Hallo,
i once the S.M.A.R.T. Data of the disk in addition to "Corsair SSD
Toolbox 1.0"
and HWinfo64 read under Windows 7. The smart log data I have again attached.
Sincerely yours Hubert
1) First, the data here of "Corsair SSD Toolbox 1.0"
(I had to type the by hand)
a)Info:
Modell Number: Corsair Neutron SSD ATA Fixed Disk
Serial Numver: (long number)
Firmware Version: M310
Drive Size: 64GB
ATA Version: Minor version is not reported (ATA8-ACS)
Features: LBA,DMA, TRIM SMART, Security, NCQ
Temperature: 32 C
Total HOST Reads: 5 GB
Total HOST Writes: 5 GB
b) Smart state:
Legende: State = (1) FAIL (2) PASS (3) INFO
State|ID |Attribut |Current Value |Threshold |Raw Value |Worts | Status
(2) |01 |Raw Read Error Rate |166 |6 |0 |166 | OK
(3) |05 |Retired Block Count |253 |36 |0 |253 | N/A
(3) |09 |Power On Hours (POH) |100 |0 |43 |100 | N/A
(3) |0C |Device Power Cycle Count |100 |20 |10 |100 | N/A
(3) |AB |Program Fail Count |253 |0 |0 |253 | N/A
(3) |AC |Erase Fail Count |253 |0 |0 |253 | N/A
(3) |B5 |Program Fail Count |253 |0 |0 |253 | N/A
(3) |B6 |Erase Fail Count |253 |0 |0 |253 | N/A
(3) |C2 |Temperature |29 |0 |29 |0 | N/A
(3) |C9 |Uncorrectable Soft Read Error Rate |100 |0 |0 |100 | N/A
(3) |CC |Soft ECC Correction Rate |100 |0 |0 |100 | N/A
(2) |E7 |SSD Life Left |253 |10 | | | OK
(3) |EA |Unknown Attribute |100 |0 | | | N/A
(3) |F1 |Lifetime GB Written |100 |0 |5 |100 | N/A
(3) |F2 |Lifetime GB Read |100 |0 |5 |100 | N/A
(3) |Fa |(ReadErrorRetryRate) |100 |0 |251 |100 | N/A
2) Here is the log of HWinfo64
Corsair Neutron SSD -------------------------------------------------------
[General Information]
Drive Controller: Serial ATA 6Gb/s
Drive Model: Corsair Neutron SSD
Drive Revision: M310
Drive Serial Number: (long number)
Drive Capacity: 61,057 MBytes (64 GB)
Drive Capacity [MB]: 61057
Media Rotation Rate: SSD Drive (Non-rotating)
[Drive Geometry]
Number of Cylinders: 16383
Number of Heads: 16
Sectors Per Track: 63
Bytes Per Sector: Unknown
Bytes Per Track: Unknown
Number Of ECC Bytes: Unknown
Number of Sectors: 16514064
Total 32-bit LBA Sectors: 125045424
Total 48-bit LBA Sectors: 125045424
Cache Buffer Size: N/A
Controller Type: Not Specified
[Transfer Modes]
Sectors Per Interrupt: Total: 16, Active: 1
Max. PIO Transfer Mode: 4
Multiword DMA Mode: Total: 2, Active: -
Singleword DMA Mode: Total: -, Active: -
Ultra-DMA Mode: Total: 6 (ATA-133), Active: 2 (Ultra-DMA/33)
Max. Multiword DMA Transfer Rate: 16.7 MBytes/s
Max. PIO with IORDY Transfer Rate: 16.7 MBytes/s
Max. PIO w/o IORDY Transfer Rate: 16.7 MBytes/s
Transfer Width: 16-bit
Native Command Queuing: Supported, Max. Depth: 32
TRIM Command: Supported (Indeterminate Read After TRIM)
[Device flags]
Fixed Drive: Present
Removable Drive: Not Present
Magnetic Storage: Present
LBA Mode: Supported
DMA Mode: Supported
IORDY: Supported
IORDY Disableable: Supported
[Features]
Write Cache: Present, Active
S.M.A.R.T. Feature: Present, Active
Security Feature: Present, Inactive
Removable Media Feature: Not Present, Disabled
Power Management: Present, Active
Advanced Power Management: Not Present, Inactive
Packet Interface: Not Present, Disabled
Look-Ahead Buffer: Present, Active
Host Protected Area: Present, Enabled
Power-Up In Standby: Not Suppported, Inactive
Automatic Acoustic Management: Not Suppported, Inactive
48-bit LBA: Supported, Active
[Self-Monitoring, Analysis and Reporting Technology (S.M.A.R.T.)]
[01] Raw Read Error Rate: 166/6, Worst: 166
[05] Reallocated Sector Count: 253/36, Worst: 253
[09] Power-On Hours/Cycle Count: 100/Always OK, Worst: 100 (Data = 43)
[0C] Power Cycle Count: 100/20, Worst: 100 (Data = 19)
[AB] Program Fail Count 253/Always OK, Worst: 253
[AC] Erase Fail Count: 253/Always OK, Worst: 253
[B5] Program Fail Count (Total)/Non-Physical Page-Aligned Access Count:
253/Always OK, Worst: 253
[B6] Erase Fail Count: 253/Always OK, Worst: 253
[C2] Temperature 31/Always OK, Worst: 0 (Data = 31.0 �C)
[C9] Total Count of Write Commands/Super Cap Status/Uncorrectable Soft
Read Error Rate 100/Always OK, Worst: 100
[CC] Bad Block Full Flag/Soft ECC Correction Rate 100/Always OK, Worst: 100
[E7] SSD Life Left: 253/10, Worst: 253
[EA] Average Erase Count, Max Erase Count: 100/Always OK, Worst: 100
(Data = 64)
[F1] Total Host Writes 100/Always OK, Worst: 100 (Data = 5)
[F2] Total Host Reads/Write Protect Progress 100/Always OK, Worst: 100
(Data = 5)
[FA] Read Error Retry Rate: 100/Always OK, Worst: 100 (Data = 251)
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.10.0-031000-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: Corsair Neutron SSD
Firmware Version: M310
User Capacity: 64.023.257.088 bytes [64,0 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Jul 6 00:41:30 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0
5 Reallocated_Sector_Ct -O--CK 253 253 036 - 0
9 Power_On_Hours -O--CK 100 100 000 - 32
12 Power_Cycle_Count -O--CK 100 100 020 - 18
171 Unknown_Attribute -O--CK 253 253 000 - 0
172 Unknown_Attribute -O--CK 253 253 000 - 0
181 Program_Fail_Cnt_Total -O--CK 253 253 000 - 0
182 Erase_Fail_Count_Total -O--CK 253 253 000 - 0
194 Temperature_Celsius -O---- 041 000 000 - 41 (Min/Max 22/47)
201 Soft_Read_Error_Rate -OSR-- 100 100 000 - 0
204 Soft_ECC_Correction -OSR-- 100 100 000 - 0
231 Temperature_Celsius PO--CK 253 253 010 - 0
234 Unknown_Attribute -O--CK 100 100 000 - 56
241 Total_LBAs_Written -O--CK 100 100 000 - 5
242 Total_LBAs_Read -O--CK 100 100 000 - 4
250 Read_Error_Retry_Rate -O--CK 100 100 000 - 239
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 4 sectors [Comprehensive SMART error log]
GP/S Log at address 0x03 has 5 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x04 has 8 sectors [Device Statistics]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 202 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 202 [1] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 01 08 17 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 01 08 17 00 00 00 40 40 00:00:39.750 SET FEATURES [Enable
APM]
c8 00 00 00 08 04 08 1f 01 08 10 e1 e1 00:00:39.750 READ DMA
c8 00 00 00 08 01 08 0f 04 08 18 e1 e1 00:00:39.750 READ DMA
c8 00 00 00 08 82 82 9f 01 08 08 e1 e1 00:00:39.730 READ DMA
c8 00 00 00 08 84 41 0f 82 82 98 e2 e2 00:00:39.730 READ DMA
Error 201 [0] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 50 3f 10 00 00 00 00 00 01 ef 08 at LBA = 0x0f000001 = 251658241
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
29 20 20 aa 55 00 00 55 05 ba aa a0 a0 00:00:30.050 READ MULTIPLE EXT
29 20 20 aa 55 00 00 55 05 ba aa a0 a0 00:00:30.060 READ MULTIPLE EXT
29 20 20 00 08 00 00 00 05 ba b8 e0 e0 00:00:27.570 READ MULTIPLE EXT
29 20 20 00 38 00 00 00 05 ba 80 e0 e0 00:00:27.550 READ MULTIPLE EXT
29 20 20 00 07 00 00 00 05 ba 79 e0 e0 00:00:27.550 READ MULTIPLE EXT
Error 200 [19] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 50 3f 10 00 00 00 00 00 01 ef 08 at LBA = 0x0f000001 = 251658241
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
29 20 20 00 05 00 00 00 00 00 62 a0 a0 00:00:05.370 READ MULTIPLE EXT
29 20 20 00 05 00 00 00 00 00 62 a0 a0 00:00:05.380 READ MULTIPLE EXT
29 20 20 00 65 00 00 00 00 00 02 e0 e0 00:00:05.350 READ MULTIPLE EXT
29 20 20 00 01 00 00 00 00 00 01 e0 e0 00:00:05.350 READ MULTIPLE EXT
29 20 20 00 01 00 00 00 00 00 00 e0 e0 00:00:05.350 READ MULTIPLE EXT
Error 199 [18] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 50 01 00 00 00 00 00 08 00 e0 08
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
f5 00 00 01 00 00 00 00 00 08 00 a0 a0 00:00:05.330 SECURITY FREEZE LOCK
f5 00 00 01 00 00 00 00 00 08 00 a0 a0 00:00:05.330 SECURITY FREEZE LOCK
f5 20 00 01 00 00 00 00 00 08 00 e0 e0 00:00:05.000 SECURITY FREEZE LOCK
e3 20 20 01 00 00 00 00 00 08 00 a0 a0 00:00:04.660 IDLE
29 20 20 00 01 00 00 00 00 08 00 e0 e0 00:00:04.660 READ MULTIPLE EXT
Error 198 [17] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
01 -- 50 00 01 00 00 00 00 00 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 ff 00 00 01 00 00 00 00 00 01 a0 a0 00:00:04.370 NOP [Abort queued
commands]
00 ff 00 00 01 00 00 00 00 00 01 a0 a0 00:00:04.380 NOP [Abort queued
commands]
Error 197 [16] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 53 76 ef 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 53 76 ef 00 00 00 40 40 00:12:54.610 SET FEATURES [Enable
APM]
c8 00 00 00 18 44 0b e7 53 76 d8 e0 e0 00:12:54.600 READ DMA
c8 00 00 00 08 80 18 ff 44 0b e0 e2 e2 00:12:54.600 READ DMA
c8 00 00 00 08 44 0b ef 80 18 f8 e2 e2 00:12:54.600 READ DMA
c8 00 00 00 08 04 15 a7 44 0b e8 e2 e2 00:12:54.600 READ DMA
Error 196 [15] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 50 3f 10 00 00 00 00 00 01 ef 08 at LBA = 0x0f000001 = 251658241
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
29 20 20 aa 55 00 00 55 05 ba aa a0 a0 00:12:46.080 READ MULTIPLE EXT
29 20 20 aa 55 00 00 55 05 ba aa a0 a0 00:12:46.090 READ MULTIPLE EXT
29 20 20 00 08 00 00 00 05 ba b8 e0 e0 00:12:43.810 READ MULTIPLE EXT
29 20 20 00 38 00 00 00 05 ba 80 e0 e0 00:12:43.800 READ MULTIPLE EXT
29 20 20 00 07 00 00 00 05 ba 79 e0 e0 00:12:43.800 READ MULTIPLE EXT
Error 195 [14] occurred at disk power-on lifetime: 31 hours (1 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 50 3f 10 00 00 00 00 00 01 ef 08 at LBA = 0x0f000001 = 251658241
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
29 20 20 00 05 00 00 00 00 00 62 a0 a0 00:12:11.880 READ MULTIPLE EXT
29 20 20 00 05 00 00 00 00 00 62 a0 a0 00:12:11.890 READ MULTIPLE EXT
29 20 20 00 65 00 00 00 00 00 02 e0 e0 00:12:11.860 READ MULTIPLE EXT
29 20 20 00 01 00 00 00 00 00 01 e0 e0 00:12:11.860 READ MULTIPLE EXT
29 20 20 00 01 00 00 00 00 00 00 e0 e0 00:12:11.860 READ MULTIPLE EXT
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 32 -
# 2 Short offline Completed without error 00% 32 -
# 3 Extended offline Completed without error 00% 2 -
Device does not support Selective Self Tests/Logging
Warning: device does not support SCT Commands
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:
Build for Windows Store.
http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
