I've recently installed this as a second OS on my system. I've dabbeled in Linux before, but am a real newbie really... I've done a make config and set the options I've found in a few places as below:
Code Maturity Level Options Prompt for development and/or incomplete code/drivers [Y] Loadable Module Support Enable Loadable Module Support [Y] General Setup Support for hot-pluggable devices [Y] Networking Options Packet Socket [Y] Asynchronous Transfer Mode (ATM) (EXPERIMENTAL) [Y] Network Device Support PPP (Point-to-Point Protocol) Support [Y] PPP Deflate Compression [Y] USB Support Support for USB [Y] Preliminary USB Device Filesystem [Y] UHCI (Intel PIIX4, VIA,...) Support [M] OHCI (Compaq, iMacs, OPTi, SiS, ALi, ...) support [M] For PPPoA you will need the following options: Network Device Support PPP Over ATM (EXPERIMENTAL) [Y] Then I recompiled the kernel and booted into it. I think that's what I did, but its confusing as a nebie :o) I then get the following errors when I try a make in the speedbundle-1.0 directory: [EMAIL PROTECTED] speedbundle-1.0]$ ls configure firmware_loader linux-atm ppp_scripts configure-stamp hotplug_scripts Makefile README firmware kernel_module ppp [EMAIL PROTECTED] speedbundle-1.0]$ make cd kernel_module && make make[1]: Entering directory `/home/tim/dsl/speedbundle-1.0/kernel_module' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/home/tim/dsl/speedbundle-1.0/kernel_module' cd linux-atm && make make[1]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm' make all-recursive make[2]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm' Making all in m4 make[3]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/m4' make[3]: Nothing to be done for `all'. make[3]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/m4' Making all in src make[3]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src' Making all in include make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/include' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/include'Making all in lib make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/lib' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/lib' Making all in test make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/test' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/test' Making all in debug make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/debug' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/debug' Making all in qgen make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/qgen' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/qgen' Making all in saal make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/saal' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/saal' Making all in sigd make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/sigd' make[4]: Nothing to be done for `all'. make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/sigd' Making all in maint make[4]: Entering directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/maint' gcc -DHAVE_CONFIG_H -I. -I. -I../.. -I../../src/qgen -I../../src/saal -I. -I ../../src/include -g -O2 -Wall -Wshadow -Wpointer-arith -Wwrite-strings -Wst rict-prototypes -c sonetdiag.c In file included from /usr/include/linux/sonet.h:61, from sonetdiag.c:18: /usr/include/asm/atomic.h:40:2: warning: #warning Using kernel header in userland program. BAD! In file included from sonetdiag.c:18: /usr/include/linux/sonet.h:65: error: syntax error before "__SONET_ITEMS" make[4]: *** [sonetdiag.o] Error 1 make[4]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src/maint' make[3]: *** [all-recursive] Error 1 make[3]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm/src' make[2]: *** [all-recursive] Error 1 make[2]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm' make[1]: *** [all-recursive-am] Error 2 make[1]: Leaving directory `/home/tim/dsl/speedbundle-1.0/linux-atm' make: *** [build-stamp] Error 2 [EMAIL PROTECTED] speedbundle-1.0]$ I've searched around on various sites and in the archive but am now stuck. Any help greatly appreciated. Regards, Tim The Newbie *********************************************************************** This email and any files attached to it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. The message and any files attached to it have been scanned by MIMEsweeper with Sophos Sweep and found to be free from all known viruses. Information on MIMEsweeper can be found at http://www.mimesweeper.com/ *********************************************************************** Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
