Please add ST120HM000-1G5142 to the DB or let me know if I need to do anything
else or submit this to a different e-mail.
Thanks,
Liz Swaffield
Associate Software Engineer
Electrosonic Inc.
Tel +1 818.333.7683 | Mobile +1 818.434.8844
3320 North San Fernando Blvd., Burbank, CA, 91504 - USA
liz.swaffi...@electrosonic.com<mailto:liz.swaffi...@electrosonic.com> |
www.electrosonic.com<http://www.electrosonic.com>
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-63-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST120HM000-1G5142
Serial Number: Z4M00TYV
LU WWN Device Id: 5 000c50 02ff325f2
Firmware Version: C675
User Capacity: 120,034,123,776 bytes [120 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Sep 8 16:58:40 2015 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 3) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 19) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -OSR-- 166 166 006 - 0
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
9 Power_On_Hours -O--CK 100 100 000 - 11
12 Power_Cycle_Count -O--CK 100 100 020 - 11
171 Unknown_Attribute -O--CK 100 100 000 - 0
172 Unknown_Attribute -O--CK 100 100 000 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 000 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 000 - 0
194 Temperature_Celsius -O---K 032 026 000 - 32 (Min/Max 23/56)
201 Unknown_SSD_Attribute -O--CK 100 100 000 - 0
204 Soft_ECC_Correction -O--CK 100 100 000 - 0
231 Temperature_Celsius PO--C- 100 100 010 - 0
234 Unknown_Attribute -O--CK 100 100 000 - 95
241 Total_LBAs_Written -O--CK 100 100 000 - 89
242 Total_LBAs_Read -O--CK 100 100 000 - 2
250 Read_Error_Retry_Rate -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x07 GPL,SL R/O 2 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa8 GPL VS 521 Device vendor specific log
0xa8 SL VS 255 Device vendor specific log
0xb7 GPL,SL VS 4 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 28 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 28 [7] occurred at disk power-on lifetime: 10 hours (0 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 01:07:04.810 SET FEATURES [Enable
APM]
60 00 08 00 c8 00 00 09 04 0b 30 40 08 01:07:04.790 READ FPDMA QUEUED
60 00 08 00 c0 00 00 09 04 11 e8 40 08 01:07:04.780 READ FPDMA QUEUED
60 00 08 00 b8 00 00 09 04 0f 48 40 08 01:07:04.780 READ FPDMA QUEUED
60 00 08 00 b0 00 00 09 04 09 a8 40 08 01:07:04.780 READ FPDMA QUEUED
Error 27 [6] occurred at disk power-on lifetime: 10 hours (0 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 10 45 00 00 00 00 00 00 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 01:06:51.780 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
ec 03 00 45 00 00 00 00 00 00 00 00 00 01:06:51.780 IDENTIFY DEVICE
ef 00 03 10 45 00 00 00 00 00 00 00 00 01:06:51.780 SET FEATURES [Set
transfer mode]
c6 03 00 0c 10 00 00 00 00 00 00 00 00 01:06:51.780 SET MULTIPLE MODE
ef 00 03 01 0c 00 00 00 00 00 00 00 00 01:06:51.780 SET FEATURES [Set
transfer mode]
Error 26 [5] occurred at disk power-on lifetime: 10 hours (0 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:56:24.000 SET FEATURES [Enable
APM]
60 00 08 00 00 00 00 01 c4 0a a8 40 08 00:56:23.990 READ FPDMA QUEUED
60 00 08 00 f0 00 00 00 00 10 00 40 08 00:56:23.940 READ FPDMA QUEUED
60 00 08 00 e8 00 00 00 00 00 20 40 08 00:56:23.940 READ FPDMA QUEUED
60 00 08 00 e0 00 00 00 00 02 00 40 08 00:56:23.940 READ FPDMA QUEUED
Error 25 [4] occurred at disk power-on lifetime: 10 hours (0 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 10 45 00 00 00 00 00 00 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 00:56:10.990 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
ec 03 00 45 00 00 00 00 00 00 00 00 00 00:56:10.990 IDENTIFY DEVICE
ef 00 03 10 45 00 00 00 00 00 00 00 00 00:56:10.990 SET FEATURES [Set
transfer mode]
c6 03 00 0c 10 00 00 00 00 00 00 00 00 00:56:10.990 SET MULTIPLE MODE
ef 00 03 01 0c 00 00 00 00 00 00 00 00 00:56:10.990 SET FEATURES [Set
transfer mode]
Error 24 [3] occurred at disk power-on lifetime: 9 hours (0 days + 9 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:16.750 SET FEATURES [Enable
APM]
60 00 20 00 e8 00 00 0c c4 45 00 40 08 00:00:16.750 READ FPDMA QUEUED
60 00 08 00 e0 00 00 09 07 f8 08 40 08 00:00:16.740 READ FPDMA QUEUED
60 00 20 00 d8 00 00 00 14 73 20 40 08 00:00:16.740 READ FPDMA QUEUED
60 00 10 00 d0 00 00 01 c4 7c a8 40 08 00:00:16.740 READ FPDMA QUEUED
Error 23 [2] occurred at disk power-on lifetime: 9 hours (0 days + 9 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 10 45 00 00 00 00 00 00 e0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ec d2 00 45 00 00 00 00 00 00 00 00 00 00:00:03.690 IDENTIFY DEVICE
b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 00:00:03.690 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
ec 03 00 45 00 00 00 00 00 00 00 00 00 00:00:03.690 IDENTIFY DEVICE
ef 00 03 10 45 00 00 00 00 00 00 00 00 00:00:03.690 SET FEATURES [Set
transfer mode]
c6 03 00 0c 10 00 00 00 00 00 00 00 00 00:00:03.690 SET MULTIPLE MODE
Error 22 [1] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:17.790 SET FEATURES [Enable
APM]
60 00 08 00 48 00 00 09 00 08 80 40 08 00:00:17.750 READ FPDMA QUEUED
60 00 08 00 40 00 00 01 c4 0a a8 40 08 00:00:17.740 READ FPDMA QUEUED
60 00 20 00 38 00 00 0c c5 4c 60 40 08 00:00:17.680 READ FPDMA QUEUED
60 00 20 00 30 00 00 0c c5 4c 40 40 08 00:00:17.680 READ FPDMA QUEUED
Error 21 [0] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 10 45 00 00 00 00 00 00 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 00:00:04.380 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
ec 03 00 45 00 00 00 00 00 00 00 00 00 00:00:04.380 IDENTIFY DEVICE
ef 00 03 10 45 00 00 00 00 00 00 00 00 00:00:04.380 SET FEATURES [Set
transfer mode]
c6 03 00 0c 10 00 00 00 00 00 00 00 00 00:00:04.380 SET MULTIPLE MODE
ef 00 03 01 0c 00 00 00 00 00 00 00 00 00:00:04.380 SET FEATURES [Set
transfer mode]
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 11 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 11 Lifetime Power-On Resets
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 9 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
------------------------------------------------------------------------------
Monitor Your Dynamic Infrastructure at Any Scale With Datadog!
Get real-time metrics from all of your servers, apps and tools
in one place.
SourceForge users - Click here to start your Free Trial of Datadog now!
http://pubads.g.doubleclick.net/gampad/clk?id=241902991&iu=/4140
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
