To whom it may concern,
My Patriot Blast 480GB SSD isn't in the smartmontools drive database. Attached is the information as requested in the WIKI. I've also attached the export of smart attributes from the Patriot SATA Toolbox v1.15 SMART attributes tab. Thanks, David
smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-win7-sp1] (sf-6.5-1)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: Patriot Blast
Firmware Version: SAFM11.3
User Capacity: 480,103,981,056 bytes [480 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Nov 23 10:11:53 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 30) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 2) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 57
9 Power_On_Hours -O--C- 100 100 000 - 9887
12 Power_Cycle_Count -O--C- 100 100 000 - 57
168 Unknown_Attribute -O--C- 100 100 000 - 0
170 Unknown_Attribute PO---- 100 100 010 - 513
173 Unknown_Attribute -O--C- 100 100 000 - 262151
192 Power-Off_Retract_Count -O--C- 100 100 000 - 30
194 Temperature_Celsius PO---K 070 070 030 - 30 (Min/Max -1/30)
218 Unknown_Attribute PO-R-- 100 100 050 - 0
231 Temperature_Celsius PO--C- 100 100 000 - 100
241 Total_LBAs_Written -O--C- 100 100 000 - 2408
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 6 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 57
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 57 [56] occurred at disk power-on lifetime: 4110 hours (171 days + 6
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 00 00 00 10 28 00 Error: UNC
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 00 10 28 00 00:35:37.753 READ LOG EXT
60 00 01 00 38 00 00 00 00 00 00 40 00 00:35:37.439 READ FPDMA QUEUED
b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:35:36.528 SMART RETURN STATUS
60 00 22 00 28 00 00 00 00 00 00 40 00 00:35:36.487 READ FPDMA QUEUED
60 00 00 00 20 00 00 37 e4 36 ae 40 00 00:35:36.487 READ FPDMA QUEUED
Error 56 [55] occurred at disk power-on lifetime: 2042 hours (85 days + 2 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 58 00 00 07 64 c4 e0 40 00 Error: UNC at LBA = 0x0764c4e0 =
124044512
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 58 00 00 07 64 c4 e0 40 00 8d+05:24:52.873 READ FPDMA QUEUED
61 00 10 00 50 00 00 00 52 40 00 40 00 8d+05:24:51.961 WRITE FPDMA QUEUED
61 00 10 00 48 00 00 00 50 dc 40 40 00 8d+05:24:51.961 WRITE FPDMA QUEUED
61 00 10 00 40 00 00 00 50 94 c0 40 00 8d+05:24:51.960 WRITE FPDMA QUEUED
61 00 10 00 38 00 00 00 50 44 b0 40 00 8d+05:24:51.960 WRITE FPDMA QUEUED
Error 55 [54] occurred at disk power-on lifetime: 1819 hours (75 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 b0 00 00 13 1f 14 f0 40 00 Error: UNC at LBA = 0x131f14f0 =
320804080
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 b0 00 00 13 1f 14 f0 40 00 3d+07:41:53.992 READ FPDMA QUEUED
61 00 10 00 a8 00 00 00 50 7f 00 40 00 3d+07:41:53.081 WRITE FPDMA QUEUED
61 00 10 00 a0 00 00 00 50 44 b0 40 00 3d+07:41:53.081 WRITE FPDMA QUEUED
61 00 10 00 98 00 00 00 50 2c 70 40 00 3d+07:41:53.081 WRITE FPDMA QUEUED
61 00 10 00 90 00 00 00 4f 59 50 40 00 3d+07:41:53.081 WRITE FPDMA QUEUED
Error 54 [53] occurred at disk power-on lifetime: 1813 hours (75 days + 13
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 80 00 00 13 1e ea 10 40 00 Error: UNC at LBA = 0x131eea10 =
320793104
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 80 00 00 13 1e ea 10 40 00 3d+01:17:02.960 READ FPDMA QUEUED
61 00 10 00 78 00 00 00 53 c1 b0 40 00 3d+01:16:52.971 WRITE FPDMA QUEUED
61 00 10 00 70 00 00 00 53 6c f0 40 00 3d+01:16:52.971 WRITE FPDMA QUEUED
61 00 10 00 68 00 00 00 53 28 c0 40 00 3d+01:16:52.971 WRITE FPDMA QUEUED
61 00 10 00 60 00 00 00 50 b6 50 40 00 3d+01:16:52.971 WRITE FPDMA QUEUED
Error 53 [52] occurred at disk power-on lifetime: 1741 hours (72 days + 13
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 40 00 00 13 1e d5 78 40 00 Error: UNC at LBA = 0x131ed578 =
320787832
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 40 00 00 13 1e d5 78 40 00 01:31:52.871 READ FPDMA QUEUED
61 00 10 00 38 00 00 00 50 7f 00 40 00 01:31:51.959 WRITE FPDMA QUEUED
61 00 10 00 30 00 00 00 50 44 b0 40 00 01:31:51.959 WRITE FPDMA QUEUED
61 00 10 00 28 00 00 00 4f 59 50 40 00 01:31:51.959 WRITE FPDMA QUEUED
61 00 10 00 20 00 00 00 4a e8 00 40 00 01:31:51.959 WRITE FPDMA QUEUED
Error 52 [51] occurred at disk power-on lifetime: 1678 hours (69 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 68 00 00 02 d8 5f b0 40 00 Error: UNC at LBA = 0x02d85fb0 =
47734704
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 68 00 00 02 d8 5f b0 40 00 21:51:52.115 READ FPDMA QUEUED
60 00 40 00 60 00 00 07 c1 15 88 40 00 21:51:50.906 READ FPDMA QUEUED
60 00 18 00 58 00 00 09 1d 19 b0 40 00 21:51:50.904 READ FPDMA QUEUED
60 00 08 00 50 00 00 08 df 2d 00 40 00 21:51:50.903 READ FPDMA QUEUED
60 00 08 00 48 00 00 07 b5 79 d8 40 00 21:51:50.900 READ FPDMA QUEUED
Error 51 [50] occurred at disk power-on lifetime: 1666 hours (69 days + 10
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 80 00 00 13 6b 51 a8 40 00 Error: UNC at LBA = 0x136b51a8 =
325800360
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 80 00 00 13 6b 51 a8 40 00 10:02:56.897 READ FPDMA QUEUED
61 00 10 00 78 00 00 00 50 44 b0 40 00 10:02:54.094 WRITE FPDMA QUEUED
61 00 10 00 70 00 00 00 4f 59 50 40 00 10:02:54.094 WRITE FPDMA QUEUED
61 00 01 00 68 00 00 00 06 40 2a 40 00 10:02:54.094 WRITE FPDMA QUEUED
61 00 01 00 60 00 00 00 06 af f0 40 00 10:02:54.094 WRITE FPDMA QUEUED
Error 50 [49] occurred at disk power-on lifetime: 1638 hours (68 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 10 00 00 00 50 1c b0 40 00 Error: UNC at LBA = 0x00501cb0 =
5250224
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 10 00 10 00 00 00 50 1c b0 40 00 5d+00:39:20.713 READ FPDMA QUEUED
61 00 08 00 08 00 00 12 72 db 78 40 00 5d+00:39:18.833 WRITE FPDMA QUEUED
61 00 08 00 00 00 00 12 6e 3e d0 40 00 5d+00:39:18.832 WRITE FPDMA QUEUED
61 00 18 00 f8 00 00 12 6a 40 30 40 00 5d+00:39:18.832 WRITE FPDMA QUEUED
60 00 10 00 f0 00 00 00 50 e1 30 40 00 5d+00:39:18.806 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 9887 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 57 --- Lifetime Power-On Resets
0x01 0x010 4 9887 --- Power-on Hours
0x01 0x018 6 5050341347 --- Logical Sectors Written
0x01 0x020 6 29443763 --- Number of Write Commands
0x01 0x028 6 3281745807 --- Logical Sectors Read
0x01 0x030 6 25957759 --- Number of Read Commands
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 2045 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 1 --- Resets Between Cmd Acceptance and
Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 32 --- Current Temperature
0x05 0x010 1 32 --- Average Short Term Temperature
0x05 0x018 1 32 --- Average Long Term Temperature
0x05 0x020 1 50 --- Highest Temperature
0x05 0x028 1 5 --- Lowest Temperature
0x05 0x030 1 50 --- Highest Average Short Term Temperature
0x05 0x038 1 16 --- Lowest Average Short Term Temperature
0x05 0x040 1 50 --- Highest Average Long Term Temperature
0x05 0x048 1 16 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 50 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 5 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 456 --- Number of Hardware Resets
0x06 0x018 4 0 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 0 --- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 38223308 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 504 Device-to-host register FISes sent due to a COMRESET
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
SMARTInfo.csv
Description: MS-Excel spreadsheet
------------------------------------------------------------------------------
_______________________________________________ Smartmontools-database mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/smartmontools-database
