It seems that simh enables 16 DZ lines by default, and this is the config.
I think this matches what RSTS is showing ?
sim> show dz
DZ address=17760100-17760117*, vector=400-414*, BR5, lines=16
not attached, 8b
On Mon, 9 Dec 2019 at 10:29, Johnny Billquist <b...@softjar.se> wrote:
> In RSTS/E, you have DZ11 lines, but they are configured for a CSR of
> 160100 and 160110, and vectors are 400 and 410. I bet that does not
> match what simh thinks...
>
> Johnny
>
> On 2019-12-09 11:25, Trevor Warwick wrote:
> >
> > I'm using "PDP-11 simulator V4.0-0 Current", and getting the same
> > results on Win10 and Linux.
> >
> > I'm booting the full RSTS V7.0-07 disk, built by by Chuck Cranor. This
> > boots fine, and I can log in on the simulated console. However, I can't
> > persuade it to recognise any additional terminals. If I use:
> >
> > set dli enable
> > set dli lines=8
> > attach dli 10001
> >
> > Then I get a telnet server appearing on port 10001, which prints
> > "Connected to the PDP-11 simulator DLI device, line 0" when I boot the
> > RSTS system disk. However, there's no response to any input once RSTS is
> > up and running. I've also tried using a DZ11
> >
> > set dz lines=8
> > attach dz 10002
> >
> > and in that case I don't even get the "Connected...." line from simh.
> > RSTS can apparently see the hardware though:
> >
> > RSTS V7.0-07 llama (DL0)
> >
> >
> > Option: HA
> >
> > HARDWR suboption? LI
> >
> > Name Address Vector Comments
> > TT: 177560 060
> > RK: 177400 220 RK05F units: none
> > RL: 174400 160 Units: 0(RL01) 1(RL01) 2(RL01) 3(RL01)
> > RM: 177440 210 Units: 0(RK06) 1(RK06) 2(RK06) 3(RK06) 4(RK06)
> > 5(RK06) 6(RK06) 7(RK06)
> > RR: 176700 254 BAE=+050, Units: 0(RM03) 1(RM03) 2(RM03)
> > 3(RM03) 4(RM03) 5(RM03) 6(RM03) 7(RM03)
> > TM: 172520 224
> > PR0: 177550 070
> > PP0: 177554 074
> > LP0: 177514 200
> > RX0: 177170 264
> > KL0: 176500 300
> > KL1: 176510 310
> > KL2: 176520 320
> > KL3: 176530 330
> > KL4: 176540 340
> > KL5: 176550 350
> > KL6: 176560 360
> > KL7: 176570 370
> > DZ0: 160100 400
> > DZ1: 160110 410
> >
> > KW11L 177546 100
> > SR 177570
> > DR 177570
> >
> > Hertz = 60.
> >
> > Other: FPU, SL, 22-Bit Addressing, Cache w/address, System ID = 4660
> >
> > If I boot an RSX-11M disk, then additional terminal interfaces seem to
> > work fine, so the problem seems specific to RSTS. I saw references in
> > the list archive to other pre-built systems on www.rsts.org
> > <http://www.rsts.org> but that doesn't seem to be available at the
> > moment, so I can't try another build right now.
> >
> > Any clues on what I'm missing ?
> >
> > Thanks,
> > Trevor
> >
> >
> >
> > _______________________________________________
> > Simh mailing list
> > Simh@trailing-edge.com
> > http://mailman.trailing-edge.com/mailman/listinfo/simh
> >
>
> --
> Johnny Billquist || "I'm on a bus
> || on a psychedelic trip
> email: b...@softjar.se || Reading murder books
> pdp is alive! || tryin' to stay hip" - B. Idol
>
_______________________________________________
Simh mailing list
Simh@trailing-edge.com
http://mailman.trailing-edge.com/mailman/listinfo/simh
