Hey Fred, thanks for the info and the example on how to handle this. I'll take a look at it and try to get it working Thanks again
On Tue, Nov 28, 2023 at 11:45 PM Fred Posner <[email protected]> wrote: > Hi Saul, > > Great to see you here… > > So, there’s not a ton of examples out there on UAC, but many of us have > done what you’re describing and later on I’ll try to respond with a config > example. > > Nick vs Networking has some good, verbose discussions on many modules > including; > > https://nickvsnetworking.com/kamailio-bytes-sip-uac-module-to-act-as-a-uac-sip-client/ > > For what you’re talking about doing, I’d probably have the credentials > stored in a DB (mariadb, Postgres, etc) and then have that register to the > carriers. > > Asterisk would connect to your Kamailio, and then using whatever logic you > want (LCR, x-header, favorite, etc) you would then send out to the carrier > with kamailio handling (via uac) the authentication on the INVITEs. > > For incoming, it depends on the carrier how you receive the call. Some > carriers will send all dids to just your registered username, others will > send with DID info in the SIP. > > Every carrier is a snowflake. > > Keeping with the snowflake theme, some carriers are also “finicky” on > outbound traffic and don’t like to see certain SIP; where some modules like > topos may assist. > > > Regards, > > Fred Posner > p: +1 (352) 664-3733 > > > > > On Nov 28, 2023, at 8:26 PM, Saul Ibarra via sr-users < > [email protected]> wrote: > > > > Thanks for your response, > > I have checked the UAC module, but i would like get more information > about how it works. I have worked with Asterisk in the past, if i were to > handle this let's say with an asterisk in the middle, it will probably be > two sip accounts + a dialplan config to make them call each other > > > > So here the "equivalent" is UAC module to do the 'register' to the > provider, but, does it means that as soon as kamailio have the provider > credentials it will try to register? > > > > While using a DB (i'm using mariadb), will any update on the DB be > automatically accessible by Kamailio or i should do some 'reload' for it? > > > > I'm confused by the way it works which is pretty different from Asterisk > in the end, but i like the idea of having also full control over what's > happening and when > > > > > > On Tue, Nov 28, 2023 at 9:39 PM Yuriy G <[email protected]> wrote: > > Hi. Use UAC module > > Examples of the configuration are in the docs > > > > https://www.kamailio.org/docs/modules/5.7.x/modules/uac.html#idm700 > > > > On Wed, Nov 29, 2023, 01:26 Saul Ibarra via sr-users < > [email protected]> wrote: > > Hi, > > I am needing some help setting up kamailio as a sip proxy between a > provider(trunk) and a test pbx > > The trunk requires username&password and i would like to add that > information to the request within the Kamailio proxy, so that the PBX can > authenticate directly by IP (without username&password) through the > Kamailio proxy. > > > > As a programmer with a limited background in SIP (currently learning), I > am keen on understanding the intricacies of this setup at the SIP level. > > Could you please direct me to resources or documentation that covers > scenarios similar to mine? > > > > Any help or guidance you could provide would be greatly appreciated. > > > > Thanks > > __________________________________________________________ > > Kamailio - Users Mailing List - Non Commercial Discussions > > To unsubscribe send an email to [email protected] > > Important: keep the mailing list in the recipients, do not reply only to > the sender! > > Edit mailing list options or unsubscribe: > > __________________________________________________________ > > Kamailio - Users Mailing List - Non Commercial Discussions > > To unsubscribe send an email to [email protected] > > Important: keep the mailing list in the recipients, do not reply only to > the sender! > > Edit mailing list options or unsubscribe: > >
__________________________________________________________ Kamailio - Users Mailing List - Non Commercial Discussions To unsubscribe send an email to [email protected] Important: keep the mailing list in the recipients, do not reply only to the sender! Edit mailing list options or unsubscribe:
