Using smartctl 5.42 it tolds me it is not in smartctl database
BTW: Those weird 6 Errors always existed on this disk, disk had already more
than 96h runtime after purchasing it
smartctl 5.42 2011-10-20 r3458 [x86_64-linux-3.1.2] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3000JD-98KLB0
Serial Number: WD-WMAMR1578341
Firmware Version: 08.05J08
User Capacity: 300.069.052.416 bytes [300 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Dec 5 01:51:03 2011 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command
from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 116) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x001f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0003 205 188 021 Pre-fail Always
- 4733
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always
- 1296
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always
- 0
9 Power_On_Hours 0x0032 063 063 000 Old_age Always
- 27016
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always
- 1182
194 Temperature_Celsius 0x0022 115 093 000 Old_age Always
- 35
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0009 200 199 051 Pre-fail Offline
- 0
SMART Error Log Version: 1
ATA Error Count: 6 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 occurred at disk power-on lifetime: 12 hours (0 days + 12 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 f7 3f 2e e0 Error: UNC 8 sectors at LBA = 0x002e3ff7 = 3031031
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 f7 3f 2e 06 68 12:49:51.375 READ DMA EXT
25 00 00 f7 40 2e 06 68 12:49:51.285 READ DMA EXT
25 00 00 a7 aa b7 06 68 12:49:51.270 READ DMA EXT
25 00 f8 ff 3f 2e 06 68 12:49:51.225 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:48.825 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 12 hours (0 days + 12 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f7 3f 2e e0 Error: UNC at LBA = 0x002e3ff7 = 3031031
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 f7 3f 2e 06 68 12:49:48.825 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:46.800 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:44.420 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:42.025 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:39.635 READ DMA EXT
Error 4 occurred at disk power-on lifetime: 12 hours (0 days + 12 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f7 3f 2e e0 Error: UNC at LBA = 0x002e3ff7 = 3031031
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 f7 3f 2e 06 68 12:49:46.800 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:44.420 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:42.025 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:39.635 READ DMA EXT
25 00 60 8f 3f 2e 06 68 12:49:39.630 READ DMA EXT
Error 3 occurred at disk power-on lifetime: 12 hours (0 days + 12 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f7 3f 2e e0 Error: UNC at LBA = 0x002e3ff7 = 3031031
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 f7 3f 2e 06 68 12:49:44.420 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:42.025 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:39.635 READ DMA EXT
25 00 60 8f 3f 2e 06 68 12:49:39.630 READ DMA EXT
25 00 00 a7 a8 b7 06 68 12:49:39.620 READ DMA EXT
Error 2 occurred at disk power-on lifetime: 12 hours (0 days + 12 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f7 3f 2e e0 Error: UNC at LBA = 0x002e3ff7 = 3031031
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 f7 3f 2e 06 68 12:49:42.025 READ DMA EXT
25 00 00 f7 3f 2e 06 68 12:49:39.635 READ DMA EXT
25 00 60 8f 3f 2e 06 68 12:49:39.630 READ DMA EXT
25 00 00 a7 a8 b7 06 68 12:49:39.620 READ DMA EXT
25 00 08 ef 3f 2e 06 68 12:49:39.610 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 27016 -
# 2 Extended offline Completed without error 00% 23138 -
# 3 Extended offline Completed without error 00% 22594 -
# 4 Extended offline Interrupted (host reset) 30% 22512 -
# 5 Extended offline Completed without error 00% 18593 -
# 6 Extended offline Completed without error 00% 13815 -
# 7 Extended offline Completed without error 00% 11989 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
------------------------------------------------------------------------------
All the data continuously generated in your IT infrastructure
contains a definitive record of customers, application performance,
security threats, fraudulent activity, and more. Splunk takes this
data and makes sense of it. IT sense. And common sense.
http://p.sf.net/sfu/splunk-novd2d
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
