Hardware is SUNW,Ultra-250 & OS is version 5.8.
Berkeley DB version 2.7.7 downloaded OK and "gzip", "./configure",
"make", "make install" & "make clean" all work fine.
squidGuard version 1.2.0 downloaded OK and "gzip" & "./configure" work
fine, but "make" produces the following output:-
making all in squidGuard-1.2.0
make[1]: Entering directory `/info/squidGuard-1.2.0/src'
making all in src
cc -I.. -I. -I. -I/usr/local/BerkeleyDB/include -DHAVE_CONFIG_H -g
-I/usr/local/
BerkeleyDB/include -c main.c
"main.c", line 78: syntax error before or at: char
"main.c", line 78: parameter not in identifier list: envp
"main.c", line 80: syntax error before or at: {
"main.c", line 81: parameter not in identifier list: ch
"main.c", line 82: parameter not in identifier list: squidInfo
"main.c", line 83: parameter not in identifier list: src
"main.c", line 84: parameter not in identifier list: acl
"main.c", line 85: parameter not in identifier list: start_time
"main.c", line 85: parameter not in identifier list: ready_time
"main.c", line 85: parameter not in identifier list: stop_time
"main.c", line 86: parameter not in identifier list: buf
"main.c", line 87: parameter not in identifier list: redirect
"main.c", line 87: parameter not in identifier list: tmp
"main.c", line 88: parameter not in identifier list: configFile
"main.c", line 88: cannot initialize parameter: configFile
"main.c", line 88: warning: statement not reached
"main.c", line 89: parameter not in identifier list: t
"main.c", line 91: parameter not in identifier list: act
"main.c", line 93: syntax error before or at: &
"main.c", line 93: parameter not in identifier list: gettimeofday
"main.c", line 94: parameter not in identifier list: progname
"main.c", line 94: cannot initialize parameter: progname
"main.c", line 94: non-constant initializer: op "U*"
"main.c", line 95: parameter not in identifier list: globalPid
"main.c", line 95: cannot initialize parameter: globalPid
"main.c", line 95: non-constant initializer: op "UCALL"
"main.c", line 96: syntax error before or at: while
"main.c", line 96: syntax error before or at: =
"main.c", line 96: syntax error before or at: "hduC:t:c:v"
"main.c", line 96: parameter not in identifier list: getopt
"main.c", line 97: parameter not in identifier list: ch
"main.c", line 97: identifier redeclared: ch
current : int
previous: int : "main.c", line 81
"main.c", line 98: "case" outside switch
"main.c", line 100: "break" outside loop or switch
"main.c", line 101: "case" outside switch
"main.c", line 102: warning: statement not reached
"main.c", line 103: "break" outside loop or switch
"main.c", line 104: "case" outside switch
"main.c", line 105: warning: statement not reached
"main.c", line 106: "break" outside loop or switch
"main.c", line 107: "case" outside switch
"main.c", line 108: warning: statement not reached
"main.c", line 109: "break" outside loop or switch
"main.c", line 110: "case" outside switch
"main.c", line 111: warning: statement not reached
"main.c", line 113: "break" outside loop or switch
"main.c", line 114: "case" outside switch
"main.c", line 115: warning: statement not reached
"main.c", line 126: "break" outside loop or switch
"main.c", line 127: "case" outside switch
"main.c", line 128: "case" outside switch
"main.c", line 129: "default" outside switch
"main.c", line 131: cannot recover from previous errors
cc: acomp failed for main.c
make[1]: *** [main.o] Error 2
make[1]: Leaving directory `/info/squidGuard-1.2.0/src'
make: *** [all] Error 1
Any ideas folks?
Bob Stevenson
ITaCS
University of Sunderland
begin:vcard
n:Stevenson;Bob
x-mozilla-html:FALSE
org:University of Sunderland;ITaCS
adr:;;;;;;
version:2.1
email;internet:[EMAIL PROTECTED]
title:Mr.
fn:Bob Stevenson
end:vcard
