StartFragmentHi, I'm new to Kamailio and I'm trying to setup a load balancer using Kamailio 4.0 and rtpproxy, to balance between 2 asterisk servers that provide an IVR service.
I've followed several guides, and so far it seems to work along with rtpproxy, except it is not sending the BYE message back to asterisk, and the call never finishes from the asterisk POV. Let me describe the test scenario: I have the following: IP phone: 192.168.200.183 PBX: 192.168.200.3 Kamailio: 192.168.200.132 IVR1: 192.168.200.160 IVR2: 192.168.200.161 >From the IP phone which is registered on the PBX, I initiate a call to exten 800, PBX forwards it to 1234@192.168.200.132:5060 and Kamailio dispatches it to one of the two IVR in round-robin. I'm testing this way and not calling directly to Kamailio because in the production enviroment, calls will be coming from outside. Attached you will find the Kamailio configuration. Packet capture made at the Kamailio host, where you can see the BYE package from the PBX (first one on line 24) but no BYE package sent to the IVRs is here: http://cringer.3kh.net/web/misc/sip.cap Please let me know if I ommited any important detail of my setup and thanks in advance. Best regards. -- Ariel Wainer
0 sip:192.168.200.160:5062 0 sip:192.168.200.161:5062
#!KAMAILIO # # Kamailio (OpenSER) SIP Server v4.0 - default configuration script # - web: http://www.kamailio.org # - git: http://sip-router.org # # Direct your questions about this file to: <sr-users@lists.sip-router.org> # # Refer to the Core CookBook at http://www.kamailio.org/wiki/ # for an explanation of possible statements, functions and parameters. # # Several features can be enabled using '#!define WITH_FEATURE' directives: # # *** To run in debug mode: # - define WITH_DEBUG # # *** To enable mysql: # - define WITH_MYSQL # # *** To enable authentication execute: # - enable mysql # - define WITH_AUTH #####!define WITH_AUTH # - add users using 'kamctl' # # *** To enable IP authentication execute: # - enable mysql # - enable authentication # - define WITH_IPAUTH # - add IP addresses with group id '1' to 'address' table # # *** To enable persistent user location execute: # - enable mysql # - define WITH_USRLOCDB # # *** To enable presence server execute: # - enable mysql # - define WITH_PRESENCE # # *** To enable nat traversal execute: # - define WITH_NAT # - install RTPProxy: http://www.rtpproxy.org # - start RTPProxy: # rtpproxy -l _your_public_ip_ -s udp:localhost:7722 # # *** To enable PSTN gateway routing execute: # - define WITH_PSTN # - set the value of pstn.gw_ip # - check route[PSTN] for regexp routing condition # # *** To enable database aliases lookup execute: # - enable mysql # - define WITH_ALIASDB # # *** To enable speed dial lookup execute: # - enable mysql # - define WITH_SPEEDDIAL # # *** To enable multi-domain support execute: # - enable mysql # - define WITH_MULTIDOMAIN # # *** To enable TLS support execute: # - adjust CFGDIR/tls.cfg as needed # - define WITH_TLS # # *** To enable XMLRPC support execute: # - define WITH_XMLRPC # - adjust route[XMLRPC] for access policy # # *** To enable anti-flood detection execute: # - adjust pike and htable=>ipban settings as needed (default is # block if more than 16 requests in 2 seconds and ban for 300 seconds) # - define WITH_ANTIFLOOD # # *** To block 3XX redirect replies execute: # - define WITH_BLOCK3XX # # *** To enable VoiceMail routing execute: # - define WITH_VOICEMAIL # - set the value of voicemail.srv_ip # - adjust the value of voicemail.srv_port # # *** To enhance accounting execute: # - enable mysql # - define WITH_ACCDB # - add following columns to database #!define WITH_LOADBALANCE #!ifdef ACCDB_COMMENT ALTER TABLE acc ADD COLUMN src_user VARCHAR(64) NOT NULL DEFAULT ''; ALTER TABLE acc ADD COLUMN src_domain VARCHAR(128) NOT NULL DEFAULT ''; ALTER TABLE acc ADD COLUMN src_ip varchar(64) NOT NULL default ''; ALTER TABLE acc ADD COLUMN dst_ouser VARCHAR(64) NOT NULL DEFAULT ''; ALTER TABLE acc ADD COLUMN dst_user VARCHAR(64) NOT NULL DEFAULT ''; ALTER TABLE acc ADD COLUMN dst_domain VARCHAR(128) NOT NULL DEFAULT ''; ALTER TABLE missed_calls ADD COLUMN src_user VARCHAR(64) NOT NULL DEFAULT ''; ALTER TABLE missed_calls ADD COLUMN src_domain VARCHAR(128) NOT NULL DEFAULT ''; ALTER TABLE missed_calls ADD COLUMN src_ip varchar(64) NOT NULL default ''; ALTER TABLE missed_calls ADD COLUMN dst_ouser VARCHAR(64) NOT NULL DEFAULT ''; ALTER TABLE missed_calls ADD COLUMN dst_user VARCHAR(64) NOT NULL DEFAULT ''; ALTER TABLE missed_calls ADD COLUMN dst_domain VARCHAR(128) NOT NULL DEFAULT ''; #!endif ####### Include Local Config If Exists ######### import_file "kamailio-local.cfg" ####### Defined Values ######### # *** Value defines - IDs used later in config #!ifdef WITH_MYSQL # - database URL - used to connect to database server by modules such # as: auth_db, acc, usrloc, a.s.o. #!ifndef DBURL #!define DBURL "mysql://kamailio:kamailiorw@localhost/kamailio" #!endif #!endif #!ifdef WITH_MULTIDOMAIN # - the value for 'use_domain' parameters #!define MULTIDOMAIN 1 #!else #!define MULTIDOMAIN 0 #!endif # - flags # FLT_ - per transaction (message) flags # FLB_ - per branch flags #!define FLT_ACC 1 #!define FLT_ACCMISSED 2 #!define FLT_ACCFAILED 3 #!define FLT_NATS 5 #!define FLB_NATB 6 #!define FLB_NATSIPPING 7 ####### Global Parameters ######### ### LOG Levels: 3=DBG, 2=INFO, 1=NOTICE, 0=WARN, -1=ERR #!ifdef WITH_DEBUG debug=4 log_stderror=yes #!else debug=2 log_stderror=no #!endif memdbg=5 memlog=5 log_facility=LOG_LOCAL0 fork=yes children=4 /* uncomment the next line to disable TCP (default on) */ #disable_tcp=yes /* uncomment the next line to disable the auto discovery of local aliases based on reverse DNS on IPs (default on) */ #auto_aliases=no /* add local domain aliases */ #alias="sip.mydomain.com" /* uncomment and configure the following line if you want Kamailio to bind on a specific interface/port/proto (default bind on all available) */ #listen=udp:10.0.0.10:5060 /* port to listen to * - can be specified more than once if needed to listen on many ports */ port=5060 #!ifdef WITH_TLS enable_tls=yes #!endif # life time of TCP connection when there is no traffic # - a bit higher than registration expires to cope with UA behind NAT tcp_connection_lifetime=3605 ####### Custom Parameters ######### # These parameters can be modified runtime via RPC interface # - see the documentation of 'cfg_rpc' module. # # Format: group.id = value 'desc' description # Access: $sel(cfg_get.group.id) or @cfg_get.group.id # #!ifdef WITH_PSTN # PSTN GW Routing # # - pstn.gw_ip: valid IP or hostname as string value, example: # pstn.gw_ip = "10.0.0.101" desc "My PSTN GW Address" # # - by default is empty to avoid misrouting pstn.gw_ip = "" desc "PSTN GW Address" pstn.gw_port = "" desc "PSTN GW Port" #!endif #!ifdef WITH_VOICEMAIL # VoiceMail Routing on offline, busy or no answer # # - by default Voicemail server IP is empty to avoid misrouting voicemail.srv_ip = "" desc "VoiceMail IP Address" voicemail.srv_port = "5060" desc "VoiceMail Port" #!endif ####### Modules Section ######## # set paths to location of modules (to sources or installation folders) #!ifdef WITH_SRCPATH mpath="modules_k:modules" #!else mpath="/usr/local/lib/kamailio/modules_k/:/usr/lib64/kamailio/modules/" #!endif #!ifdef WITH_MYSQL loadmodule "db_mysql.so" #!endif loadmodule "mi_fifo.so" loadmodule "kex.so" loadmodule "corex.so" loadmodule "tm.so" loadmodule "tmx.so" loadmodule "sl.so" loadmodule "rr.so" loadmodule "pv.so" loadmodule "maxfwd.so" loadmodule "usrloc.so" loadmodule "registrar.so" loadmodule "textops.so" loadmodule "siputils.so" loadmodule "xlog.so" loadmodule "sanity.so" loadmodule "ctl.so" loadmodule "cfg_rpc.so" loadmodule "mi_rpc.so" loadmodule "acc.so" loadmodule "path.so" #!ifdef WITH_AUTH loadmodule "auth.so" loadmodule "auth_db.so" #!ifdef WITH_IPAUTH loadmodule "permissions.so" #!endif #!endif #!ifdef WITH_ALIASDB loadmodule "alias_db.so" #!endif #!ifdef WITH_SPEEDDIAL loadmodule "speeddial.so" #!endif #!ifdef WITH_MULTIDOMAIN loadmodule "domain.so" #!endif #!ifdef WITH_PRESENCE loadmodule "presence.so" loadmodule "presence_xml.so" #!endif #!ifdef WITH_NAT loadmodule "nathelper.so" loadmodule "rtpproxy.so" #!endif #!ifdef WITH_TLS loadmodule "tls.so" #!endif #!ifdef WITH_ANTIFLOOD loadmodule "htable.so" loadmodule "pike.so" #!endif #!ifdef WITH_XMLRPC loadmodule "xmlrpc.so" #!endif #!ifdef WITH_DEBUG loadmodule "debugger.so" #!endif #!ifdef WITH_LOADBALANCE loadmodule "dispatcher.so" #!endif # ----------------- setting module-specific parameters --------------- # ----- mi_fifo params ----- modparam("mi_fifo", "fifo_name", "/tmp/kamailio_fifo") # ----- tm params ----- # auto-discard branches from previous serial forking leg modparam("tm", "failure_reply_mode", 3) # default retransmission timeout: 30sec modparam("tm", "fr_timer", 30000) # default invite retransmission timeout after 1xx: 120sec modparam("tm", "fr_inv_timer", 120000) # ----- rr params ----- # add value to ;lr param to cope with most of the UAs modparam("rr", "enable_full_lr", 1) # do not append from tag to the RR (no need for this script) modparam("rr", "append_fromtag", 0) # ----- registrar params ----- modparam("registrar", "method_filtering", 1) /* uncomment the next line to disable parallel forking via location */ # modparam("registrar", "append_branches", 0) /* uncomment the next line not to allow more than 10 contacts per AOR */ #modparam("registrar", "max_contacts", 10) # max value for expires of registrations modparam("registrar", "max_expires", 3600) # set it to 1 to enable GRUU modparam("registrar", "gruu_enabled", 0) # ----- acc params ----- /* what special events should be accounted ? */ modparam("acc", "early_media", 0) modparam("acc", "report_ack", 0) modparam("acc", "report_cancels", 0) /* by default ww do not adjust the direct of the sequential requests. if you enable this parameter, be sure the enable "append_fromtag" in "rr" module */ modparam("acc", "detect_direction", 0) /* account triggers (flags) */ modparam("acc", "log_flag", FLT_ACC) modparam("acc", "log_missed_flag", FLT_ACCMISSED) modparam("acc", "log_extra", "src_user=$fU;src_domain=$fd;src_ip=$si;" "dst_ouser=$tU;dst_user=$rU;dst_domain=$rd") modparam("acc", "failed_transaction_flag", FLT_ACCFAILED) /* enhanced DB accounting */ #!ifdef WITH_ACCDB modparam("acc", "db_flag", FLT_ACC) modparam("acc", "db_missed_flag", FLT_ACCMISSED) modparam("acc", "db_url", DBURL) modparam("acc", "db_extra", "src_user=$fU;src_domain=$fd;src_ip=$si;" "dst_ouser=$tU;dst_user=$rU;dst_domain=$rd") #!endif # ----- usrloc params ----- /* enable DB persistency for location entries */ #!ifdef WITH_USRLOCDB modparam("usrloc", "db_url", DBURL) modparam("usrloc", "db_mode", 2) modparam("usrloc", "use_domain", MULTIDOMAIN) #!endif # ----- auth_db params ----- #!ifdef WITH_AUTH modparam("auth_db", "db_url", DBURL) modparam("auth_db", "calculate_ha1", yes) modparam("auth_db", "password_column", "password") modparam("auth_db", "load_credentials", "") modparam("auth_db", "use_domain", MULTIDOMAIN) # ----- permissions params ----- #!ifdef WITH_IPAUTH modparam("permissions", "db_url", DBURL) modparam("permissions", "db_mode", 1) #!endif #!endif # ----- alias_db params ----- #!ifdef WITH_ALIASDB modparam("alias_db", "db_url", DBURL) modparam("alias_db", "use_domain", MULTIDOMAIN) #!endif # ----- speeddial params ----- #!ifdef WITH_SPEEDDIAL modparam("speeddial", "db_url", DBURL) modparam("speeddial", "use_domain", MULTIDOMAIN) #!endif # ----- domain params ----- #!ifdef WITH_MULTIDOMAIN modparam("domain", "db_url", DBURL) # register callback to match myself condition with domains list modparam("domain", "register_myself", 1) #!endif #!ifdef WITH_PRESENCE # ----- presence params ----- modparam("presence", "db_url", DBURL) # ----- presence_xml params ----- modparam("presence_xml", "db_url", DBURL) modparam("presence_xml", "force_active", 1) #!endif #!ifdef WITH_NAT # ----- rtpproxy params ----- modparam("rtpproxy", "rtpproxy_sock", "udp:127.0.0.1:7722") # ----- nathelper params ----- modparam("nathelper", "natping_interval", 30) modparam("nathelper", "ping_nated_only", 1) modparam("nathelper", "sipping_bflag", FLB_NATSIPPING) modparam("nathelper", "sipping_from", "sip:pin...@kamailio.org") # params needed for NAT traversal in other modules modparam("nathelper|registrar", "received_avp", "$avp(RECEIVED)") modparam("usrloc", "nat_bflag", FLB_NATB) #!endif #!ifdef WITH_TLS # ----- tls params ----- modparam("tls", "config", "/etc/kamailio/tls.cfg") #!endif #!ifdef WITH_ANTIFLOOD # ----- pike params ----- modparam("pike", "sampling_time_unit", 2) modparam("pike", "reqs_density_per_unit", 16) modparam("pike", "remove_latency", 4) # ----- htable params ----- # ip ban htable with autoexpire after 5 minutes modparam("htable", "htable", "ipban=>size=8;autoexpire=300;") #!endif #!ifdef WITH_XMLRPC # ----- xmlrpc params ----- modparam("xmlrpc", "route", "XMLRPC"); modparam("xmlrpc", "url_match", "^/RPC") #!endif #!ifdef WITH_DEBUG # ----- debugger params ----- modparam("debugger", "cfgtrace", 1) #!endif ####### Routing Logic ######## #!ifdef WITH_LOADBALANCE modparam("dispatcher", "list_file", "/etc/kamailio/dispatcher.list") modparam("dispatcher", "flags", 2) modparam("dispatcher", "dst_avp", "$avp(AVP_DST)") modparam("dispatcher", "grp_avp", "$avp(AVP_GRP)") modparam("dispatcher", "cnt_avp", "$avp(AVP_CNT)") modparam("dispatcher", "ds_ping_interval", 20) modparam("dispatcher", "ds_ping_from", "sip:kamail...@awesomedomain.com") #modparam("dispatcher", "ds_ping_method", "INFO") modparam("dispatcher", "ds_probing_mode", 1) modparam("dispatcher", "ds_probing_threshhold", 1) #configure codes or classes of SIP replies to list only allowed replies (i.e. when temporarily unavailable=480) modparam("dispatcher", "ds_ping_reply_codes", "class=2;code=480;code=404") #!endif # Main SIP request routing logic # - processing of any incoming SIP request starts with this route # - note: this is the same as route { ... } request_route { #!ifdef WITH_LOADBALANCE #you can customize the condition however you need. For example, request uri checking, specific header checking, etc. if (is_method("INVITE")) route(LOADBALANCE); #{ # #we go to the load balancer route # route(LOADBALANCE); #} #else #{ # #we perform normal usrloc lookup for the call # route(LOCATION); #} ##!else ## user location service # route(LOCATION); #!endif } route[RELAY] { # enable additional event routes for forwarded requests # - serial forking, RTP relaying handling, a.s.o. if (is_method("INVITE|BYE|SUBSCRIBE|UPDATE")) { if(!t_is_set("branch_route")) t_on_branch("MANAGE_BRANCH"); } if (is_method("INVITE|SUBSCRIBE|UPDATE")) { if(!t_is_set("onreply_route")) t_on_reply("MANAGE_REPLY"); } if (is_method("INVITE")) { if(!t_is_set("failure_route")) t_on_failure("MANAGE_FAILURE"); } if (!t_relay()) { sl_reply_error(); } exit; } # Per SIP request initial checks route[REQINIT] { #!ifdef WITH_ANTIFLOOD # flood dection from same IP and traffic ban for a while # be sure you exclude checking trusted peers, such as pstn gateways # - local host excluded (e.g., loop to self) if(src_ip!=myself) { if($sht(ipban=>$si)!=$null) { # ip is already blocked xdbg("request from blocked IP - $rm from $fu (IP:$si:$sp)\n"); exit; } if (!pike_check_req()) { xlog("L_ALERT","ALERT: pike blocking $rm from $fu (IP:$si:$sp)\n"); $sht(ipban=>$si) = 1; exit; } } #!endif if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); exit; } if(!sanity_check("1511", "7")) { xlog("Malformed SIP message from $si:$sp\n"); exit; } } # Handle requests within SIP dialogs route[WITHINDLG] { if (has_totag()) { # sequential request withing a dialog should # take the path determined by record-routing if (loose_route()) { route(DLGURI); if (is_method("BYE")) { setflag(FLT_ACC); # do accounting ... setflag(FLT_ACCFAILED); # ... even if the transaction fails } else if ( is_method("ACK") ) { # ACK is forwarded statelessy route(NATMANAGE); } else if ( is_method("NOTIFY") ) { # Add Record-Route for in-dialog NOTIFY as per RFC 6665. record_route(); } route(RELAY); } else { if (is_method("SUBSCRIBE") && uri == myself) { # in-dialog subscribe requests route(PRESENCE); exit; } if ( is_method("ACK") ) { if ( t_check_trans() ) { # no loose-route, but stateful ACK; # must be an ACK after a 487 # or e.g. 404 from upstream server route(RELAY); exit; } else { # ACK without matching transaction ... ignore and discard exit; } } sl_send_reply("404","Not here"); } exit; } } # Handle SIP registrations route[REGISTRAR] { if (is_method("REGISTER")) { if(isflagset(FLT_NATS)) { setbflag(FLB_NATB); # uncomment next line to do SIP NAT pinging ## setbflag(FLB_NATSIPPING); } if (!save("location")) sl_reply_error(); exit; } } # USER location service route[LOCATION] { #!ifdef WITH_SPEEDDIAL # search for short dialing - 2-digit extension if($rU=~"^[0-9][0-9]$") if(sd_lookup("speed_dial")) route(SIPOUT); #!endif #!ifdef WITH_ALIASDB # search in DB-based aliases if(alias_db_lookup("dbaliases")) route(SIPOUT); #!endif $avp(oexten) = $rU; if (!lookup("location")) { $var(rc) = $rc; route(TOVOICEMAIL); t_newtran(); switch ($var(rc)) { case -1: case -3: send_reply("404", "Not Found"); exit; case -2: send_reply("405", "Method Not Allowed"); exit; } } # when routing via usrloc, log the missed calls also if (is_method("INVITE")) { setflag(FLT_ACCMISSED); } route(RELAY); exit; } # Presence server route route[PRESENCE] { if(!is_method("PUBLISH|SUBSCRIBE")) return; #!ifdef WITH_PRESENCE if (!t_newtran()) { sl_reply_error(); exit; }; if(is_method("PUBLISH")) { handle_publish(); t_release(); } else if( is_method("SUBSCRIBE")) { handle_subscribe(); t_release(); } exit; #!endif # if presence enabled, this part will not be executed if (is_method("PUBLISH") || $rU==$null) { sl_send_reply("404", "Not here"); exit; } return; } # Authentication route route[AUTH] { #!ifdef WITH_AUTH #!ifdef WITH_IPAUTH if((!is_method("REGISTER")) && allow_source_address()) { # source IP allowed return; } #!endif if (is_method("REGISTER") || from_uri==myself) { # authenticate requests if (!auth_check("$fd", "subscriber", "1")) { auth_challenge("$fd", "0"); exit; } # user authenticated - remove auth header if(!is_method("REGISTER|PUBLISH")) consume_credentials(); } # if caller is not local subscriber, then check if it calls # a local destination, otherwise deny, not an open relay here if (from_uri!=myself && uri!=myself) { sl_send_reply("403","Not relaying"); exit; } #!endif return; } # Caller NAT detection route route[NATDETECT] { #!ifdef WITH_NAT force_rport(); if (nat_uac_test("19")) { if (is_method("REGISTER")) { fix_nated_register(); } else { add_contact_alias(); } setflag(FLT_NATS); } #!endif return; } # RTPProxy control route[NATMANAGE] { #!ifdef WITH_NAT if (is_request()) { if(has_totag()) { if(check_route_param("nat=yes")) { setbflag(FLB_NATB); } } } if (!(isflagset(FLT_NATS) || isbflagset(FLB_NATB))) return; rtpproxy_manage(); if (is_request()) { if (!has_totag()) { add_rr_param(";nat=yes"); } } if (is_reply()) { if(isbflagset(FLB_NATB)) { add_contact_alias(); } } #!endif return; } # URI update for dialog requests route[DLGURI] { #!ifdef WITH_NAT if(!isdsturiset()) { handle_ruri_alias(); } #!endif return; } # Routing to foreign domains route[SIPOUT] { if (!uri==myself) { append_hf("P-hint: outbound\r\n"); route(RELAY); } } # PSTN GW routing route[PSTN] { #!ifdef WITH_PSTN # check if PSTN GW IP is defined if (strempty($sel(cfg_get.pstn.gw_ip))) { xlog("SCRIPT: PSTN rotuing enabled but pstn.gw_ip not defined\n"); return; } # route to PSTN dialed numbers starting with '+' or '00' # (international format) # - update the condition to match your dialing rules for PSTN routing if(!($rU=~"^(\+|00)[1-9][0-9]{3,20}$")) return; # only local users allowed to call if(from_uri!=myself) { sl_send_reply("403", "Not Allowed"); exit; } if (strempty($sel(cfg_get.pstn.gw_port))) { $ru = "sip:" + $rU + "@" + $sel(cfg_get.pstn.gw_ip); } else { $ru = "sip:" + $rU + "@" + $sel(cfg_get.pstn.gw_ip) + ":" + $sel(cfg_get.pstn.gw_port); } route(RELAY); exit; #!endif return; } # XMLRPC routing #!ifdef WITH_XMLRPC route[XMLRPC] { # allow XMLRPC from localhost if ((method=="POST" || method=="GET") && (src_ip==127.0.0.1)) { # close connection only for xmlrpclib user agents (there is a bug in # xmlrpclib: it waits for EOF before interpreting the response). if ($hdr(User-Agent) =~ "xmlrpclib") set_reply_close(); set_reply_no_connect(); dispatch_rpc(); exit; } send_reply("403", "Forbidden"); exit; } #!endif # route to voicemail server route[TOVOICEMAIL] { #!ifdef WITH_VOICEMAIL if(!is_method("INVITE")) return; # check if VoiceMail server IP is defined if (strempty($sel(cfg_get.voicemail.srv_ip))) { xlog("SCRIPT: VoiceMail rotuing enabled but IP not defined\n"); return; } if($avp(oexten)==$null) return; $ru = "sip:" + $avp(oexten) + "@" + $sel(cfg_get.voicemail.srv_ip) + ":" + $sel(cfg_get.voicemail.srv_port); route(RELAY); exit; #!endif return; } #!ifdef WITH_LOADBALANCE route[LOADBALANCE] { #ds_select_dst(destination_set, algorithm) function chooses the destination for the call. For this it can use a lot of algorithms. #Alg. 0 is the default one that does the the choosing over the call ID hash #Alg. 4 is a Round-Robin #Alg. 10 is the one that chooses the destination based on the minimum load of all destinations if(!ds_select_dst("0", "4")) { #if we are here that means no destination is available. We notify the user by 404 and exit the script. xlog("L_INFO", "No destination available!"); send_reply("404", "No destination"); exit; } #ds_select_domain("0","4"); xlog("L_INFO", "Routing call to <$ru> via <$du>\n"); route(RELAY); #record_route(); #forward(); #exit(); #set the no_reply_recieved timeout to 2 second ... adjust the value to your need #note: The first value "0" is invite timeout .. we do not need to change it #This means that is the selected media server fails to respond within 2 seconds the failure_route "MANAGE_FAILURE" is called #note: this implies that ale the signaling from media servers on the way back to the user goes through the proxy as well #t_set_fr(0,2000); #t_on_failure("MANAGE_FAILURE"); #add_path_received(); #force_rport(); #forward(); #return; } #!endif # manage outgoing branches branch_route[MANAGE_BRANCH] { xdbg("new branch [$T_branch_idx] to $ru\n"); route(NATMANAGE); } # manage incoming replies onreply_route[MANAGE_REPLY] { xdbg("incoming reply\n"); if(status=~"[12][0-9][0-9]") route(NATMANAGE); } # manage failure routing cases failure_route[MANAGE_FAILURE] { route(NATMANAGE); if (t_is_canceled()) { exit; } #!ifdef WITH_LOADBALANCE xlog("L_INFO", "Media server $du failed to answer, selecting other one!"); # next DST - only for 500 reply or local timeout (set by t_set_fr()) if (t_check_status("500") || t_branch_timeout() || !t_branch_replied()) { #we mark the destination Inactive and Probing ds_mark_dst("ip"); #select the new destination if(ds_next_dst()) { #again set local timeout for reply t_set_fr(0,2000); t_on_failure("MANAGE_FAILURE"); route(RELAY); exit; } else { #last available node failed to reply, no other destinations available send_reply("404", "No destination"); exit; } } #!endif }
_______________________________________________ SIP Express Router (SER) and Kamailio (OpenSER) - sr-users mailing list sr-users@lists.sip-router.org http://lists.sip-router.org/cgi-bin/mailman/listinfo/sr-users
