Have you tried running over a wired connection, rather than a wireless connection? You might also try running SIMH under a Linux VM.
Zane > On May 9, 2019, at 7:00 AM, Jonathan Welch <jhwe...@gmail.com> wrote: > > The vms systems on our campus are about to be shut down. My former > boss and I would like to still have access to our files, so I've moved > an image of a vax system disk into simh. > > He is a networking expert and I am no slouch, but neither of us can > figure out why we cannot establish any kind of network connection > outside of the simh. > > I've looked back in the archives for help but have only found people > with linux systems or messages of success with UCX. > > This morning I upgraded from Multinet 4.3 to 5.2 and tried to set up > DHCP but that did not work either. > > Npcap is installed. > > If I set my mac address to be the same as that of the host laptop I > can use wireshark to see pings coming out from the vax but there are > no responses. > > I've disabled decnet from starting up to avoid the mac address from > being changed. > > Some guidance in the right direction would be greatly appreciated. > > ---------- > > From my vax.ini file: > set xq mac=08-24-d7-ca-1f-40 > att xq eth3 > > From the simh prompt: > sim> sho eth > ETH devices: > eth0 \Device\NPF_{8E7FBCD3-67EB-4A59-8E35-6713CAB729FA} (Local Area > Connection 2) > eth1 \Device\NPF_{EE67D248-AACC-4A29-99EE-2B84EA08B5EF} (VMware > Network Adapter VMnet8) > eth2 \Device\NPF_{7287895B-5B94-43ED-8AA8-1FF910EA836B} (Wireless > Network Connection 2) > eth3 \Device\NPF_{DC3CD7F8-4BD9-4610-B8DF-20AC5FBD56FC} (Wireless > Network Connection) > eth4 \Device\NPF_NdisWanIp (NdisWan Adapter) > eth5 \Device\NPF_NdisWanBh (NdisWan Adapter) > eth6 \Device\NPF_{B1392056-6E69-421B-9814-6011441195C2} (Wireless > Network Connection 3) > eth7 \Device\NPF_NdisWanIpv6 (NdisWan Adapter) > eth8 \Device\NPF_{C7140267-68CB-485A-B343-5751B1865242} (VMware > Network Adapter VMnet1) > eth9 \Device\NPF_{795E27CA-60AA-4A1E-AAB0-99FB62537868} (Npcap > Loopback Adapter) > eth10 \Device\NPF_{62CD8A59-7E13-401A-90AB-3CFBC37554E8} (Local Area > Connection) > eth11 nat:{optional-nat-parameters} (Integrated > NAT (SLiRP) support) > eth12 udp:sourceport:remotehost:remoteport (Integrated > UDP bridge support) > Npcap version 0.994, based on libpcap version 1.9.1-PRE-GIT > Open ETH Devices: > XQ eth3 (Wireless Network Connection) > Ethernet Device: > Name: \Device\NPF_{DC3CD7F8-4BD9-4610-B8DF-20AC5FBD56FC} > Reflections: 1 > Self Loopbacks Sent: 2 > Self Loopbacks Rcvd: 2 > Host NIC Address: 00:24:D7:CA:1F:40 > Packets Sent: 2 > Packets Received: 26 > Asynch Interrupts: Disabled > Read Queue: Count: 24 > Read Queue: High: 24 > Read Queue: Loss: 0 > Peak Write Queue Size: 0 > BPF Filter: (((ether dst 08:24:D7:CA:1F:40) or (ether multicast)) and not > ((et > her src 08:24:D7:CA:1F:40))) or ((ether dst 08:24:D7:CA:1F:40) and (ether src > 08 > :24:D7:CA:1F:40)) or ((ether dst 00:24:D7:CA:1F:40) and (ether proto 0x9000)) > sim> > > Multinet settings > MultiNet Network Configuration Utility V5.2(107) > [Reading in MAXIMUM configuration from MULTINET:MULTINET.EXE] > [Reading in configuration from MULTINET:NETWORK_DEVICES.CONFIGURATION] > NET-CONFIG>sho > Interface Adapter CSR Address > Flags/Vector > --------- ------- ----------- > ------------ > se0 (Shared VMS Ethernet/FDDI) -NONE- -NONE- -NONE- > [TCP/IP: 10.0.0.150, IP-SubNet: 255.255.255.0, IP-Broadcast: > 10.0.0.255] > [VMS Device: XQA0, Link Level: Ethernet ] > DHCP Client for the interface is enabled > > > Official Host Name: vax1 > Default IP Route: 10.0.0.1 > Domain Nameserver: 127.0.0.1 > Timezone: EST > Timezone Rules: US/EASTERN > Load UCX $QIO driver: TRUE > Load PWIP (Pathworks) driver: TRUE > DHCP Client Flag: 1 > NET-CONFIG> > _______________________________________________ > Simh mailing list > Simh@trailing-edge.com > http://mailman.trailing-edge.com/mailman/listinfo/simh _______________________________________________ Simh mailing list Simh@trailing-edge.com http://mailman.trailing-edge.com/mailman/listinfo/simh