Hi Fred and All,

Regarding the correct conversion factor, uS to ppm as silver ions.

Freds message has given me cause to settle this question, at least in my
own mind, once and for all. I do not have much confidence in Hanna Inst.
advice, if some the experiences lister have had are anything to go by,
although I have had no dealings with them myself.

The method I had been using is recommended by other TDS manufacturers,
and turns out to be quick and rough method for assigning equivalent
weights to conductivity measurements. This method does not take into
consideration the different conductivities of ions, and whilst this is
adequate in measuring the concentration of water impurities, as the
conductivity of these impurities is similar, it has about a 30% error
when applied to silver ions.

The conductivity graphs I had made previously were calibrated using a
known concentration of silver nitrate and so the silver readings are
close to being correct.

So yesterday I hit the books etc. and found that the conductivity of
dilute solutions of silver ions is 61.9 Scm^2 M^-1 that is Semen
centimetre squared per Mol.
This is probably where Hanna derived their 1.6 conversion factor, but
this refers to Mols of silver not ppm.
When converted to mg/L we find that: 1mg/L (1ppm) Ag+ = .574 uS/cm or
1uS = 1.74ppm

To check my results, I also derived
KCl        1uS = 0.50ppm
NaCl      1uS = 0.46ppm
CaCO3 1uS = 0.39ppm
AgNO3 1uS = 1.27ppm

These results hold true for very dilute solutions, but as the
concentration increases the conductivity per mg drops in proportion to
the square root of the concentration. This is due to interaction of the
ions with the water molecules and with each other. So the conductivity
vs concentration plot is not a straight line but a curve.

For what it is worth, here are the adjusted values for various
concentrations of Silver, you will notice that the conversion factor
differs by a paltry 0.03 in the decade 5ppm - 50ppm, hardly worth
worrying about.

As Ag+
5ppm     1.76     2.8uS
10ppm   1.76     5.7uS
15ppm   1.77     8.5uS
20ppm   1.77   11.3uS
25ppm   1.78   14.0uS
50ppm   1.79   27.9uS

For those using Silver Nitrate as a standard :

5ppm     3.9 uS
25ppm  19.4uS
50ppm  38.5uS

I have remeasured a few CS samples and have found very good correlation
with ISE readings, as long as the sols were clear or yellow (even deep
yellow), and the Tyndall cone is homogenous, but the two part company,
with the conductivity reading rising, if the sol is gold (which I think
could be yellow with some red reflecting particles) or if the sol has
any *sparklies* within it.

I shall post some graphs, as time permits.

Ivan.




----- Original Message -----
From: Fred <[email protected]>
To: <[email protected]>
Sent: Friday, 22 October 1999 18:04
Subject: Re: CS ppm standard - 1.6uS/PPM


> In reply to Ivan on the 1.6 uS = 1 PPM, I had gotten my conversion
from
> Hanna Instruments. In their manual they say the ratio is from 1.4 to 2
> uS/PPM, the latter being for CaCO2. From a phone discussion with their
> technical people a few years ago I was given the 1.6 conversion number
> for Colloidal Silver! The definition of PPM is by weight, of mg/liter
so I
> assume some chemist on the list could make an accurate solution and
> then check the conductivity to check their conversion ratio.
Incidentially,
> Hanna sells standard solutions of NaCl at 84 uS, which we use to
> verify our meters.
>
> For those that wonder what strength they have made, we always offer
free
> testing of PPM (TDS method). The preparation and mailing info is at
our
> general  health site at <http://www.health2us.com>.
>
>  Yes, I said FREE testing!
>
> [email protected]
>
>
> --
> The silver-list is a moderated forum for discussion of colloidal
silver.
>
> To join or quit silver-list or silver-digest send an e-mail message
to:
> [email protected]  -or-  [email protected]
> with the word subscribe or unsubscribe in the SUBJECT line.
>
> To post, address your message to: [email protected]
>
> List maintainer: Mike Devour <[email protected]>
>