Attached file is for a 250 GB Seagate ST250DM001, previously sold as
Samsung Spinpoint F4 HD256GJ. Note that Seagate also uses this model number
ST250DM001 for a Spinpoint F3 drive that had the Samsung model number
HD253GJ: http://samsunghdd.seagate.com/ (switch to product support tab to
see cross reference)
smartctl 5.43 2012-06-05 r3561 [i686-linux-3.4.9] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST250DM001 HD256GJ
Firmware Version: 1AR10001
User Capacity: 250.059.350.016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Fri Aug 2 22:30:40 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 2160) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 36) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 083 082 025 - 5277
4 Start_Stop_Count -O--CK 100 100 000 - 9
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 8
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 9
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 064 000 - 31 (Min/Max 23/32)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 9
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 2 sectors [Extended self-test log]
GP Log at address 0x08 has 2 sectors [Power Conditions log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error log]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 7 -
# 2 Short offline Completed without error 00% 0 -
Note: selective self-test log revision number (0) not 1 implies that no
selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been
run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 31 Celsius
Power Cycle Min/Max Temperature: 25/31 Celsius
Lifetime Min/Max Temperature: 23/59 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (80)
Index Estimated Time Temperature Celsius
81 2013-08-02 11:55 31 ************
82 2013-08-02 12:00 58 ***************************************
... ..( 2 skipped). .. ***************************************
85 2013-08-02 12:15 58 ***************************************
86 2013-08-02 12:20 59 ****************************************
87 2013-08-02 12:25 59 ****************************************
88 2013-08-02 12:30 58 ***************************************
89 2013-08-02 12:35 58 ***************************************
90 2013-08-02 12:40 29 **********
91 2013-08-02 12:45 30 ***********
92 2013-08-02 12:50 30 ***********
93 2013-08-02 12:55 31 ************
94 2013-08-02 13:00 31 ************
95 2013-08-02 13:05 32 *************
96 2013-08-02 13:10 32 *************
97 2013-08-02 13:15 31 ************
98 2013-08-02 13:20 32 *************
... ..( 3 skipped). .. *************
102 2013-08-02 13:40 32 *************
103 2013-08-02 13:45 33 **************
... ..( 3 skipped). .. **************
107 2013-08-02 14:05 33 **************
108 2013-08-02 14:10 32 *************
109 2013-08-02 14:15 32 *************
110 2013-08-02 14:20 33 **************
111 2013-08-02 14:25 33 **************
112 2013-08-02 14:30 33 **************
113 2013-08-02 14:35 32 *************
114 2013-08-02 14:40 33 **************
115 2013-08-02 14:45 33 **************
116 2013-08-02 14:50 33 **************
117 2013-08-02 14:55 34 ***************
118 2013-08-02 15:00 33 **************
119 2013-08-02 15:05 33 **************
120 2013-08-02 15:10 25 ******
121 2013-08-02 15:15 26 *******
122 2013-08-02 15:20 27 ********
123 2013-08-02 15:25 29 **********
... ..( 5 skipped). .. **********
1 2013-08-02 15:55 29 **********
2 2013-08-02 16:00 30 ***********
3 2013-08-02 16:05 29 **********
4 2013-08-02 16:10 30 ***********
... ..( 9 skipped). .. ***********
14 2013-08-02 17:00 30 ***********
15 2013-08-02 17:05 31 ************
16 2013-08-02 17:10 31 ************
17 2013-08-02 17:15 30 ***********
18 2013-08-02 17:20 30 ***********
19 2013-08-02 17:25 30 ***********
20 2013-08-02 17:30 31 ************
21 2013-08-02 17:35 30 ***********
... ..( 5 skipped). .. ***********
27 2013-08-02 18:05 30 ***********
28 2013-08-02 18:10 31 ************
29 2013-08-02 18:15 30 ***********
... ..( 7 skipped). .. ***********
37 2013-08-02 18:55 30 ***********
38 2013-08-02 19:00 31 ************
... ..( 4 skipped). .. ************
43 2013-08-02 19:25 31 ************
44 2013-08-02 19:30 30 ***********
45 2013-08-02 19:35 30 ***********
46 2013-08-02 19:40 30 ***********
47 2013-08-02 19:45 31 ************
... ..( 8 skipped). .. ************
56 2013-08-02 20:30 31 ************
57 2013-08-02 20:35 30 ***********
58 2013-08-02 20:40 31 ************
59 2013-08-02 20:45 32 *************
60 2013-08-02 20:50 32 *************
61 2013-08-02 20:55 31 ************
62 2013-08-02 21:00 31 ************
63 2013-08-02 21:05 31 ************
64 2013-08-02 21:10 32 *************
65 2013-08-02 21:15 32 *************
66 2013-08-02 21:20 32 *************
67 2013-08-02 21:25 31 ************
... ..( 3 skipped). .. ************
71 2013-08-02 21:45 31 ************
72 2013-08-02 21:50 27 ********
73 2013-08-02 21:55 28 *********
74 2013-08-02 22:00 29 **********
75 2013-08-02 22:05 30 ***********
76 2013-08-02 22:10 30 ***********
77 2013-08-02 22:15 30 ***********
78 2013-08-02 22:20 31 ************
79 2013-08-02 22:25 31 ************
80 2013-08-02 22:30 31 ************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 8 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
------------------------------------------------------------------------------
Get your SQL database under version control now!
Version control is standard for application code, but databases havent
caught up. So what steps can you take to put your SQL databases under
version control? Why should you start doing it? Read more to find out.
http://pubads.g.doubleclick.net/gampad/clk?id=49501711&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
