--- On Fri, 1/8/10, Eric Varsanyi <[email protected]> wrote:
> I've been building/running recent
> freeswitch versions (from their nightly tarballs and SVN) on
> FC10 w/o issue. If you have all the prerequisites installed
> its just a matter of cd'ing into the lib directory, then
> sipXfreeswitch and running make. This ultimately just runs
> the normal 'rpmbuild' stuff so if your familiar with that
> (know where to put the sources and spec file, etc) you can
> just run 'rpmbuild --ba' on the spec file manually.
>
> I'm currently running on FC10 using an RPM I built using
> the sipxecs build system with the patch below to update the
> sipxecs rpm to match a jan 2010 nightly tarball from the
> freeswitch project (put the tarball into the sipxfreeswitch
> 'src' directory). If you don't update the Release in
> the spec file RPM won't understand its an upgrade and you'll
> have to rpm -e the original one before rpm -i'ing the fresh
> one.
>
> I did originally set up this FC10 box using the 'ede'
> method (with all the paths in /etc), the only problem this
> caused was some interference with files in /selinux and of
> course apache being restarted with a sipx configuration
> (which is to be expected in retrospect, though I wish they
> had just supplied a conf.d/ file for apache instead of
> taking over the whole thing).
>
> -Eric
>
> d3 ~/sip1/main$ svn diff
> Index: lib/freeswitch/freeswitch.spec.in
> ===================================================================
> --- lib/freeswitch/freeswitch.spec.in
> (revision 17593)
> +++ lib/freeswitch/freeswitch.spec.in
> (working copy)
> @@ -8,7 +8,7 @@
> License: MPL
> Group:
> Productivity/Telephony/Servers
> Version: 1.0.5
> -Release: 15901
> +Release: 16111
> URL: http://www.freeswitch.org/
> Packager: SIPFoundry <[email protected]>
> (original by Michal Bielicki)
> Vendor: http://www.sipfoundry.org (original by
> http://www.voiceworks.pl/)
> Index: lib/freeswitch/src/freeswitch-1.0.5.tar.gz
> ===================================================================
> Cannot display: file marked as a binary type.
> svn:mime-type = application/octet-stream
> Index: lib/freeswitch/Makefile.am
> ===================================================================
> --- lib/freeswitch/Makefile.am (revision
> 17593)
> +++ lib/freeswitch/Makefile.am (working
> copy)
> @@ -1,5 +1,5 @@
> VERSION = 1.0.5
> -RELEASE = 15901
> +RELEASE = 16111
>
> SRC_DIR = $(srcdir)/src
> SRC_TARBALL = $(SRC_DIR)/freeswitch-$(VERSION).tar.gz
> @@ -25,7 +25,7 @@
> build-rpms:
> tar -xzf $(SRC_TARBALL) -C
> @RPMBUILD_TOPDIR@/SOURCES
> # cp $(SRC_DIR)/bootstrap.sh
> @RPMBUILD_TOPDIR@/SOURCES/freeswitch-$(VERSION)
> - mv -f
> @RPMBUILD_TOPDIR@/SOURCES/freeswitch-$(VERSION)
> @RPMBUILD_TOPDIR@/SOURCES/sipx-freeswitch-$(VERSION)
> + mv -f
> @RPMBUILD_TOPDIR@/SOURCES/freeswitch-$(VERSION)-20100101-0400
> @RPMBUILD_TOPDIR@/SOURCES/sipx-freeswitch-$(VERSION)
> pushd @RPMBUILD_TOPDIR@/SOURCES
> && tar -czf $(PATCHED_SRC_TARBALL)
> sipx-freeswitch-$(VERSION) && rm -rf
> sipx-freeswitch-$(VERSION) && popd
> cp $(SRC_SPEC_FILE)
> @RPMBUILD_TOPDIR@/SPECS/
> QA_RPATHS=0x0003 rpmbuild -ba --target
> @rpm_target_a...@-none-linux
> @RPMBUILD_TOPDIR@/SPECS/$(SRC_SPEC_FILE)
>
>
> On Jan 7, 2010, at 3:09 PM, George Niculae wrote:
> > Please advise if there is a way to install
> sipx-freeswitch on FC10.
> >
Thanks for the guidance, I'll let you know how's going.
George
_______________________________________________
sipx-dev mailing list [email protected]
List Archive: http://list.sipfoundry.org/archive/sipx-dev
Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-dev
sipXecs IP PBX -- http://www.sipfoundry.org/
