Sigo pesquisando esse problema e tenho essa saida para o comando
/etc/rc.d/rc.inet1.conf. Achei estranho a linha com "yes" para o dhpc. No
sistema 13.37 de voces esta assim mesmo, pois perco justamente o nameserver
no resolv.conf apos o reboot?
*# /etc/rc.d/rc.inet1.conf
*#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").
# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.
# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.
#
=============================================================================
# Config information for eth0:
IPADDR[0]="201.37.x.xxx"
NETMASK[0]="255.255.255.0"
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""
# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""
# Config information for eth2:
IPADDR[2]=""
ETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""
# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""
# Default gateway IP address:
GATEWAY="201.37.x.xxx"
# Change this to "yes" for debugging output to stdout. Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"
## Example config information for wlan0. Uncomment the lines you need and
fill
## in your info. (You may not need all of
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
#WLAN_ESSID[4]=BARRIER05
WLAN_RATE[4]="54M auto"
##WLAN_CHANNEL[4]="auto"
##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
##WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set
WPAPSK=96389dc66eaf7e6efd5b5523ae43c
7925ff4df2f8b7099495192d44a774fda16"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="ndiswrapper"
## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0" # Use a different interface name nstead of
# the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
#MTU[4]="" # The default MTU is 1500, but you might need
# 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
# server
#WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameterthese for
your wireless network)
#IFNAME[4]="wlan0"
#IPADDR[4]=""
#NETMASK[4]=""
*#USE_DHCP[4]="yes"
*#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP
server to change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
# server
#WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameter
# defined in rc.wireless.conf, by prepending
# 'WLAN_' to the parameter's name. Useful for
# those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set
WPAPSK=thekey"
# Some drivers require a private ioctl to be
# set through the iwpriv command. If more than
# one is required, you can place them in the
# IWPRIV parameter (separated with the pipe (|)
# character, see the example).
2011/8/3 LopanRS <[email protected]>
> Tava olhando o vector 7 RC que tem como base o slack 13.37 e tambem
> tem um arquivo de nome /etc/modpbrobe.d/network.conf que contem:
> alias eth0 via-rhine
>
>
> On 3 ago, 00:06, Alcir <[email protected]> wrote:
> > Abro essa duvida apos diversos testes e em resposta ao amigo Lopan
> > esclareco:
> >
> > *Olá Alcir.
> > Ip voce pode setar editando o arquivo /etc/rc.d/rc.inet1
> > Como por exemplo pra deixar fixo o IP na interface eth0:
> >
> > DEVICE='eth0'* *
> > DHCP='no'
> > IPADDR='192.168.2.1'
> > NETMASK='255.255.255.0'
> > GATEWAY=''*
> > *PROBE='no'
> > *
> > Tenho um sistema 13.37 instalado numa placa mae Asus A8V-MX. Transportei
> o
> > hd para outra placa de mesmo modelo e editei o *
> >
> > # /etc/udev/rules.d/70-persistent-net.rules* ( name para eth0 )
> >
> > apos configurar o ip via com as alternativas *
> >
> > # netconfig
> >
> > * ou manualmente com *
> >
> > #ifconfig eth0 201.37.x.xxx netmask 255.255.255.0 up*
> >
> > tenho conex'ao com a internet.* Porem apos o reboot eu perco o ip*.
> >
> > O modulo esta carregado e certifico com:
> >
> > *#depmod -a* ( nehuma saida )
> >
> > *#lspci* ( mostra-me via_rhine e mii como ethernet )
> >
> > *#lsmod *( parte da saida )
> > Module Size Used by
> > vboxnetadp 6727 0
> > ...
> > via_rhine 17845 0
> > mii 3334 1 via_rhine
> > ipv6 236629 14
> > *
> > # dmesg *( onde encontrei coisas que desconheco )
> >
> > [ 0.235872] pci 0000:00:13.0: PCI bridge to [bus 04-04]
> > [ 0.236004] pci 0000:00:13.0: bridge window [io 0xf000-0x0000] (disabled)
> > [ 0.236009] pci 0000:00:13.0: bridge window [mem 0xfbf00000-0xfbffffff]
> > [ 0.236015] pci 0000:00:13.0: bridge window [mem 0xfff00000-0x000fffff
> pref]
> > (disabled)
> > [ 0.236080] pci 0000:00:13.1: PCI bridge to [bus 05-05] (subtractive
> decode)
> > [ 0.236179] pci 0000:00:13.1: bridge window [io 0xf000-0x0000] (disabled)
> > [ 0.236184] pci 0000:00:13.1: bridge window [mem 0xfff00000-0x000fffff]
> > (disabled)
> > [ 0.236190] pci 0000:00:13.1: bridge window [mem 0xfff00000-0x000fffff
> pref]
> > (disabled)
> > [ 0.236194] pci 0000:00:13.1: bridge window [io 0x0000-0xffff]
> (subtractive
> > decode)
> > [ 0.236197] pci 0000:00:13.1: bridge window [mem 0x000a0000-0x000bffff]
> > (subtractive decode)
> > [ 0.236201] pci 0000:00:13.1: bridge window [mem 0x20000000-0xffffffff]
> > (subtractive decode)
> > [ 0.236224] pci_bus 0000:00: on NUMA node 0
> > [ 0.236228] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> > [ 0.236382] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
> > [ 0.236412] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
> > [ 0.236498] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> > [ 0.236529] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT]
> > [ 0.236566] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP0._PRT]
> > [ 0.249347] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14
> 15)
> > [ 0.250064] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14
> 15)
> > [ 0.250769] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 10 11 12 14
> 15)
> > [ 0.251468] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14
> 15)
> > [ 0.252187] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14
> 15)
> > *0, disabled.
> > [ 0.253043] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14
> 15)
> > *0, disabled.
> > [ 0.253884] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14
> 15)
> > *0, disabled.
> > [ 0.254707] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14
> 15)
> > [ 0.255411] HEST: Table is not found!
> >
> > ...
> > [ 0.310611] RPC: Registered tcp NFSv4.1 backchannel transport module.
> > [ 0.310711] pci 0000:00:00.0: MSI quirk detected; MSI disabled
> > [ 0.310827] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
> > [ 0.310925] pci 0000:00:02.0: MSI quirk detected; subordinate MSI
> disabled
> >
> > ...
> >
> > [ 4.192627] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
> > [ 4.192784] via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) ->
> IRQ
> > 23
> > [ 4.202762] rtc_cmos 00:02: RTC can wake from S4
> > [ 4.203527] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
> > [ 4.203661] rtc0: alarms up to one year, y3k, 114 bytes nvram
> > [ 4.204425] eth0: VIA Rhine II at 0xf8fff800, 00:11:d8:01:23:45, IRQ 23.
> > [ 4.205234] eth0: MII PHY found at address 1, status 0x786d advertising
> 01e1
> >
> > ...
> >
> > [ 11.692128] EXT4-fs (sda6): mounted filesystem with ordered data mode.
> > Opts: (null)
> > [ 13.986540] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> > [ 15.200684] NET: Registered protocol family 10
> > [ 15.200937] lo: Disabled Privacy Extensions
> > [ 25.938014] eth0: no IPv6 routers present
> > [ 46.132279] vboxdrv: Found 1 processor cores.
> > [ 46.135986] vboxdrv: TSC mode is 'synchronous', kernel timer mode is
> > 'normal'.
> > [ 46.135991] vboxdrv: Successfully loaded version 4.0.8_OSE (interface
> > 0x00180000).
> > [ 55.690230] start_kdeinit (2089): /proc/2089/oom_adj is deprecated,
> please
> > use /proc/2089/oom_score_adj instead
> >
> > *Curiosamente, o comando */etc/rc.d/rc.inet1 eth0_start em rc.d/rc.local
> > n'ao funciona logo apos o reboot. Mas no console faz o ping para o
> servidor
> > funcionar.* Alguma ideia?
> > *
>
> --
> GUS-BR - Grupo de Usuários de Slackware Brasil
> http://www.slackwarebrasil.org/
> http://groups.google.com/group/slack-users-br
>
> Antes de perguntar:
> http://www.istf.com.br/perguntas/
>
> Para sair da lista envie um e-mail para:
> [email protected]
>
--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br
Antes de perguntar:
http://www.istf.com.br/perguntas/
Para sair da lista envie um e-mail para:
[email protected]
