivity, high quality distilled water used to make ionic/colloidal silver water." Trem ---------------------------------------------------------------------- No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.851 / Virus Database: 271.1.1/3075 - Release Date: 08/15/10 23:35:00 -------------------------------------------------------------------------- No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.851 / Virus Database: 271.1.1/3075 - Release Date: 08/15/10 23:35:00 ------------------------------------------------------------------------------ No virus found in this incoming message. Checked by AVG - www.avg.com Version: 9.0.851 / Virus Database: 271.1.1/3075 - Release Date: 08/15/10 23:35:00
