Falae Alisson! Eu já tive esse problema aqui... resolvi alterando as permissões do dispositivo mesmo! Note: /dev/cdrom é um link para o dispositvo IDE/SCSI do seu cdrom...
O que vc deve verificar eh o device que corresponde ao seu CDROM/DVD No meu caso, meus HD's são SATA e meu DVD é IDE, logo... alterei o "/dev/hda"... pode ser que seja isso... []'s Luiz Silva mailto:[EMAIL PROTECTED] UIN #33923099 Skype: luizmsrj Linux User #324589 Machine ID #262370 MSN: [EMAIL PROTECTED] "May the force be with you !!!" ----- Mensagem original ---- De: Alisson Ceolin <[EMAIL PROTECTED]> Para: [email protected] Enviadas: Terça-feira, 9 de Outubro de 2007 13:49:45 Assunto: [slack-users] Re: Slack 12 não monta pendrive ou CD/DVD ja faz parte deste grupo... não adiantou... to sem ideias.. Bruno Gomes <[EMAIL PROTECTED]> escreveu: voce tb está no grupo cdrom? o /dev/cdrom está neste grupo vc deve está tb para poder usa-lo :P 2007/10/8, Alisson Ceolin <[EMAIL PROTECTED] >:tenho notado que o muita gente não esta pesquisando, antes de perguntar as coisas.. não leve a mal.. mas... pra saber o que era o HAL, era so usar o google (HAL linux) http://www.freedesktop.org/wiki/Software/hal quando forem duvidas mais focadas, é mais interessante de responder. nao pretendo gerar flames, ok? ja q estamos falando de montagem automatica, eu tb tenho um problema e não encontrei solução ainda pen drive -> monta automaticamente, com usuarios normais e como root CD / DVD -> monta somente como root, com usuarios normais da erro de permissões... ja adicionei os usuarios no grupo plugdev, alterei permissões das pastas /mnt/dvd mnt/cdrom etc, etc.. alguém tem alguma ideia do q causa o problema? Obrigado Carlos Eduardo Maiolino < [EMAIL PROTECTED]> escreveu: Pessoal, só uma dúvida minha agora... O que é HAL ??? On 10/5/07, Gustavo T. Ludwig < [EMAIL PROTECTED] > wrote: Amigos, Instalei o Slack 12 e recompilei o Kernel com um .config que tinha salvo do Kernel 2.6.21 que veio no Slack 12 RC1. O HAL não está montando automaticamente nem o meu pendrive nem mídias CD/DVD. Fuçando atrás da solução instalei o pmount, mas não tive sucesso. Segue o dmesg depois de ter espetado o pendrive e o slack "montá-lo" 64 early_node_map[1] active PFN ranges 0: 0 -> 262064 On node 0 totalpages: 262064 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 255 pages used for memmap HighMem zone: 32433 pages, LIFO batch:7 DMI 2.3 present. ACPI: RSDP 000FA880, 0021 (r2 ACPIAM) ACPI: XSDT 3FFB0100, 003C (r1 A M I OEMXSDT 10000513 MSFT 97) ACPI: FACP 3FFB0290, 00F4 (r3 A M I OEMFACP 10000513 MSFT 97) ACPI: DSDT 3FFB03F0, 391B (r1 A0277 A0277001 1 MSFT 100000D) ACPI: FACS 3FFC0000, 0040 ACPI: APIC 3FFB0390, 0052 (r1 A M I OEMAPIC 10000513 MSFT 97) ACPI: OEMB 3FFC0040, 003F (r1 A M I OEMBIOS 10000513 MSFT 97) ACPI: PM-Timer IO Port: 0x808 Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000) Built 1 zonelists. Total pages: 260017 Kernel command line: auto BOOT_IMAGE=Slack12 ro root=802 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2203.044 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1033192k/1048256k available (3845k kernel code, 14428k reserved, 1072k data, 224k init, 130752k highmem) virtual kernel memory layout: fixmap : 0xfffeb000 - 0xfffff000 ( 80 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc05d0000 - 0xc0608000 ( 224 kB) .data : 0xc04c17a5 - 0xc05cda34 (1072 kB) .text : 0xc0100000 - 0xc04c17a5 (3845 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4409.27 BogoMIPS (lpj=2204638) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. CPU: AMD Athlon(tm) 64 Processor 3500+ stepping 02 Checking 'hlt' instruction... OK. ACPI: Core revision 20070126 ACPI: setting ELCR to 0200 (from 0c20) NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: enabled onboard AC97/MC97 devices Boot video device is 0000:01: 00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:08: ioport range 0x680-0x6ff has been reserved pnp: 00:08: ioport range 0x290-0x297 has been reserved pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved pnp: 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved pnp: 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved pnp: 00:0c: iomem range 0xc0000-0xdffff could not be reserved pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:0c: iomem range 0x100000-0x3ffeffff could not be reserved Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: faf00000-fbffffff PREFETCH window: e0000000-f9ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). NTFS driver 2.1.28 [Flags: R/W]. SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 1536k, total 262144k vesafb: mode is 1024x768x8, linelength=1024, pages=3 vesafb: protected mode interface info at c000:e2e0 vesafb: pmi: set display start = c00ce316, set palette = c00ce380 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device vga16fb: initializing vga16fb: mapped to 0xc00a0000 fb1: VGA16 VGA frame buffer device input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SLPB] Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: VIA VLink IRQ fixup for 0000:00:0f.1, from 255 to 11 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: HL-DT-STDVD-RAM GSA-H22N, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 sata_via 0000:00:0f.0: version 2.1 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 sata_via 0000:00:0f.0: routed to hard irq line 10 ata1: SATA max UDMA/133 cmd 0x0001d000 ctl 0x0001c802 bmdma 0x0001b800 irq 10 ata2: SATA max UDMA/133 cmd 0x0001c400 ctl 0x0001c002 bmdma 0x0001b808 irq 10 scsi0 : sata_via ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ATA: abnormal status 0x7F on port 0x0001d007 ATA: abnormal status 0x7F on port 0x0001d007 ata1.00: ATA-7: ST3250620NS, 3.AEG , max UDMA/133 ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 scsi1 : sata_via ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x0001c407 scsi 0:0:0:0: Direct-Access ATA ST3250620NS 3.AE PQ: 0 ANSI: 5 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 has_svm: svm not available kvm: no hardware support ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: irq 5, io mem 0xfae00000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected 116x: driver isp116x-hcd, 03 Nov 2005 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00: 10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00: 10.1: irq 11, io base 0x0000d800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 10, io base 0x0000e000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00: 10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: irq 10, io base 0x0000e400 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 rtc_cmos: probe of 00:02 failed with error -16 i2c /dev entries driver Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). ALSA device list: No soundcards found. IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions tunl0: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions NET: Registered protocol family 17 NET: Registered protocol family 15 powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00) powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x6 powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x8 powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 Using IPI Shortcut mode drivers/rtc/hctosys.c: unable to open rtc device (rtc0) input: ImPS/2 Generic Wheel Mouse as /class/input/input4 Unable to load NLS charset utf8 UDF-fs: No VRS found XFS mounting filesystem sda2 Ending clean XFS mount for filesystem: sda2 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 224k freed Linux agpgart interface v0.102 (c) Dave Jones ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 skge 1.10 addr 0xfac00000 irq 10 chip Yukon-Lite rev 9 skge eth0: addr 00:13:d4:8d:d0:08 agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 256M @ 0xd0000000 ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00: 11.5 to 64 sk98lin: driver has been replaced by the skge driver and is scheduled for removal nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007 Adding 257032k swap on /dev/sda3. Priority:-1 extents:1 across:257032k kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. skge eth0: enabling interface ADDRCONF(NETDEV_UP): eth0: link is not ready skge eth0: Link is up at 100 Mbps, full duplex, flow control both ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01: 00.0 into 8x mode spurious 8259A interrupt: IRQ7. usb 1-6: new high speed USB device using ehci_hcd and address 2 usb 1-6: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2 SCSI device sdb: 1971200 512-byte hdwr sectors (1009 MB) sdb: Write Protect is off sdb: Mode Sense: 0b 00 00 08 sdb: assuming drive cache: write through SCSI device sdb: 1971200 512-byte hdwr sectors (1009 MB) sdb: Write Protect is off sdb: Mode Sense: 0b 00 00 08 sdb: assuming drive cache: write through sdb: sdb1 sd 2:0:0:0: Attached scsi removable disk sdb sd 2:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete Unable to load NLS charset iso8859-1 FAT: IO charset iso8859-1 not found Unable to load NLS charset iso8859-1 FAT: IO charset iso8859-1 not found [EMAIL PROTECTED]:~$ idéias são bem vindas! Obrigado de ante-mão, Gustavo | ^ ^ Linux _____________________ Abra sua conta no Yahoo! Mail, o único sem limite de espaço para armazenamento! -- Bruno Gomes | ^ ^ Linux _____________________ Abra sua conta no Yahoo! Mail, o único sem limite de espaço para armazenamento! Abra sua conta no Yahoo! Mail, o único sem limite de espaço para armazenamento! http://br.mail.yahoo.com/ --~--~---------~--~----~------------~-------~--~----~ GUS-BR - Grupo de Usuários de Slackware Brasil http://www.slackwarebrasil.org/ http://groups.google.com/group/slack-users-br -~----------~----~----~----~------~----~------~--~---
