Are you sure you can't see the device with "format"? Please reply the "format" output. It should show the device as something like c1t1d0 or something.
Van: David Preece [mailto:[email protected]] Verzonden: dinsdag 8 maart 2016 4:47 Aan: [email protected] Onderwerp: [smartos-discuss] Adding a new disk - too hard :( Hi, I'm trying to add a PCIe SSD to act as an L2ARC but it's not going well. The device is found at boot: 2016-03-07T23:57:39.395442+00:00 i7 sata: [ID 663010 kern.info <http://kern.info> ] /pci@0,0/pci8086,3b42@1c/pci1b4b,9230@0 : 2016-03-07T23:57:39.395446+00:00 i7 sata: [ID 761595 kern.info <http://kern.info> ] #011SATA processor (ATAPI) device at port 7 2016-03-07T23:57:39.395451+00:00 i7 sata: [ID 846691 kern.info <http://kern.info> ] #011model MARVELL VIRTUALL 2016-03-07T23:57:39.395456+00:00 i7 sata: [ID 693010 kern.info <http://kern.info> ] #011firmware 1.09 2016-03-07T23:57:39.395460+00:00 i7 sata: [ID 163988 kern.info <http://kern.info> ] #011serial number 2016-03-07T23:57:39.395465+00:00 i7 sata: [ID 594940 kern.info <http://kern.info> ] #011supported features: 2016-03-07T23:57:39.395477+00:00 i7 sata: [ID 981177 kern.info <http://kern.info> ] #011 DMA 2016-03-07T23:57:39.395495+00:00 i7 sata: [ID 514995 kern.info <http://kern.info> ] #011SATA Gen1 signaling speed (1.5Gbps) Shows up in the picl tree (abbreviated) [root@i7 /]# prtpicl / (picl, ab600000001) platform (upa, ab600000005) scsi_vhci (devctl, ab60000003f) pci (pciex, ab600000066) pci8086,3b42 (pciex, ab600000200) pci1b4b,9230 (obp-device, ab60000022a) pci1028,2da (obp-device, ab600000286) hub (obp-device, ab6000002b0) storage (obp-device, ab6000002dc) disk (block, ab60000030a) pci1028,2da (obp-device, ab600000391) disk (block, ab6000003c1) And under cfgadm (abbreviated) [root@i7 ~]# cfgadm Ap_Id Type Receptacle Occupant Condition sata0/0::dsk/c1t0d0 disk connected configured ok sata1/7 processor connected unconfigured ok usb1/1 usb-hub connected configured ok usb1/1.6 usb-storage connected configured ok sata0/0::1t0d0 is the hard drive, usb1/1.6 is presumably the USB thumb drive. But if I try to configure the disk: [root@i7 ~]# cfgadm -c configure sata1/7 cfgadm: Hardware specific failure: Failed to config device at ap_id: /devices/pci@0,0/pci8086,3b42@1c/pci1b4b,9230@0:7 devfsadm also fails to create a /dev/dsk/ entry, unsurprisingly. The device itself is a Marvell 88se9230 and is in the same family as 88se9128 which definitely has a driver: http://lists.omniti.com/pipermail/omnios-discuss/2013-July/001002.html and https://www.illumos.org/issues/3815 Problem exists as of 20160304T005100Z. I had a look for a compatibility table so I could just add new the pci id and see if it goes, but to no avail. Any ideas? Thanks, Dave smartos-discuss | <https://www.listbox.com/member/archive/184463/=now> Archives <https://www.listbox.com/member/archive/rss/184463/27966043-4eecc9e4> | <https://www.listbox.com/member/?&; 4dc> Modify Your Subscription <http://www.listbox.com> ------------------------------------------- smartos-discuss Archives: https://www.listbox.com/member/archive/184463/=now RSS Feed: https://www.listbox.com/member/archive/rss/184463/25769125-55cfbc00 Modify Your Subscription: https://www.listbox.com/member/?member_id=25769125&id_secret=25769125-7688e9fb Powered by Listbox: http://www.listbox.com
