found on smartmontools-support.
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: TOS MK4019GAXB SUN40G
Serial Number: 73LO0009T
Firmware Version: FB000C
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Oct 7 11:46:22 2005 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
*SMART overall-health self-assessment test result: PASSED*
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 342) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED
RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 2064
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 891
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 33
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 063 063 000 Old_age Always - 14830
10 Spin_Retry_Count 0x0033 117 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 846
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 146
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 3592
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 33
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 2
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 131
222 Loaded_Hours 0x0032 085 085 000 Old_age Always - 6075
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 172
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
*ATA Error Count: 42 (device log contains only the most recent five errors)*
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 42 occurred at disk power-on lifetime: 14830 hours (617 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
* 40 51 fa e8 3b ea e2 Error: UNC 250 sectors at LBA = 0x02ea3be8 = 48905192
*
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e2 3b ea e2 00 00:07: 16.295 READ DMA
ef 03 42 01 00 00 e0 00 00:07:15.861 SET FEATURES [Set transfer mode]
ff ff ff ff ff ff ff 0c 00:00:00.000 [VENDOR SPECIFIC]
c8 00 40 e2 3c ea e2 00 00:07:15.822 READ DMA
c8 00 00 e2 3b ea e2 00 00:07:09.028 READ DMA
Error 41 occurred at disk power-on lifetime: 14830 hours (617 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
*40 51 fa e8 3b ea e2 Error: UNC 250 sectors at LBA = 0x02ea3be8 = 48905192
*
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e2 3b ea e2 00 00:07:09.028 READ DMA
ef 03 42 01 00 00 e0 00 00:07: 08.594 SET FEATURES [Set transfer mode]
ff ff ff ff ff ff ff 0c 00:00:00.000 [VENDOR SPECIFIC]
c8 00 40 e2 3c ea e2 00 00:07:08.555 READ DMA
c8 00 00 e2 3b ea e2 00 00:07:01.695 READ DMA
Error 40 occurred at disk power-on lifetime: 14830 hours (617 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
*40 51 fa e8 3b ea e2 Error: UNC 250 sectors at LBA = 0x02ea3be8 = 48905192*
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e2 3b ea e2 00 00:07:01.695 READ DMA
ef 03 42 01 00 00 e0 00 00:07: 01.261 SET FEATURES [Set transfer mode]
ff ff ff ff ff ff ff 0c 00:00:00.000 [VENDOR SPECIFIC]
c8 00 40 e2 3c ea e2 00 00:07:01.221 READ DMA
c8 00 00 e2 3b ea e2 00 00:06:53.980 READ DMA
Error 39 occurred at disk power-on lifetime: 14830 hours (617 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
* 40 51 fa e8 3b ea e2 Error: UNC 250 sectors at LBA = 0x02ea3be8 = 48905192
*
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e2 3b ea e2 00 00:06:53.980 READ DMA
ef 03 42 01 00 00 e0 00 00:06:53.546 SET FEATURES [Set transfer mode]
ff ff ff ff ff ff ff 0c 00:00: 00.000 [VENDOR SPECIFIC]
c8 00 40 e2 3c ea e2 00 00:06:53.510 READ DMA
c8 00 00 e2 3b ea e2 00 00:06:46.561 READ DMA
Error 38 occurred at disk power-on lifetime: 14830 hours (617 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
*40 51 fa e8 3b ea e2 Error: UNC 250 sectors at LBA = 0x02ea3be8 = 48905192
*
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e2 3b ea e2 00 00:06:46.561 READ DMA
ef 03 42 01 00 00 e0 00 00:06:46.127 SET FEATURES [Set transfer mode]
ff ff ff ff ff ff ff 0c 00:00:00.000 [VENDOR SPECIFIC]
c8 00 40 e2 3c ea e2 00 00:06: 46.088 READ DMA
c8 00 00 e2 3b ea e2 00 00:06:39.230 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
