Hello !
I'm triing to boot from a sata hard disk drive with a conBIOS 1.33 and I
need some help.
This is the normal boot with the HDD as Primary/Master
comBIOS ver. 1.33 20070103 Copyright (C) 2000-2007 Soekris Engineering.
net5501
0512 Mbyte Memory CPU Geode LX 500 Mhz
Pri Mas WDC WD2500BEVS-22VAT0 LBA Xlt 1024-255-63 134 Gbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15
0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15
1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997,1998,1999 Intel Corporation
VIA Rhine III Management Adapter v2.43 (2005/12/15)
CLIENT MAC ADDR: 00 00 24 CA 6A 04
PXE-EA0: Network boot canceled by keystroke
PXE-M0F: Exiting Intel PXE ROM.
No Boot device available, enter monitor.
comBIOS Monitor. Press ? for help.
> show
ConSpeed = 115200
ConLock = Enabled
ConMute = Disabled
BIOSentry = Enabled
PCIROMS = Enabled
PXEBoot = Disabled
FLASH = Secondary
BootDelay = 5
FastBoot = Disabled
BootPartition = 3
BootDrive = 80 81 F0 FF
ShowPCI = Enabled
Reset = Hard
CpuSpeed = Default
The comBIOS says "No Boot device available, enter monitor."
But forcing to boot from 80 .... boots perfectly
> boot 80
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 pci mem[639K 511M a20=on]
disk: hd0+
>> OpenBSD/i386 BOOT 3.01
-
com0: 115200 baud
switching console to com0
>> OpenBSD/i386 BOOT 3.01
boot>
booting hd0a:/bsd: 5913424+1004644 [52+306864+287943]=0x72a4d4
entry point at 0x200120
í
[ using 595232 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.3 (GENERIC) #698: Wed Mar 12 11:07:05 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
500 z
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 536440832 (511MB)
avail mem = 510664704 (487MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/70/03, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
......
......
Maybe I've a bad parameter set ?
What parameter/s need I configure to make the 5501 boot withot a serial
typed "boot 80" command?
Please Help needed !
Many Thanks
_______________________________________________
Soekris-tech mailing list
[email protected]
http://lists.soekris.com/mailman/listinfo/soekris-tech
