found on smartmontools-support.
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: HTS421212H9AT00
Serial Number: HKA410ALGBS0VB
Firmware Version: HA4OA70S
User Capacity: 120,034,123,776 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1
Local Time is: Tue May 27 18:03:52 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x04) Offline data collection activity
was suspended by an interrupting
command from host.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 89) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always -
0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline -
0
3 Spin_Up_Time 0x0007 118 118 033 Pre-fail Always -
2
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always -
2845
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always -
0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always -
0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline -
0
9 Power_On_Hours 0x0012 091 091 000 Old_age Always -
4344
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always -
0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always -
1618
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always -
0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always -
95
193 Load_Cycle_Count 0x0012 083 083 000 Old_age Always -
173295
194 Temperature_Celsius 0x0002 112 112 000 Old_age Always -
49 (Lifetime Min/Max 12/60)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always -
4
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always -
0
SMART Error Log Version: 1
ATA Error Count: 29 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 29 occurred at disk power-on lifetime: 4322 hours (180 days + 2 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 00 09 4f c2 a0 Error: IDNF
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d6 01 09 4f c2 a0 00 07:48:20.900 SMART WRITE LOG
b0 d5 01 09 4f c2 a0 00 07:48:20.700 SMART READ LOG
b0 d1 01 01 4f c2 a0 00 07:48:20.700 SMART READ ATTRIBUTE THRESHOLDS
[OBS-4]
b0 d0 01 00 4f c2 a0 00 07:48:20.700 SMART READ DATA
b0 da 00 00 4f c2 a0 00 07:48:20.700 SMART RETURN STATUS
Error 28 occurred at disk power-on lifetime: 4321 hours (180 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 59 01 0b e5 6f e0 Error: UNC at LBA = 0x006fe50b = 7333131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 0b e5 6f e0 02 06:14:18.800 READ SECTOR(S) EXT
24 00 01 0a e5 6f e0 02 06:14:18.800 READ SECTOR(S) EXT
24 00 01 09 e5 6f e0 02 06:14:18.800 READ SECTOR(S) EXT
24 00 01 08 e5 6f e0 02 06:14:18.800 READ SECTOR(S) EXT
24 00 01 07 e5 6f e0 02 06:14:18.800 READ SECTOR(S) EXT
Error 27 occurred at disk power-on lifetime: 4321 hours (180 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f5 0b e5 6f e0 Error: UNC at LBA = 0x006fe50b = 7333131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 00 00 00 6f e0 02 06:13:48.500 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6e e0 02 06:13:47.600 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6d e0 02 06:13:46.600 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6c e0 02 06:13:45.700 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6b e0 02 06:13:44.700 READ VERIFY SECTOR(S) EXT
Error 26 occurred at disk power-on lifetime: 4315 hours (179 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 59 01 0b e5 6f e0 Error: UNC at LBA = 0x006fe50b = 7333131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 0b e5 6f e0 02 00:23:00.500 READ SECTOR(S) EXT
24 00 01 0a e5 6f e0 02 00:23:00.500 READ SECTOR(S) EXT
24 00 01 09 e5 6f e0 02 00:23:00.500 READ SECTOR(S) EXT
24 00 01 08 e5 6f e0 02 00:23:00.500 READ SECTOR(S) EXT
24 00 01 07 e5 6f e0 02 00:23:00.500 READ SECTOR(S) EXT
Error 25 occurred at disk power-on lifetime: 4315 hours (179 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 f5 0b e5 6f e0 Error: UNC at LBA = 0x006fe50b = 7333131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 00 00 00 00 6f e0 02 00:22:29.700 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6e e0 02 00:22:28.800 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6d e0 02 00:22:27.800 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6c e0 02 00:22:26.900 READ VERIFY SECTOR(S) EXT
42 00 00 00 00 6b e0 02 00:22:25.900 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Selective offline Completed without error 00% 4322 -
# 2 Short offline Completed without error 00% 4316 -
# 3 Extended offline Completed: read failure 90% 4310 7333131
# 4 Extended offline Completed: read failure 90% 4309 7333131
# 5 Short offline Completed without error 00% 4308 -
# 6 Extended offline Completed: read failure 90% 4306 7333131
# 7 Short offline Completed without error 00% 4306 -
Warning! SMART Selective Self-Test Log Structure error: invalid SMART
checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
