Sending this again but with Yinka on the CC. My original mail is nowhere to be found :(
On Wed, Aug 29, 2012 at 10:26 AM, Aaron Knister <[email protected]>wrote: > Hi Yinka, > > I've tried to send a couple e-mails this morning to the list and they > didn't seem to make it so I apologize for duplicate messages. > > I set up the cluster you're working on and have periodically jumped in to > help out over the years. Usually this problem results from communication > failures between the headnode and the compute nodes. Can you send along the > output of sinfo? Can you also attempt to resolve each compute node's name > from the head node (ie dig @localhost bluefish1). Ensure you can resolve > every compute node by name, then attempt to ping them. > > Best, > Aaron > > > On Wed, Aug 29, 2012 at 9:59 AM, Yinka Adeosun <[email protected] > > wrote: > >> A few seconds**** >> >> ** ** >> >> *From:* Andy Riebs [mailto:[email protected]] >> *Sent:* Wednesday, August 29, 2012 9:26 AM >> *To:* slurm-dev >> *Subject:* [slurm-dev] RE: sview problem, was Re: Output and Error Files* >> *** >> >> ** ** >> >> On the sview problem, how long does sview report an incorrect state: a >> few seconds, a few minutes, until slurm is restarted? >> >> **** >> >> On 08/28/2012 01:24 PM, Yinka Adeosun wrote:**** >> >> I started here less than a week but I’d answer to the best of my >> knowledge.**** >> >> **** >> >> **1. **What version of SLURM? (If you configured and built it, >> what options did you use?) – 2.1.6-1 >> 2. What OS? What hardware? – RHEL5. Dell Clusters(HPC) >> 3. Are user directories shared across the cluster? --- Yes >> 4. Do you use automount for the user directories? -- Yes >> 5. Can you include a copy of your slurm.conf? --- Yes, attached >> 6. Do you know where the user output *is* going? –Created where the job >> is run >> 7. Do the slurmctld.log and slurmd.log log files report any errors? Yes >> like from nodes “…unable to register: unable to contact slurm >> controller (connect failure) >> >> >> **** >> >> Thanks,**** >> >> Yinka**** >> >> **** >> >> *From:* Andy Riebs [mailto:[email protected] <[email protected]>] >> *Sent:* Tuesday, August 28, 2012 10:50 AM >> *To:* slurm-dev >> *Subject:* [slurm-dev] Re: Output and Error Files**** >> >> **** >> >> Yinka, >> >> The following information would help considerably in identifying the >> nature of your problem: >> >> 1. What version of SLURM? (If you configured and built it, what options >> did you use?) >> 2. What OS? What hardware? >> 3. Are user directories shared across the cluster? >> 4. Do you use automount for the user directories? >> 5. Can you include a copy of your slurm.conf? >> 6. Do you know where the user output *is* going? >> 7. Do the slurmctld.log and slurmd.log log files report any errors? >> >> Andy**** >> >> On 08/28/2012 09:55 AM, Yinka Adeosun wrote:**** >> >> Hi,**** >> >> **** >> >> I am having issue with slurm not creating the output(xxx.out) and error >> (xxx.err) file In the directory it was run. Also, sview reporting that the >> job is running but it’s actually not running.**** >> >> **** >> >> Yinka Adeosun**** >> >> Unix Administrator**** >> >> Vistronix, Inc**** >> >> Contractor to US EPA Chesapeake Bay Program Office**** >> >> 410-295-1323**** >> >> **** >> >> >> >> >> **** >> >> -- **** >> >> Andy Riebs**** >> >> Hewlett-Packard Company**** >> >> High Performance Computing**** >> >> +1-786-263-9743**** >> >> My opinions are not necessarily those of HP**** >> >> [image: Image removed by sender.]**** >> >> >> >> **** >> >> -- **** >> >> Andy Riebs**** >> >> Hewlett-Packard Company**** >> >> High Performance Computing**** >> >> +1-786-263-9743**** >> >> My opinions are not necessarily those of HP**** >> >> [image: Image removed by sender.]**** >> > >
<<image001.jpg>>
<<image002.jpg>>
