Hi, by default, my new external USB drive isn't recognized:
# smartctl -a /dev/sdd smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.4] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net Smartctl open device: /dev/sdd [USB JMicron] failed: No device connected Adding the '-d sat' options remedies that issue, though: smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.4] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST1000DM005 HD103SJ Serial Number: S246J9EC348385 LU WWN Device Id: 5 0004cf 20724e000 Firmware Version: 1AJ100E5 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 6 Local Time is: Fri Sep 21 18:23:54 2012 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART STATUS RETURN: incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9360) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 156) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0 2 Throughput_Performance -OS--K 056 056 000 - 8536 3 Spin_Up_Time PO---K 072 071 025 - 8746 4 Start_Stop_Count -O--CK 100 100 000 - 18 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 28 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 8 191 G-Sense_Error_Rate -O---K 252 252 000 - 0 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 044 000 - 35 (Min/Max 28/56) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 0 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 19 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 2 sectors [Extended self-test log] GP Log at address 0x08 has 2 sectors [Power Conditions log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP Log at address 0xbb has 4 sectors [Device vendor specific log] GP Log at address 0xbc has 2 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 25 - # 2 Short offline Completed without error 00% 22 - # 3 Extended offline Completed without error 00% 2 - # 4 Short offline Completed without error 00% 0 - Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 34/35 Celsius Lifetime Min/Max Temperature: 20/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (87) Index Estimated Time Temperature Celsius 88 2012-09-21 07:45 50 ******************************* 89 2012-09-21 07:50 51 ******************************** 90 2012-09-21 07:55 50 ******************************* ... ..( 21 skipped). .. ******************************* 112 2012-09-21 09:45 50 ******************************* 113 2012-09-21 09:50 51 ******************************** 114 2012-09-21 09:55 51 ******************************** 115 2012-09-21 10:00 51 ******************************** 116 2012-09-21 10:05 50 ******************************* 117 2012-09-21 10:10 50 ******************************* 118 2012-09-21 10:15 51 ******************************** ... ..( 11 skipped). .. ******************************** 2 2012-09-21 11:15 51 ******************************** 3 2012-09-21 11:20 50 ******************************* 4 2012-09-21 11:25 50 ******************************* 5 2012-09-21 11:30 49 ****************************** 6 2012-09-21 11:35 49 ****************************** 7 2012-09-21 11:40 48 ***************************** ... ..( 2 skipped). .. ***************************** 10 2012-09-21 11:55 48 ***************************** 11 2012-09-21 12:00 47 **************************** ... ..( 14 skipped). .. **************************** 26 2012-09-21 13:15 47 **************************** 27 2012-09-21 13:20 48 ***************************** 28 2012-09-21 13:25 49 ****************************** 29 2012-09-21 13:30 50 ******************************* 30 2012-09-21 13:35 52 ********************************* 31 2012-09-21 13:40 52 ********************************* 32 2012-09-21 13:45 53 ********************************** 33 2012-09-21 13:50 54 *********************************** 34 2012-09-21 13:55 55 ************************************ 35 2012-09-21 14:00 55 ************************************ 36 2012-09-21 14:05 55 ************************************ 37 2012-09-21 14:10 56 ************************************* ... ..( 17 skipped). .. ************************************* 55 2012-09-21 15:40 56 ************************************* 56 2012-09-21 15:45 55 ************************************ 57 2012-09-21 15:50 54 *********************************** 58 2012-09-21 15:55 53 ********************************** 59 2012-09-21 16:00 52 ********************************* 60 2012-09-21 16:05 52 ********************************* 61 2012-09-21 16:10 51 ******************************** 62 2012-09-21 16:15 51 ******************************** 63 2012-09-21 16:20 50 ******************************* 64 2012-09-21 16:25 50 ******************************* 65 2012-09-21 16:30 50 ******************************* 66 2012-09-21 16:35 49 ****************************** ... ..( 2 skipped). .. ****************************** 69 2012-09-21 16:50 49 ****************************** 70 2012-09-21 16:55 48 ***************************** ... ..( 6 skipped). .. ***************************** 77 2012-09-21 17:30 48 ***************************** 78 2012-09-21 17:35 47 **************************** ... ..( 6 skipped). .. **************************** 85 2012-09-21 18:10 47 **************************** 86 2012-09-21 18:15 34 *************** 87 2012-09-21 18:20 35 **************** Error SMART WRITE LOG does not return COUNT and LBA_LOW register Warning: device does not support SCT (Get) Error Recovery Control command SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 13 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 14 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific Take care, Peter ------------------------------------------------------------------------------ Got visibility? Most devs has no idea what their production app looks like. Find out how fast your code is with AppDynamics Lite. http://ad.doubleclick.net/clk;262219671;13503038;y? http://info.appdynamics.com/FreeJavaPerformanceDownload.html _______________________________________________ Smartmontools-database mailing list Smartmontools-database@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/smartmontools-database
