On Sun, 2004-05-16 at 22:06, Duncan Sands wrote:
> > I have also noticed the problems with FC2 test3, and am willing to try
> > to make the changes in the final version of FC2 which will be released
> > next week. Could you then please send me the required file(s) that I
> > need to check and update? And maybe some pointers where in the source
> > files I need to look...
> >
> > When I get it to work I can post a patch file, so that every FC2 user
> > can enjoy his Speedtouch again.
>
> These should do the trick:
>
> http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED]
> http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED]
> http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED]
> http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED]
> http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED]
> http://linux.bkbits.net:8080/linux-2.5/[EMAIL PROTECTED]|[EMAIL PROTECTED]
>
> Ciao,
>
> Duncan.
Hi Duncan,
after applying the patches and running part of speedbundle-1.0, it still
does not work :-(
I have attached the details of my modifications and results:
Steps taken to get the Speedtouch 330 to work:
- apply the patches you mentioned to the Fedora Core 2 kernel
- cd /usr/src/linux-2.6.5-1.358
- gedit include/linux/usbdevice_fs.h&
- gedit drivers/usb/core/inode.c&
- gedit drivers/usb/core/devio.c&
- reconfigure kernel:
- cp configs/kernel-2.6.5-i686.config .config
- make oldconfig
- make gconfig
- Device drivers->Networking Support->Networking options
->Asynchronous Transfer Mode (ATM) : build as module
- Then also select RFC1483/2684 Bridged Protocols: build as module
and switch off "Per VC IP filter kludge"
- Device Drivers->Networking Support->Network Device Support->PPP
Support->PPP over ATM: build as module
- Device Drivers->USB Support->Alcatel Speedtouch USB Support:
build as module
- save all modifications
- make
- make modules_install install
- add new kernel to grub.conf
- run (part) of speedbundle-1.0
(see also http://www.4p8.com/eric.brasseur/speedbundle_fedora.html):
- I don't have a (ethernet) network interface in my computer (no
default route/gateway)
- Unpack speedbundle
- cd speedbundle-1.0
- Do not exchange sonet.h by another one
- Put firmware at right place
- copy ppp_scripts/speedtch-pppoatm to ppp_scripts/speedtch and edit
username and vpi.vci
- edit chap-secrets and pap-secrets to include my isp-log-in
information
- edit Makefile and configure script, to comment out kernel_module,
linux-atm and ppp
- I did not remove the ppp package
- make
- make install
- reboot to see if everything works correctly
- during boot I see the leds flash and in the end both leds are green
- then I look into /var/log/messages:
<snip>
May 23 08:07:28 localhost kernel: USB Universal Host Controller
Interface driver v2.2
May 23 08:07:28 localhost kernel: uhci_hcd 0000:00:04.2: UHCI Host
Controller
May 23 08:07:28 localhost kernel: uhci_hcd 0000:00:04.2: irq 9,
io base 0000d400
May 23 08:07:28 localhost kernel: uhci_hcd 0000:00:04.2: new USB
bus registered, assigned bus number 1
May 23 08:07:28 localhost kernel: hub 1-0:1.0: USB hub found
May 23 08:07:28 localhost kernel: hub 1-0:1.0: 2 ports detected
May 23 08:07:28 localhost kernel: uhci_hcd 0000:00:04.3: UHCI Host
Controller
May 23 08:07:28 localhost kernel: uhci_hcd 0000:00:04.3: irq 9,
io base 0000d000
May 23 08:07:28 localhost kernel: uhci_hcd 0000:00:04.3: new USB
bus registered, assigned bus number 2
May 23 08:07:28 localhost kernel: hub 2-0:1.0: USB hub found
May 23 08:07:29 localhost kernel: hub 2-0:1.0: 2 ports detected
May 23 08:07:29 localhost kernel: usb 1-2: new full speed USB
device using address 2
May 23 08:07:29 localhost kernel: hub 1-2:1.0: USB hub found
May 23 08:07:29 localhost kernel: device-mapper: 4.1.0-ioctl
(2003-12-10) initial
ised: [EMAIL PROTECTED]
May 23 08:07:29 localhost kernel: usb 1-2: control timeout on ep0in
May 23 08:07:29 localhost kernel: hub 1-2:1.0: config failed, can't
read hub descriptor (err -110)
May 23 08:07:29 localhost kernel: usb 2-2: new full speed USB
device using address 2
May 23 08:07:29 localhost kernel: hub 2-2:1.0: USB hub found
May 23 08:07:29 localhost kernel: hub 2-2:1.0: 4 ports detected
May 23 08:07:29 localhost kernel: usb 2-2.2: new full speed USB
device using address 3
May 23 08:07:29 localhost kernel: usbcore: registered new driver
speedtch
May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 1
claimed while 'modem_run' sets config #1
May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 2
claimed while 'modem_run' sets config #1
May 23 08:07:29 localhost kernel: usb 2-2.2: bulk timeout on ep5in
May 23 08:07:29 localhost kernel: usbfs: USBDEVFS_BULK failed
dev 3 ep 0x85 len 512 ret -110
May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 0
claimed while 'modem_run' sets config #1
May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 1
claimed while 'modem_run' sets config #1
May 23 08:07:29 localhost kernel: usb 2-2.2: usbfs: interface 2
claimed while 'modem_run' sets config #1
May 23 08:07:47 localhost kernel: usbfs: process 1608 (modem_run)
did not claim interface 0 before use
May 23 08:07:52 localhost pppd[2658]:/usr/lib/./pppd/2.4.2/
pppoatm.so: cannot open shared object file: No such file or
directory
May 23 08:07:52 localhost pppd[2658]: Couldn't load plugin
pppoatm.so
</snip>
- from this I see two (different) problems:
1) the firmware downloading modem goes wrong
2) pppoatm.so is missing
Do you have any suggestions for next steps that I can take?
Regards,
Aad
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]
