True I only have 2-3 areas with hubs one at a both the repeater sites... and I think one at a client location and that is it. The rest are either behind a router or a few plugged right into the radio..
----- Original Message ----- From: "The Wirefree Network" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, October 17, 2003 1:12 PM Subject: RE: [smartBridges] Length out of range numbers HUBS are BAD!! Bad I say....BAD, BAD, BAD!! Hubs are for cheapos who cant afford freaking switches. Come on now MARTIN...get with it!! You know better than that. Hahahaha! BTW...this is exactly why I keep telling everyone to install ROUTERS behind EVERY install. There is NO need to transmit everyone's internal traffic out on the wireless side if it doesn't need to be there!! Routers on the Ethernet side of all my clients completely eliminated collisions/errors! Some may say, "I don't want to add the cost of a router." But I say, "What is your time worth?" You will spend MORE time troubleshooting, and your clients will spend more time complaining, if you don't!! My 2 cents... Sully -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Colin Watson Sent: Friday, October 17, 2003 12:44 PM To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Length out of range numbers Just out of interest, have you ensured none of your customers are connecting there airbridges through hubs? Thing is, I've seen this, if a client connects an Airbridge to a hub (which he/she can do and it will work because it fowards ~64? MAC's under it's own), then assuming they start copying data to the PC across the hall, you suddenly find the network will lock solid - especially as you appear to have no router between your canopy backhaul and access points. It's all because hubs, being passive or active repeaters, just see an electrical signal and amplify it, spitting it out through all ports. As the traffic is not destined for any node on the AP, it just gets forwarded until it hits the nearest broadcast segementation wall, normally your router (A tcpdump of your switches traffic may allude to the answer). If I were you, I'd lay out my network something like this (apologies if you already have something similar and I have misread your posts): To Another Tower (Same config as below) | APPO ---- SWITCH <-----> ROUTER (FreeBSD we use) <--------> CANOPY <====VPN (Optional) =====> CANOPY <------> ROUTER <-------> Internet | | | APPO ------ To Another Tower (Same config as above) SWITCH ---- Administrative Subnet (Mail/DNS etc) The advantages to this model are complete broadcast storm proofing from other towers (I'm assuming you have more then one?), easy scalability, and advantages Routing protocols bring - i.e. link redundency. The disadvantages are you need to segment your network logically, allocating a different subnet for each tower (This is okay if you are NAT'ing as your gonna have the whole 10.x.y.z, 192.168.x.y, 172.Something.x.y ranges at your disposal). If it's public facing IP's your using you'd need to plan perhaps more conserviatly (/25 (127) address into blocks of - 32 address per subnet (30 usable, /27) maybe?). Another area you might explore is VLAN's, my experience with these is fairly low, but it is possible I believe to segment your network work at Layer 2 (The MAC layer - which switches operate on, and broadcast storms tend to occur) logically by VLAN grouping - so you wouldn't need to split your subnets. Anyway just some ideas, hope they are helpful. Kind Regards Colin. ----- Original Message ----- From: "Blazen Wireless" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, October 17, 2003 8:00 PM Subject: Re: [smartBridges] Length out of range numbers > Not me I get one user downloading a file or something at say 100-500kbps and > it ties up that one APPO and affects the WHOLE network so no one can ping or > surf very well on another leg of e switch? seems kind of ODD to me.. > ----- Original Message ----- > From: "Sam" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Friday, October 17, 2003 12:07 PM > Subject: Re: [smartBridges] Length out of range numbers > > > I have over 30 customers each on two APPOs which seem to handle it just > fine (that is, when the APPO is still running.) The only problem I have > seen is sometimes the APPO just stops, and the blue light starts blinking > steadily off and on, off and on, and I'm unable to log into the device any > further, even through the wire. But I've gotten to the point when that > happens I put up another one. (Tired of troubleshooting them.) The only > problem is reassociating everyone (Not all of my customers have the > roaming option.) > > Anyhow, they seem to handle at least 30 users without problem. > > Sam > > On Fri, 17 Oct 2003, > Blazen Wireless wrote: > > > the APPO goes into a D-link switch with another APPO and a canopy radio > > which is set to 10 1/2 duplex. The canopy is flawless and has no errors at > > all! its always the APPO that comes back with errors? I see dingle defer > > errors and an occasion CTS error I tried swapping the switch to a 10 meg > hub > > and it made no difference I just think the APPOs cant handle the load of 9 > > customers on all the time it just craps out.. > > > > Each customer that I add on seems to make the system ore and more > unstable! > > I was under the impression these radios would handle a lot of clients > radios > > talking to it but I guess now. I am going to have to go with something > > else.. > > > > > > The XO is way out of range, I have all the bandwidth and access control I > > need at the NOC no need for it in the radio.. > > > > ----- Original Message ----- > > From: "Lars Gaarden" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Friday, October 17, 2003 11:22 AM > > Subject: Re: [smartBridges] Length out of range numbers > > > > > > Blazen Wireless wrote: > > > > > What exactly is controlling this number is this > > > good or bad? I assume bad I rebooted the appo > > > yesterday and am seeing these since about 12pm > > > PT yesterday to the tune of about 23,500? > > > > LengthOutOfRangeRx is one of the ethernet counters. > > > > According to Cisco, the meaning is: > > > > "Length out of range > > Incremented for each frame received where the 802.3 > > length field in the packet did not match the number > > of bytes actually received." > > > > What is connected to the aPPO on the ethernet side? > > Do you see any other ethernet error counters that are > > unusually high? (CRC, False carrier, Under/Oversize) > > > > > > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > > ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
