All,
 
I try to install the SpeedTouch usb on RedHat 7.1/ 2.4.7/ PII 400 according to your manu.
but failed. 
1) when the socket is inserted, the two lamp is both off.
2) left lamp is red , not green, during the bootup.
 
is there any body would do such a thing:
1) integrate its driver into  kernel.
2) make a rpm  package.
 
now its installation is not so easy that any newbie would install it.
 
Regards,
 
Richard
 
 
 

# cat /proc/bus/usb/devices
 
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=255ms
 

#dmesg
 
Linux version 2.4.7 ([EMAIL PROTECTED]) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-81)) #2 Tue Jul 24 10:33:50 CST 2001
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=2.4.7 ro root=302 BOOT_FILE=/boot/vmlinuz-2.4.7
Initializing CPU#0
Detected 400.943 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 799.53 BogoMIPS
Memory: 126868k/131072k available (922k kernel code, 3816k reserved, 325k data, 172k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU:     After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU:             Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb150, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Disabled enhanced CPU to PCI posting #2
PCI: Using IRQ router VIA [1106/0596] at 00:07.0
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: queued sectors max/low 84232kB/28077kB, 256 slots per queue
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: Maxtor 90845D4, ATA DISK drive
hdd: SAMSUNG SCR-3232, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1: unexpected interrupt, status=0x7f, count=1
ide1 at 0x170-0x177,0x376 on irq 15
hda: 16514064 sectors (8455 MB) w/512KiB Cache, CHS=1027/255/63
hdd: ATAPI 32X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hda: hda1 hda2 hda3 < hda5 hda6 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
es1371: version v0.30 time 15:43:44 Jul 23 2001
PCI: Found IRQ 10 for device 00:0a.0
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x06
es1371: found es1371 rev 6 at io 0xe800 irq 10
es1371: features: joystick 0x0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 172k freed
Adding Swap: 200772k swap-space (priority -1)
usb-uhci.c: $Revision: 1.259 $ time 15:52:07 Jul 23 2001
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.251:USB Universal Host Controller Interface driver
usb.c: USB disconnect on device 1
usb.c: USB disconnect on device 0
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
 printing eip:
c01a5122
*pde = 00000000
Oops: 0000
CPU:    0
EIP:    0010:[<c01a5122>]
EFLAGS: 00010246
eax: 00000000   ebx: c12d8ca4   ecx: c020d67d   edx: c020d67c
esi: c12b69a0   edi: c12bfe00   ebp: c12d8c60   esp: c75d9ef4
ds: 0018   es: 0018   ss: 0018
Process modprobe (pid: 218, stackpage=c75d9000)
Stack: 00000007 c02284e0 c020d5cc 00000000 00000025 c12bfe40 c12bff38 00000000
       c12bfe00 c01a62dc c020da47 c12bfe00 c01a7f7c ffffffff c12bfc04 c12bfcfc
       c7d4e9a0 c12bfc00 c01a62c0 c12bfcfc 00000018 0000000e c12d8d60 c8821ae0
Call Trace: [<c01a62dc>] [<c01a7f7c>] [<c01a62c0>] [<c01a114f>] [<c01139de>] [<c0112ec9>] [<c0106cdb>]
 
Code: 8b 40 0c 8b 50 04 89 5e 1c c7 04 24 08 00 00 00 8b 87 d0 00
hub.c: get_port_status(2) failed (err = -19)
hub.c: get_port_status(2) failed (err = -19)
hub.c: get_port_status(2) failed (err = -19)
hub.c: get_port_status(2) failed (err = -19)
hub.c: get_port_status(2) failed (err = -19)
hub.c: Cannot enable port 2 of hub 1, disabling port.
hub.c: Maybe the USB cable is bad?
hub.c: cannot disable port 2 of hub 1 (err = -19)
hub.c: get_hub_status failed
isapnp: Scanning for PnP cards...
isapnp: Card 'D-Link DE-220P PnP ISA Card'
isapnp: 1 Plug & Play card detected total
ne.c: ISAPnP reports Generic PNP at i/o 0x240, irq 5.
ne.c:v1.10 9/23/94 Donald Becker ([EMAIL PROTECTED])
Last modified Nov 1, 2000 by Paul Gortmaker

Reply via email to