Mas não dessa forma. Voce pode ter subido como rota padrao (default gw) tem que subir apenas a rota mesmo.. sem identificar como padrão.
Regards 2011/7/13 DNK <[email protected]>: > vou trocar a placa de rede depois pra ver se melhora a lentidao > > abraçao > > Linux user number 526795 - http://counter.li.org/ > > > > 2011/7/13 DNK <[email protected]> >> >> se eu nao colocar a rota, nao consigo nem pingar, ja testei isso, do jeito >> q ta ai funciona, o problema eh a lnetidao, um amigo meu me falou q pode ser >> por causa de driver, q ele ja passou por algo assim, e o problema era >> driver. >> >> >> Linux user number 526795 - http://counter.li.org/ >> >> >> >> 2011/7/13 Alisson Ceolin <[email protected]> >>> >>> na verdade, talvez vc nem necessite adicionar a segunda rota, quando >>> configurei a interface via ifconfig ele adicionou uma entrada no route. >>> >>> >>> Alisson Ceolin >>> >>> _ >>> °v° >>> /(S)\ SLACKWARE >>> ^ ^ Linux >>> _____________________ >>> ________________________________ >>> De: Alisson Ceolin <[email protected]> >>> Para: "[email protected]" <[email protected]> >>> Enviadas: Quarta-feira, 13 de Julho de 2011 11:16 >>> Assunto: Re: [slack-users] problemas com rota >>> >>> criei algo similar aqui, mas nao notei problemas. roda um tcpdump >>> capturando tudo e depois analisa no wireshark pra ver se encontra algo >>> anomalo >>> vc esta usando ipv6? caso contrario, remove o modulo adicionando ele >>> no blacklist. >>> >>> a lentidão que percebeste é em relacao a que tipo de serviço? vc percebe >>> lentidao em ping? >>> vou deixar ativo pra ver se noto algum problema. >>> >>> root@u134358:/home/alissonc# ifconfig >>> eth0 Link encap:Ethernet HWaddr 00:1c:c0:5a:cf:bd >>> inet addr:172.16.26.25 Bcast:172.16.255.255 Mask:255.255.0.0 >>> inet6 addr: fe80::21c:c0ff:fe5a:cfbd/64 Scope:Link >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:140306399 errors:0 dropped:236 overruns:0 frame:0 >>> TX packets:5827098 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 txqueuelen:1000 >>> RX bytes:13647994551 (12.7 GiB) TX bytes:2029709930 (1.8 GiB) >>> Interrupt:20 Memory:d0300000-d0320000 >>> >>> eth1 Link encap:Ethernet HWaddr 00:01:03:e4:cf:dc >>> inet addr:10.17.201.201 Bcast:10.17.255.255 Mask:255.255.0.0 >>> inet6 addr: fe80::201:3ff:fee4:cfdc/64 Scope:Link >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:38739 errors:0 dropped:237 overruns:1 frame:0 >>> TX packets:13 errors:0 dropped:0 overruns:0 carrier:1 >>> collisions:0 txqueuelen:1000 >>> RX bytes:2360898 (2.2 MiB) TX bytes:996 (996.0 B) >>> Interrupt:17 Base address:0xa000 >>> >>> lo Link encap:Local Loopback >>> inet addr:127.0.0.1 Mask:255.0.0.0 >>> inet6 addr: ::1/128 Scope:Host >>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>> RX packets:163 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 txqueuelen:0 >>> RX bytes:34690 (33.8 KiB) TX bytes:34690 (33.8 KiB) >>> >>> root@u134358:/home/alissonc# route add -net 10.17.0.0/16 gw 10.17.1.2 >>> root@u134358:/home/alissonc# route -n >>> Kernel IP routing table >>> Destination Gateway Genmask Flags Metric Ref Use >>> Iface >>> 172.16.0.0 0.0.0.0 255.255.0.0 U 0 0 0 >>> eth0 >>> 10.17.0.0 10.17.1.2 255.255.0.0 UG 0 0 0 >>> eth1 >>> 10.17.0.0 0.0.0.0 255.255.0.0 U 0 0 0 >>> eth1 >>> 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 >>> lo >>> 0.0.0.0 172.16.0.7 0.0.0.0 UG 1 0 0 >>> eth0 >>> root@u134358:/home/alissonc# ping 10.17.1.2 >>> PING 10.17.1.2 (10.17.1.2) 56(84) bytes of data. >>> 64 bytes from 10.17.1.2: icmp_req=1 ttl=64 time=2.08 ms >>> 64 bytes from 10.17.1.2: icmp_req=2 ttl=64 time=0.491 ms >>> ^C >>> --- 10.17.1.2 ping statistics --- >>> 2 packets transmitted, 2 received, 0% packet loss, time 1001ms >>> rtt min/avg/max/mdev = 0.491/1.286/2.081/0.795 ms >>> root@u134358:/home/alissonc# ping 10.17.0.20 >>> PING 10.17.0.20 (10.17.0.20) 56(84) bytes of data. >>> From 10.17.1.2: icmp_seq=1 Redirect Host(New nexthop: 10.17.0.20) >>> 64 bytes from 10.17.0.20: icmp_req=1 ttl=64 time=6.41 ms >>> 64 bytes from 10.17.0.20: icmp_req=2 ttl=64 time=0.378 ms >>> From 10.17.1.2: icmp_seq=2 Redirect Host(New nexthop: 10.17.0.20) >>> 64 bytes from 10.17.0.20: icmp_req=3 ttl=64 time=0.429 ms >>> From 10.17.1.2: icmp_seq=3 Redirect Host(New nexthop: 10.17.0.20) >>> 64 bytes from 10.17.0.20: icmp_req=4 ttl=64 time=0.513 ms >>> From 10.17.1.2: icmp_seq=4 Redirect Host(New nexthop: 10.17.0.20) >>> ^C >>> --- 10.17.0.20 ping statistics --- >>> 4 packets transmitted, 4 received, 0% packet loss, time 3001ms >>> rtt min/avg/max/mdev = 0.378/1.934/6.419/2.589 ms >>> >>> >>> >>> >>> Alisson Ceolin >>> >>> _ >>> °v° >>> /(S)\ SLACKWARE >>> ^ ^ Linux >>> _____________________ >>> ________________________________ >>> De: DNK <[email protected]> >>> Para: [email protected] >>> Enviadas: Quarta-feira, 13 de Julho de 2011 11:01 >>> Assunto: Re: [slack-users] problemas com rota >>> >>> assim funciona: >>> >>> root@ornitorinco:~# ifconfig >>> eth0 Link encap:Ethernet HWaddr 20:cf:30:bc:87:9a >>> inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 >>> inet6 addr: fe80::22cf:30ff:febc:879a/64 Scope:Link >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:8389427 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:4383085 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 txqueuelen:1000 >>> RX bytes:3608754653 (3.3 GiB) TX bytes:260800692 (248.7 MiB) >>> Interrupt:26 Base address:0xe000 >>> >>> eth1 Link encap:Ethernet HWaddr 00:e0:7d:f8:f1:80 >>> inet addr:192.168.4.226 Bcast:192.168.4.255 >>> Mask:255.255.255.0 >>> inet6 addr: fe80::2e0:7dff:fef8:f180/64 Scope:Link >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:2188881 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:1308846 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 txqueuelen:1000 >>> RX bytes:181777178 (173.3 MiB) TX bytes:1968969842 (1.8 GiB) >>> Interrupt:19 Base address:0xec00 >>> >>> lo Link encap:Local Loopback >>> inet addr:127.0.0.1 Mask:255.0.0.0 >>> inet6 addr: ::1/128 Scope:Host >>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>> RX packets:25 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 txqueuelen:0 >>> RX bytes:2312 (2.2 KiB) TX bytes:2312 (2.2 KiB) >>> >>> root@ornitorinco:~# route -n >>> Kernel IP routing table >>> Destination Gateway Genmask Flags Metric Ref Use >>> Iface >>> 192.168.4.0 0.0.0.0 255.255.255.0 U 0 0 0 >>> eth1 >>> 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 >>> eth0 >>> 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 >>> lo >>> 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 >>> eth0 >>> >>> >>> problema eh q a rede 192.168.1.0 fica mto lento >>> >>> Linux user number 526795 - http://counter.li.org/ >>> >>> >>> >>> 2011/7/13 Alisson Ceolin <[email protected]> >>> >>> poste o ifconfig e depois de adicionar a rota para a segunda rede, poste >>> o route -n >>> >>> >>> >>> Alisson Ceolin >>> >>> _____________________ >>> ________________________________ >>> De: Denilson Guedes Duarte <[email protected]> >>> Para: [email protected] >>> Enviadas: Quarta-feira, 13 de Julho de 2011 10:30 >>> Assunto: Re: [slack-users] problemas com rota >>> >>> quais os serviços que a rede 192.168.1.0/24 nçao consegue mais acessar? >>> >>> esse servidor vai ser usado para que? >>> >>> Denilson Guedes Duarte >>> Bnet - Provedor de Internet >>> MSN/Email [email protected] >>> Fone +55 55 3411 6350 >>> Uruguaiana - RS - Brasil >>> >>> From: DNK >>> Sent: Wednesday, July 13, 2011 9:27 AM >>> To: [email protected] >>> Subject: [slack-users] problemas com rota >>> >>> estou com um problema de rota, vou tentar descrever o cenario aqui >>> >>> tenho um servidor com duas placas de rede: >>> eth0 --> 192.168.1.2 >>> eth1 --> 192.168.4.226 >>> >>> sao duas redes distintas que nao tem comunicaçao uma com a outra os >>> respectivos gateways sao: 192.168.1.1 e 192.168.4.1 >>> >>> preciso que esse servidor seja enchergado pelas duas redes e que faça >>> conexao em outras maquinas da rede da eth1 >>> >>> >>> se eu dou os seguintes comandos: >>> route add -net 192.168.4.0/24 gw 192.168.4.1 >>> route add default gw 192.168.1.1 >>> >>> ele funciona normalmente mas a rede192.168.1.0 nao consegue acessar mais >>> os serviços dele >>> se eu removo a rota pra rede route del -net 192.168.4.0/24 gw 192.168.4.1 >>> >>> volta a funcionar normalmente a conexao das maquinas da rede 192.168.1.0, >>> mas porem eu nao consigo mais conecar dele em nenhuma das maquinas da rede >>> 192.168.4.0 >>> >>> >>> Linux user number 526795 - http://counter.li.org/ >>> >>> -- >>> GUS-BR - Grupo de Usuários de Slackware Brasil >>> http://www.slackwarebrasil.org/ >>> http://groups.google.com/group/slack-users-br >>> >>> Antes de perguntar: >>> http://www.istf.com.br/perguntas/ >>> >>> Para sair da lista envie um e-mail para: >>> [email protected] >>> -- >>> GUS-BR - Grupo de Usuários de Slackware Brasil >>> http://www.slackwarebrasil.org/ >>> http://groups.google.com/group/slack-users-br >>> >>> Antes de perguntar: >>> http://www.istf.com.br/perguntas/ >>> >>> Para sair da lista envie um e-mail para: >>> [email protected] >>> >>> -- >>> GUS-BR - Grupo de Usuários de Slackware Brasil >>> http://www.slackwarebrasil.org/ >>> http://groups.google.com/group/slack-users-br >>> >>> Antes de perguntar: >>> http://www.istf.com.br/perguntas/ >>> >>> Para sair da lista envie um e-mail para: >>> [email protected] >>> >>> -- >>> GUS-BR - Grupo de Usuários de Slackware Brasil >>> http://www.slackwarebrasil.org/ >>> http://groups.google.com/group/slack-users-br >>> >>> Antes de perguntar: >>> http://www.istf.com.br/perguntas/ >>> >>> Para sair da lista envie um e-mail para: >>> [email protected] >>> >>> -- >>> GUS-BR - Grupo de Usuários de Slackware Brasil >>> http://www.slackwarebrasil.org/ >>> http://groups.google.com/group/slack-users-br >>> >>> Antes de perguntar: >>> http://www.istf.com.br/perguntas/ >>> >>> Para sair da lista envie um e-mail para: >>> [email protected] >>> >>> -- >>> GUS-BR - Grupo de Usuários de Slackware Brasil >>> http://www.slackwarebrasil.org/ >>> http://groups.google.com/group/slack-users-br >>> >>> Antes de perguntar: >>> http://www.istf.com.br/perguntas/ >>> >>> Para sair da lista envie um e-mail para: >>> [email protected] > > -- > GUS-BR - Grupo de Usuários de Slackware Brasil > http://www.slackwarebrasil.org/ > http://groups.google.com/group/slack-users-br > > Antes de perguntar: > http://www.istf.com.br/perguntas/ > > Para sair da lista envie um e-mail para: > [email protected] -- GUS-BR - Grupo de Usuários de Slackware Brasil http://www.slackwarebrasil.org/ http://groups.google.com/group/slack-users-br Antes de perguntar: http://www.istf.com.br/perguntas/ Para sair da lista envie um e-mail para: [email protected]
