Hitachi Deskstar 7K3000, 7200 RPM, 64 MB buffer, SATA 6 Gbps, 2TB: http://www.hitachigst.com/internal-drives/desktop/deskstar/deskstar-7k3000
I'm putting the values of a broken disk thinking that it might be more interesting than a working one. If it's not good, I can send the values for 2 other similar working drives. Cheers, Cristian Ciupitu [root@hermes ~]# smartctl -a /dev/disk/by-id/ata-Hitachi_HDS723020BLA642_MN1221F30289BA smartctl 5.40 2010-10-16 r3189 [x86_64-redhat-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: Hitachi HDS723020BLA642 Serial Number: MN1221F30289BA Firmware Version: MN6OA180 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Wed Mar 23 20:05:01 2011 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (19808) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 1 2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 85 3 Spin_Up_Time 0x0007 168 168 024 Pre-fail Always - 362 (Average 319) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 13 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 133 133 020 Pre-fail Offline - 27 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 73 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 13 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 13 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 13 194 Temperature_Celsius 0x0002 214 214 000 Old_age Always - 28 (Min/Max 20/31) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 4 SMART Error Log Version: 1 ATA Error Count: 4 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 occurred at disk power-on lifetime: 72 hours (3 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ec 00 00 00 00 00 a0 00 00:00:30.494 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 00:00:30.494 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 00:00:30.494 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:00:30.493 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:00:30.368 IDENTIFY DEVICE Error 3 occurred at disk power-on lifetime: 72 hours (3 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ec 00 00 00 00 00 a0 00 00:00:25.098 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 00:00:25.098 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 00:00:25.097 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:00:25.097 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:00:25.097 IDENTIFY DEVICE Error 2 occurred at disk power-on lifetime: 72 hours (3 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 07 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 00 00 00 40 00 00:00:24.780 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:00:24.776 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:00:24.776 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:00:24.775 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 00:00:24.775 SET FEATURES [Set transfer mode] Error 1 occurred at disk power-on lifetime: 72 hours (3 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ec 00 01 00 00 00 a0 00 00:00:09.394 IDENTIFY DEVICE 00 8a 01 01 00 00 00 ff 00:00:09.388 NOP [Reserved subcommand] 00 8a 01 01 00 00 00 ff 00:00:07.781 NOP [Reserved subcommand] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 72 - # 2 Extended offline Completed without error 00% 58 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ------------------------------------------------------------------------------ Fulfilling the Lean Software Promise Lean software platforms are now widely adopted and the benefits have been demonstrated beyond question. Learn why your peers are replacing JEE containers with lightweight application servers - and what you can gain from the move. http://p.sf.net/sfu/vmware-sfemails _______________________________________________ Smartmontools-database mailing list Smartmontools-database@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/smartmontools-database
