Nice; how about the rest of us submitting their idea-jewels for something
to
do. Could make for some interesting reading for a change.
Here's a couple:
On F3x fuses with opaque (typically carbon) canopies, I machine a slot
which is
long enough to view one of those nifty battery LED's. The slot is offset
to one
side such that just prior to launch I can glance at it and not only know
PWR is
present, but where it's at.
I then Goop the LED display to the inside of the canopy. A side benefit
is that
technically, even if the canopy departs the aircraft on launch/landing it
remains tethered, thus allowing you to score on that round.
The lead material supplied on most imported F3x aircraft, it seems the
prerequisite is to find the absolute cheapest material produced by
mankind. The
awg is poor, and the insulation will depart on a hot day. One might
consider
replacing it.
The piddly switches supplied with our systems are average at best,
especially
for competition use. They have been known to fail. Simply replace the
entire
switch assembly with a 2-pin high quality bullet-type connector used to
supply
PWR to small electrics, and your servos will see higher voltage. Add to
this
that typical bullet-type connectorship has cycle rates in the 100's,
which
rivals the original slider switch.
Quoting Harley Michaelis <[EMAIL PROTECTED]>:
> That's clever, Tom. Thanks for passing it on. I lament the absence of
> neat,
> creative ideas that used to be presented by many.
>
> ----- Original Message -----
> From: "Thomas Koszuta" <[EMAIL PROTECTED]>
> To: "Harley Michaelis" <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>
> Cc: <[email protected]>
> Sent: Tuesday, August 15, 2006 7:42 AM
> Subject: Re: [RCSE] Another tip about securing a tube in an
> inaccessible
> area
>
>
> > I've done the same thing with heavy thread.
> >
> > Drill a hole of the fuse in both sides, where you want to attach the
> > tube.
>
> > Using a long upholstery needle, go into one side and out the other,
> > reverse the needle and loop the thread around the tube as you pass
> > the
> > needle back out.
> >
> > If you are sewing in a tube on both sides, you obviously need to loop
> > both
>
> > of them before sealing the holes.
> >
> > Pull the tubing up tight to the fuse side and fill the hole with
> > baking
> > soda. Hit it with thin CA, then sand flush.
> >
> > (I didn't see/read the whole thread, so if someone already suggested
> > this,
>
> > apologies.)
> >
> > Tom Koszuta
> > Western New York Sailplane and Electric Flyers
> > Buffalo, NY
> >
> > ----- Original Message -----
> > From: "Harley Michaelis" <[EMAIL PROTECTED]>
> > To: <[EMAIL PROTECTED]>
> > Cc: <[email protected]>
> > Sent: Friday, August 11, 2006 2:30 PM
> > Subject: [RCSE] Another tip about securing a tube in an inaccessible
> > area
> >
> >
> >> This applies to a translucent fuselage, such as unpainted glass. If
> >> the
> >> tube to be installed is one nothing wants to stick to, decide on the
> >> spots where you want it attached and shrink a sleeve of HS tubing
> >> at
> >> those spots on the tube.
> >>
> >> Position the tube. Just above it, drill small holes in the fuselage,
> >> such
>
> >> as 1/8", at the location of the HS pieces. Bend a common pin so it
> >> can be
>
> >> inserted into the hole to pull the tubing against the inside of the
> >> fuselage. Remove the needle from a small syringe. Put some
> >> quickepoxy in
> >> it. Let gravity help get it where wanted. Put a tiny spring clamp on
> >> the
> >> pin. Snip when the epoxy has cured.
> >>
> >>
> >> ----- Original Message -----
> >> From: <[EMAIL PROTECTED]>
> >> To: "Harley Michaelis" <[EMAIL PROTECTED]>
> >> Sent: Saturday, August 05, 2006 6:57 PM
> >> Subject: Re: [RCSE] build tip
> >>
> >>
> >>> thx, glad i can help some.
> >>>
> >>> i'm always looking for a better way, can't believe i didn't of this
> >>> a
> >>> long time ago.
> >>>
> >>> Dave Hauch
> >>> www.git-r-built.com
> >>> ----- Original Message -----
> >>> From: "Harley Michaelis" <[EMAIL PROTECTED]>
> >>> To: <[EMAIL PROTECTED]>
> >>> Sent: Saturday, August 05, 2006 7:40 PM
> >>> Subject: Re: [RCSE] build tip
> >>>
> >>>
> >>>> Good idea, Dave. Thanks for passing it on. ----- Original
> >>>> Message -----
>
> >>>> From: <[EMAIL PROTECTED]>
> >>>> To: <[email protected]>
> >>>> Sent: Saturday, August 05, 2006 4:00 PM
> >>>> Subject: [RCSE] build tip
> >>>>
> >>>>
> >>>>> here's something i just came up when gluing pushrods in long
> >>>>> skinny fuses without making a mess.
> >>>
> >>
> >> RCSE-List facilities provided by Model Airplane News. Send
> >> "subscribe"
> >> and "unsubscribe" requests to [EMAIL PROTECTED] Please
> >> note
> >> that subscribe and unsubscribe messages must be sent in text only
> >> format
> >> with MIME turned off. Email sent from web based email such as
> >> Hotmail
> >> and AOL are generally NOT in text format
> >
>
> RCSE-List facilities provided by Model Airplane News. Send "subscribe"
> and
> "unsubscribe" requests to [EMAIL PROTECTED] Please note that
> subscribe and unsubscribe messages must be sent in text only format
> with MIME
> turned off. Email sent from web based email such as Hotmail and AOL
> are
> generally NOT in text format
>
Simon Van Leeuwen
PnP Systems - The E-Harness of Choice
Radius Systems
Cogito Ergo Zoom
RCSE-List facilities provided by Model Airplane News. Send "subscribe"
and "unsubscribe" requests to [EMAIL PROTECTED] Please note
that subscribe and unsubscribe messages must be sent in text only format
with MIME turned off. Email sent from web based email such as Hotmail
and AOL are generally NOT in text format
