Dan,

What I have done in my Shappire is this.  Make up some 1/2" K & S brass 
slugs at the increments you want to be able to add weight.  Fill with your 
weight of choice, lead shot/epoxy, tungsten powder, or melted tire weights. 
Obtain some Estes Rocket tubes, # BT-5.  These have a nominal ID of .518", 
perfect for a slip fit on the K & S tubing.  Just do a search on the Net, 
found multiple suppliers or look in a good hobby shop if you can find one 
these days.  Make a plug to close the aft end of the tube, so the slugs 
don't fly all the way to the tail feathers when inserted.  I like lite-ply, 
light weight and bonds to the tubes with thin CA like crazy.

If you want to really strengthen the tube wrap it with 1.5 oz. fiberglass 
cloth using CA.  Or, you can just soak the inside with CA.  If you CA the 
inside, you might need to ream the tube after the CA sets with a piece of 
1/2" brass tube.  I have done either and both, with both the cloth and CA 
the tubes are really STIFF and LIGHT.  That is what I just recently 
installed in my Eraser.  I recommend a brass tube collar CA'd to the paper 
tube where you plan to have a piano wire retainer to carry landing shock 
loads.  The Eraser tube weighed less than 3/8 oz. with the collar.

If you are installing this in the Sapphire I sold you and still have the pin 
type landing skeg, I would recommend two tubes.  These go either side of the 
landing skeg.  Make a bulkhead for the aft portion of the tubes and the 
forward portion of the tubes.  Install all of this in your fuselage so the 
full ballast load rests at the CG.  Don't you just love building a ship in a 
bottle?

Now make up some 3/8" hard balsa spacers to your liking so you can use less 
than the full load.  3/8" balsa will fit perfectly if you just break the 
corners.  Just make sure the spacers keep the ballast at the CG.  I will 
also recommend that if you require a balsa spacer at the retainer pin like I 
do, CA a piece of brass shim stock on the end that contacts the piano wire 
retainer pin to prevent crushing when dorking.

This is all easier to see than to write.  The next time we meet up let me 
know so I can bring my Sapphire and show how it looks.  This set-up allows 
me to carry 15.5 oz. of ballast in my Sapphire if desired.  It's not an even 
pound because I am using the slugs I made 20+ years ago.  The Eraser set-up 
carries the same load in one tube, all centered on my favorite CG.  It's 
nice having only one ballast system in the flight box for all of your 
arrows!

Mark W.

----- Original Message ----- 
From: <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Sunday, June 12, 2005 7:03 PM
Subject: [RCSE] Ballast suggestions


> Gent's
>
> I'd like to add a provision for ballast to my Sapphire.
>
> Looking for suggestions on tube/plug combinations that fit nicely.
>
> Didn't have a whole lot of luck at Home Depot.
>
> Dan
> RCSE-List facilities provided by Model Airplane News.  Send "subscribe" 
> and "unsubscribe" requests to [EMAIL PROTECTED]  Please note 
> that subscribe and unsubscribe messages must be sent in text only format 
> with MIME turned off.  Email sent from web based email such as Hotmail and 
> AOL are generally NOT in text format
> 



RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]  Please note that subscribe and 
unsubscribe messages must be sent in text only format with MIME turned off.  
Email sent from web based email such as Hotmail and AOL are generally NOT in 
text format

Reply via email to