I'm thinking this is really a procedural thing. I believe there might be a step on the fxs device to complete a transfer successfully. It might also be possible to alter the transfer code in the fxs device but mostly I just use the fxo devices as pstn gateways. ============================ Tony Graziano, Manager Telephone: 434.984.8430 Fax: 434.984.8431
Email: [email protected] LAN/Telephony/Security and Control Systems Helpdesk: Telephone: 434.984.8426 Fax: 434.984.8427 Helpdesk Contract Customers: http://www.myitdepartment.net/gethelp/ ----- Original Message ----- From: Tony Graziano <[email protected]> To: [email protected] <[email protected]>; [email protected] <[email protected]> Sent: Mon Jul 12 19:33:00 2010 Subject: Re: [sipx-users] Actual call transfer, should it work? (polycom -> patton) I've never done this with an fxs port. The queatuion I have is when you do a trnasger initiated from an fxs device, how do you know it is referred or blind? A trace would be helpful. ============================ Tony Graziano, Manager Telephone: 434.984.8430 Fax: 434.984.8431 Email: [email protected] LAN/Telephony/Security and Control Systems Helpdesk: Telephone: 434.984.8426 Fax: 434.984.8427 Helpdesk Contract Customers: http://www.myitdepartment.net/gethelp/ ----- Original Message ----- From: [email protected] <[email protected]> To: [email protected] users <[email protected]> Sent: Mon Jul 12 19:29:12 2010 Subject: [sipx-users] Actual call transfer, should it work? (polycom -> patton) [see the bottom for versions] When I receive a call on a subscribed FXS line on a patton 4114 I can flash and make a 2nd call. The patton manual states that if I then hang up on the second call the first call should 'transfer' to the destination. I've been unable to make this work between FXS ports on the same patton and between a patton fxs and polycom 650's. I flash, get dialtone, call another extension and talk to it normally, but when I hang up the original caller hears only silence and isn't disconnected. This fails the same if the call is from a patton FXO gateway (another box), another FXS port on the same 4114, or from sipxbridge (voip.ms), or from a Polycom phone. I've tried with the target being a polycom or another FXS on the 4114. I do have the 'call-transfer' option enabled on the FXS interface in the patton. The polycoms do 'referred' and 'blind' transfer as expected in all the above scenarios (call from patton FXS, FXO, ITSP/sipxbridge, or another polycom). I will run traces next, just curious if normal call transfer has ever been known to work with Patton FXS ports or am I just wasting my time? This is sipxecs 4.2. Polycom: 0711224145|app1 |3|00|Application, load: Type=SIP, Version=3.2.3.1734 22-Mar-10 15:56 Patton fxo+fxs: Software Version : R5.4 2009-11-18 H323 SIP FXS FXO Thanks, -Eric _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users sipXecs IP PBX -- http://www.sipfoundry.org/ _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users sipXecs IP PBX -- http://www.sipfoundry.org/
