Still claiming to be the most-informed person on the planet about the RDS,
I'd like to explain how make an extremely simple mockup. It takes longer to
tell how than to do it.  No purchase of couplers is necessary.

Locate a flat piece of sheet something or other, ply or harder balsa, say
1/8" thick. A piece 4" wide by 15-16" long will do fine. This is a "wing
panel". Cut along a "hingeline" to make a movable surface say 1" wide. Cut
that in half to make a "flap" and an "aileron". Find some really sticky
adhesive tape and hinge the parts on the underside, spacing them so they
can freely move as though they were flaps and ailerons. . . you know, so
you can get 90 degrees down and some up on the "flap" and say 45 degrees
each way on the "aileron". Now you have a "wing panel". Never mind that the
ailerons are bottom-hinged. 

For "drive shafts" locate a 3/32" wire coat hanger and cut two straight
pieces 3" long. Make a 90 degree bend 1/2" long on one end of each. The
1/2" sections become upright "handles" to move to simulate RDS action. 

Put a low-radius 45 degree bend 3/4" long in the other end of the aileron
shaft, so that with that bend horizontal, the handle is vertical.
Similarly, put a 90 degree bend in the flap shaft. Now you have "drive
shafts."

"Pockets" will mount directly on the surfaces and consist of a 1/2" x 2"
top of 1/16" ply and 1/2" sq. spacers of 3/32" hard balsa or ply. Cut 4
spacers and 2 tops. Avoid bind, but a little slop is no problem here. 

Centered in the flap and aileron, mount the pockets so the front edge is
1/16" behind the hingeline. Epoxy all items together.

Slip the aileron drive shaft into the aileron pocket and the flap drive
shaft into the flap pocket, angled 45 degrees to the hingeline. See that
the bend in the flap shaft will go inside the pocket. Make a 45 degree
pencil line along the side of each shaft. 

Locate a piece of 3/4" common ply, etc. Nail or screw the wing to this so
you can align and secure the drive shafts with small wire nails pounded
through the wing either side of the shafts. Place the small nails about
1/2" in from the bends so they touch both sides of the shafts. 

Pick up the assembly and move the flap shaft handle. Note to get full 90
degrees down, the elbow of the bend has to be slightly behind the
hingeline. Note that 90 degrees  rotation generates 90 degrees down flap
and all kinds of reflex is available, too.  

Note that 45 degrees of rotation either way of the aileron shaft generates
45 degrees of deflection. Great for flaperons, too. Note the elbow of the
bend needs to be slightly ahead of the pocket to get the desired action.
Note how smoothly things work with the shaft vertically aligned to enter
the pocket. In the real world, this may involve mounting the servos with a
little tilt, depending on the vertical positioning of the pocket in the
surface.

Having proven to yourselves that the RDS is a viable method of moving
surfaces, show the mockup to your friends and say "Take a look at this!"
Then get some couplers and get serious about doing an installation with the
help of the RDS website. 

IMHO, there is really no excuse to put up with all the ugly created by
horns, clevises, threaded rods, etc. with this new technology available.

Harley Michaelis, LSF023,  26 S. Roosevelt, Walla Walla, WA. 99362.
(509)529-2562   RDS website: http://www.proptwisters.org/rds2/index.html


RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]

Reply via email to