This is a note to let you know that I've just added the patch titled
Revert "drivers/misc/ti-st: remove gpio handling"
to my char-misc git tree which can be found at
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git
in the char-misc-linus branch.
The patch will show up in the next release of the linux-next tree
(usually sometime within the next 24 hours during the week.)
The patch will hopefully also be merged in Linus's tree for the
next -rc kernel release.
If you have any questions about this process, please let me know.
>From a7e2ca17039edb5f782be519eaf9d8ea500ba7cc Mon Sep 17 00:00:00 2001
From: Luciano Coelho <[email protected]>
Date: Mon, 21 Jan 2013 13:12:42 +0200
Subject: Revert "drivers/misc/ti-st: remove gpio handling"
This reverts commit eccf2979b2c034b516e01b8a104c3739f7ef07d1.
The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.
Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.
Cc: stable <[email protected]> [3.7]
Acked-by: Tony Lindgren <[email protected]>
Signed-off-by: Luciano Coelho <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/misc/ti-st/st_kim.c | 37 ++++++++++++++++++++++++++++++++++++-
1 file changed, 36 insertions(+), 1 deletion(-)
diff --git a/drivers/misc/ti-st/st_kim.c b/drivers/misc/ti-st/st_kim.c
index 9ff942a..83269f1 100644
--- a/drivers/misc/ti-st/st_kim.c
+++ b/drivers/misc/ti-st/st_kim.c
@@ -468,6 +468,11 @@ long st_kim_start(void *kim_data)
if (pdata->chip_enable)
pdata->chip_enable(kim_gdata);
+ /* Configure BT nShutdown to HIGH state */
+ gpio_set_value(kim_gdata->nshutdown, GPIO_LOW);
+ mdelay(5); /* FIXME: a proper toggle */
+ gpio_set_value(kim_gdata->nshutdown, GPIO_HIGH);
+ mdelay(100);
/* re-initialize the completion */
INIT_COMPLETION(kim_gdata->ldisc_installed);
/* send notification to UIM */
@@ -509,7 +514,8 @@ long st_kim_start(void *kim_data)
* (b) upon failure to either install ldisc or download firmware.
* The function is responsible to (a) notify UIM about un-installation,
* (b) flush UART if the ldisc was installed.
- * (c) invoke platform's chip disabling routine.
+ * (c) reset BT_EN - pull down nshutdown at the end.
+ * (d) invoke platform's chip disabling routine.
*/
long st_kim_stop(void *kim_data)
{
@@ -541,6 +547,13 @@ long st_kim_stop(void *kim_data)
err = -ETIMEDOUT;
}
+ /* By default configure BT nShutdown to LOW state */
+ gpio_set_value(kim_gdata->nshutdown, GPIO_LOW);
+ mdelay(1);
+ gpio_set_value(kim_gdata->nshutdown, GPIO_HIGH);
+ mdelay(1);
+ gpio_set_value(kim_gdata->nshutdown, GPIO_LOW);
+
/* platform specific disable */
if (pdata->chip_disable)
pdata->chip_disable(kim_gdata);
@@ -733,6 +746,20 @@ static int kim_probe(struct platform_device *pdev)
/* refer to itself */
kim_gdata->core_data->kim_data = kim_gdata;
+ /* Claim the chip enable nShutdown gpio from the system */
+ kim_gdata->nshutdown = pdata->nshutdown_gpio;
+ err = gpio_request(kim_gdata->nshutdown, "kim");
+ if (unlikely(err)) {
+ pr_err(" gpio %ld request failed ", kim_gdata->nshutdown);
+ return err;
+ }
+
+ /* Configure nShutdown GPIO as output=0 */
+ err = gpio_direction_output(kim_gdata->nshutdown, 0);
+ if (unlikely(err)) {
+ pr_err(" unable to configure gpio %ld", kim_gdata->nshutdown);
+ return err;
+ }
/* get reference of pdev for request_firmware
*/
kim_gdata->kim_pdev = pdev;
@@ -779,10 +806,18 @@ err_core_init:
static int kim_remove(struct platform_device *pdev)
{
+ /* free the GPIOs requested */
+ struct ti_st_plat_data *pdata = pdev->dev.platform_data;
struct kim_data_s *kim_gdata;
kim_gdata = dev_get_drvdata(&pdev->dev);
+ /* Free the Bluetooth/FM/GPIO
+ * nShutdown gpio from the system
+ */
+ gpio_free(pdata->nshutdown_gpio);
+ pr_info("nshutdown GPIO Freed");
+
debugfs_remove_recursive(kim_debugfs_dir);
sysfs_remove_group(&pdev->dev.kobj, &uim_attr_grp);
pr_info("sysfs entries removed");
--
1.8.1.rc1.5.g7e0651a
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
