Hi
Just an entry for the hard drive database
It's a seagate hybrid hard drive in a Sony Vaio SZ650 notebook.
Mike
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST91608220AS
Serial Number: 5MA65Q7T
Firmware Version: 3.ALE
User Capacity: 160,041,885,696 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Aug 22 15:23:43 2008 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 426) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 111) minutes.
SCT capabilities: (0x0001) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail Always
- 0
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always
- 1467
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always
- 8626533990
9 Power_On_Hours 0x0032 099 099 000 Old_age Always
- 1603
10 Spin_Retry_Count 0x0013 100 100 034 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always
- 1198
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 098 098 000 Old_age Always
- 2
190 Airflow_Temperature_Cel 0x0022 061 050 045 Old_age Always
- 39 (Lifetime Min/Max 24/39)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 891
193 Load_Cycle_Count 0x0032 084 084 000 Old_age Always
- 33217
194 Temperature_Celsius 0x0022 039 050 000 Old_age Always
- 39 (0 17 0 0)
195 Hardware_ECC_Recovered 0x001a 073 061 000 Old_age Always
- 198599961
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline
- 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 10 hours (0 days + 10 hours)
When the command that caused the error occurred, the device was in standby
mode.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 51 06 00 00 00 ef Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 90 03 c0 00 00 ef 00 02:59:04.999 SET FEATURES [Reserved for Serial
ATA]
ef 90 00 c0 00 00 ef 04 02:59:04.998 SET FEATURES [Reserved for Serial
ATA]
e0 00 00 00 00 00 a0 00 02:59:04.998 STANDBY IMMEDIATE
e7 00 00 00 00 00 a0 00 02:59:04.989 FLUSH CACHE
35 00 08 f8 02 db e0 00 02:59:04.989 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 1603 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
