2001 TV VCR wrote:

>
> Some of you guys are using 120 volts AC rectified and
> filtered to produce ~170 volts DC.  How much current
> are you running?  What is the advantage?
>
> Is it possible to make 5 or 10 ppm CS by the gallon
> without the sludge using low voltage?
>
> Thank you very much for your replies.
>
> Bil
>

Hi Bill and all,

I've been experimenting with various setups and find that 170VDC seems
to work pretty well for me. I tried it because it's easy to obtain. One
rectifier bridge, one capacitor, and a couple of resistors. And, the higher
voltage gets things going quickly. (no isolation be careful!)

I use a 100 ohm resistor in series with the line cord to limit the inrush
current to the capacitor. Without this resistor, the inrush from a 20A circuit
blew my bridge to smoking bits and melted one prong on the line cord, such
that I had to file it to use it again. Course my capacitor is a big computer
cap... an overkill to say the least. Judging from past experience, and how it
momentarily pulled the voltage of the whole house down, I'd say I drew a
good surge of 300 to 500 amps!!!  (I was close to the service panal and that
ckt is wired with 10 AWG!) The 100 ohm resistor did the trick...no more
smoke and flames, and no more "Honey!, are you all right down here?...
Honey??...HONEY???"

I've also found that limiting my current to 0.5 ma produces a clear solution.
However, I do run it about 20 hours. (I just set it up and leave it)  My 
electrodes
are about 5" apart and 2 troy OZ each. If I run higher current the process
moves very quickly but the electrolyte turns yellow.

I'm not sure what yellow electrolyte means. Some say it's bigger particles. I 
have
a hard time with that because I see smaller particles (tyndall) and larger 
particles
(sparkles). The yellow must be something else and of a very small particle in my
thinking...not sure. I find that HVAC will not produce yellow electrolyte no 
matter
how hard I try. If over done, it just seems to cause stronger tyndall, which 
eventually
can be observed as cloudy electrolyte, and fallout of bigger particles.

As far as effect, (I have Lyme) the clear, long run, current limited setup; 
causes the
greater herx. I was surprised by this. I thought it would be weaker by just 
looking
at it. I took more the first time...herxed my socks off!

I think low current produces very fine particles. I observe the buildup on the 
cathode
to be very fine. I'm going to try a little higher current (1ma) soon, to see 
what effect
it has, and if the run time can be shorter. I'm also working on an active 
current limit
circuit that will use 27vdc as the supply.

By far, the greatest herx I've experienced was with CS using HVAC. I used 
20KVAC,
generated by 2 oil burner ignition xformers in series parallel. I let that run 
untill
the water dropped away from the electrode (about an hour). I can only take a 
small
ammount, as the herx is severe.

This is all very unscientific!!!

The other thing I've observed is that the herx seems to be different with the 
HVAC
solution. It seems to flair up different symptoms...more cardiac. Just an
observation...I need to experiment with LV and HV to get a better feel for the
apparent different effect.

Last night I ran a batch at 170VDC with no current limit. I came back one hour
later and the solution was very dark amber and the current was up to 30ma.

Just for kicks, I walked out into the backyard to the (trained) doggy do-do 
spot.
Focusing my flashlight on a fresh mound, I plunged my finger into it. (grosed
out my son big time)

A sniff of the finger quickly verified that contamination was present. I then
sprayed on some of the new batch of CS and very carefully retested (re-sniffed).
There was no detectable odor inspite of visually apparent feculant 
contamination.
I washed my hands anyway!

Any and all comments are welcome as I sort through all of this,

Jeff

HAM AND EGGS
A day's work for a chicken;
A lifetime commitment for a pig.



--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]
Silver-list archive: http://escribe.com/health/thesilverlist/index.html
List maintainer: Mike Devour <[email protected]>