Reference:
         http://web.idirect.com~showcase/althealth/cspulse.htm

Setup:  8oz distilled water in clear glass(no starters or salt added)
            1/16 inch wide flat silver electrodes
            2 1/2 wettec length
            Electrode spacing 1/2 inch
            Pulsed DC generator per above referenced web site
            Pulse rate(frequency) 23.809KHz
            Duty cycle on 54.54% off 45.45%
             water temp around 70 degress F
            Electrodes wiped after run completed
            
20 min. run:

            Start:  .19ma @ 8.13V(measured at electrodes with VOM)
                                             (duty cycle affects the
measurements)

                               For comparison with DC units(no pulsing)

                       8.13/.5454 = 14.9VDC Pulses(checked with O'scope)
                       .19ma/.5454 = .348ma

             End:   [email protected]
                       .85/.5454 = 1.56ma @7.74/.5454 = 14.19VDC

Check CS resistance:  Wiped Electrodes 
                            
                                  Measurement 1:                 Applied(to
electrodes);
                                                                   16.19VDC
Current draw = .63ma
                                                                  V=IR;
16.19/.63ma = 25.698Kohms
               
                                  Measurement 2:             Stirred
solution, waited 1 hour
 
Applied(to electrodes);
                                                                   16.26VDC
Current draw = .71ma
                                                                  V=IR;
16.26/.71ma = 22.901Kohms
               
                                  Measurement 3:              12 - 14 hours
after solution made
                                  Condition change:           Water temp
around 55 degrees F
 
Applied(to electrodes);
                                                                    16.36VDC
Current draw = .51ma
                                                                  V=IR;
16.36/.51ma = 32.05Kohms
               
  
40 min. run:

            Start:  .19ma @ 8.13V(measured at electrodes with VOM)
                                             (duty cycle affects the
measurements)

                               For comparison with DC units(no pulsing)

                       8.13/.5454 = 14.9VDC Pulses(checked with O'scope)
                       .19ma/.5454 = .348ma

             End:   [email protected]
                       1/.5454 = 1.83ma @7.74/.5454 = 14.19VDC

Check CS resistance:  Wiped Electrodes 
                            
                                  Measurement 1:                 Applied(to
electrodes);
                                                                   16.16VDC
Current draw = 1.44ma
                                                                  V=IR;
16.16/1.44ma = 11.22Kohms
               
                                  Measurement 2:             Stirred
solution, waited 1 hour
 
Applied(to electrodes);
                                                                   16.20VDC
Current draw = 1.13ma
                                                                  V=IR;
16.20/1.13ma = 14.336Kohms
               
                                  Measurement 3:              12 - 14 hours
after solution made
                                  Condition change:           Water temp
around 55 degrees F
 
Applied(to electrodes);
                                                                    16.36VDC
Current draw = .74ma
                                                                  V=IR;
16.36/.74ma = 22.18Kohms
               
180 min. run:  Yellow tint

            Start:  .19ma @ 8.13V(measured at electrodes with VOM)
                                             (duty cycle affects the
measurements)

                               For comparison with DC units(no pulsing)

                       8.13/.5454 = 14.9VDC Pulses(checked with O'scope)
                       .19ma/.5454 = .348ma

             End:   [email protected]
                       1.84/.5454 = 3.37ma @7.74/.5454 = 14.19VDC

Check CS resistance:  Wiped Electrodes           
               
                                  Measurement 3:              12 - 14 hours
after solution made
                                  Condition change:           Water temp
around 55 degrees F
 
Applied(to electrodes);
                                                                    16.31VDC
Current draw = 2.11ma
                                                                  V=IR;
16.31/2.11ma = 7.72Kohms
               

Conclusions: Still don't know what PPM I have but I do have somthing to
compare to 
                    for my future CS solutions.

                     Voltage needs to be regulated.

                     Current needs to be limited to around
.5ma(.5ma/.5454=.916ma)
                     at electrodes.  Why?  I noticed at around .4ma tiny
bubbles appeared
                     on the negative electrode, as current increased bubbles
got larger and 
                     floated to top more rapidly.  To achieve the smaller
particle size I believe 
                     the bubbles should remain small and the bubble release
rate(bubbles 
                     releasing and rising to the top of the solution) should
be almost 
                     non-existant.  Any thoughts? 
                     
                     The bubbles consistantly appeared around 7min. from the
start time.
                     
                     The CS cloud consistantly appeared(you had to look
close and at the
                     right angle) at around 2 min. from start time.

                     My electrode spacing is 1/2 apart. I was thinking about
trying the 45mm
                     (1 3/4 inch)spacing in Ivans setup.  Any thoughts?
Advantages or 
                     disadvantages?   Would I gain anything?  Would this
help in correlating
                     data in the two generating process(mine and Ivan)?


                      I would appreciate any thoughts or ideas on how I
could improve my 
                      setup. 

                                                              Thanks,

                                                               BillH
      
                     


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]

List maintainer: Mike Devour <[email protected]>