Hi again Can anyone please tell the uses for it? It is so long ago..... I know now how to do it...but what do I do it for?
Thanks again Tracy - not blonde but close somedays! ----- Original Message ----- From: Nick Grant <[email protected]> To: <[email protected]> Sent: Friday, 7 September 2001 08:43 Subject: Re: CS>air brush set instructions > Yes, thankyou so much! > > Tracy > ----- Original Message ----- > From: Dick Tanguay <[email protected]> > To: <[email protected]> > Sent: Thursday, 6 September 2001 23:17 > Subject: Re: CS>air brush set instructions > > > > Tracy, Is this what you are looking for? > > > > ----- Original Message ----- > > From: Brooks Bradley > > To: > > Sent: Sunday, 25 April 1999 10:12 > > Subject: CS>Parts List and Comments on CSXO2 Nebulizing System > > > > > > Good Afternoon List Members. > > Following is a list of the components required for enabling > > the protocol we used in the experimental researches I outlined last > > evening. > > The air-brush kit we used, was obtained from a mail-order > > concern specializing in myriad hardware/electrical/hand-tool items. > > Their quality is toward the low-end industrial, but quite adequate for > > the home/hobby user. Our machine shop/proto-type builders have used > > them for years. The company is Harbor Freight, located in Camarillo, > > California. They now have outlets in one or two other cities. We > > obtained our air-brush kits from the Fort Worth, Texas store (we are > > located in Fort Worth). The stock number is #6131. Our purchasing > > person informed me this item cost us less than $10.00 each, and the > > last 20 purchased cost less than $8.00. As of last Wednesday, this > > store still had some of these units. Included in the kit are two > > liquid -supply bottles (one 1/2 and one 1 oz), one air hose which > > couples between the pressure regulator and the air-brush assembly; > > one air pressure regulator; and the air-brush assembly itself. The > > additional parts required are for a hose assembly which facilitates > > coupling the input side of the air pressure regulator with the > > external oxygen supply used to power the nebulizer. > > Note: PURCHASE BRASS FITTINGS ONLY, oxygen is the > > pre-eminent combustion supporter. > > All of these components can be obtained from any > > commercial outlet stocking pneumatic system parts. > > This hose assembly includes: > > One 1/4" Compression X 1/8" Male NPT fitting (this > > is very important, for without it you cannot connect the O2 hose to > > the air-brush pressure regulator) > > One 1/4" Barb X 1/8" NPTF Fitting > > One 1/4" X 9/16 RH Oxygen Fitting (will have a barb > > fitting on one end and the female coupling on the other) > > Approximately 4 feet of any good !/4 I.D. 200+ > > PSI air hose. Tell the clerk you are going to use oxygen in the > > hose. > > Assemble the parts by screwing the Compression > > fitting into the 1/4" Barb X 1/8" Male NPT fitting. Do not worry, > > only one end of the Compression fitting is compatible with the Barb > > fitting. Next, insert the barb end of this fitting assemby into the > > air hose. Push the hose on until it is jam against the shoulder of > > the fitting. Any small, screw or compression-type clamp may be used > > to add security to the hose/fitting end. Next, insert the barb end of > > the Oxygen fitting into the remaining hose end and secure with any > > satisfactory clamp. Your assembly is now complete. Next, carefully > > screw the exposed male end of the Compression fitting into the bottom > > of the air-brush pressure regulator. Now connect the small-diameter > > air-line between the air-brush assembly and the pressure regulator (it > > is fool-proof, as there is nowhere else this tiny hose can connect). > > Select the small fluid-supply bottle and fill > > approximately 75-80% of capacity with 5-10 ppm Colloidal Silver and > > insert the angled tip assembly into the bottom of the air-brush > > assembly. You are now ready to connect to your O2 supply and operate. > > Obtain a small medical O2 bottle (anywhere around 1/2 > > to 1 cubic feet capacity) or any size O2 Arc welding system bottle. > > Be sure to have a Two-stage regulator attached to the O2 bottle. Now, > > connect the 9/16" Oxygen-fitting to the O2 outlet from the Two-stage > > regulator (also foo-proof, as there is nowhere else to connect). Now > > SLOWLY open the O2 control knob on the O2 regulator and set the inlet > > prssure to your nebulizer assembly to a Maximum of 35 Pounds Per > > Square Inch (PSI). Next, screw the AIR-BRUSH air pressure > > regulator control knob (the tiny knob on top of the air pressure > > regulator) all the way closed.. Now, open the control knob about 2 > > and one-half turns. Next, trigger the control botton on the > > Air-brush head until you see a fine fog each time you press down on > > the > > button. The mist is so fine, you may have to hold it against a dark > > back ground to see it. You are now ready to go. > > Our best results were obtained by the volunteer inserting > > the discharge nozzle about 1 inch inside their OPEN mouth and > > breathing deep---an long---on each inhalation; holding the breath for > > a count of 3 or 4 and then executing a complete exhalation. Ideally, > > there should be about 1/4" circular clearance around the air-brush > > head (while inside the mouth), as this provides the optimum venturi > > action for incorporating air with the O2. In acute circumstances, the > > volunteer can close his/her mouth completely around the nozzle and > > breathe 100% O2------works great. > > Remember NEVER USE PURE OXYGEN NEAR OPEN FLAMES OR > > COMBUSTIBLE MATERIALS. To do so would make this protocol quite > > irrelevant. > > Good luck to all, and if you have any questions just post > > them and I will try to answer. Sincerely. Brooks Bradley. p.s. > > Any serviceable air-brush assembly could be used. However, try to > > obtain one that will yield the smallest size particle possible. > > > > > > > > > > > > ----- Original Message ----- > > From: "Nick Grant" <[email protected]> > > To: <[email protected]> > > Sent: Wednesday, September 05, 2001 8:57 PM > > Subject: CS>air brush set > > > > > > > Brooks > > > > > > Just received from Ivan the air brush set that you sent over. Thanks > > again, > > > and thank you Ivan for sending it to me. Brooks, I tried to find the > info > > > in the archives on what to do with it again - but didn't come up with > > much. > > > have you got a set of instructions you could possibly e-mail me...? > > > > > > If so, my address is [email protected] > > > > > > Thanks again guys > > > > > > Tracy > > > > > > > > > -- > > > The silver-list is a moderated forum for discussion of colloidal silver. > > > > > > To join or quit silver-list or silver-digest send an e-mail message to: > > > [email protected] -or- [email protected] > > > with the word subscribe or unsubscribe in the SUBJECT line. > > > > > > To post, address your message to: [email protected] > > > Silver-list archive: http://escribe.com/health/thesilverlist/index.html > > > List maintainer: Mike Devour <[email protected]> > > > > > > > > >
