routeSampler only uses the routes that you already provide as input. Of course, you can use implausibleRoutes.py before running routeSampler to analyze and tailor the input.
Looking at your scenario, I see the following issues - uncoordinated/unjoined traffic light in the city center - missing acceleration lanes at your motorway on-ramps. This turns highway on-ramps into normal junctions and reduces flow significantly. (add ramps manually or rebuild your network with option --ramps.guess. This may split some edge which invalidates routes so afterwards you will have to regenerated your route files or repair them with duarouter option --repair regards, Jakob Am Mi., 8. Juli 2020 um 08:08 Uhr schrieb Anil Baral <baral.ani...@gmail.com >: > Thanks Barry. I tried to remove some routes that created traffic jams in > the network due to U-turn, but it only reduces some traffic jams. It > doesn't solve the jam in other parts of the network. I would like to know > if there is any other way to generate and check the implausible routes. Is > there a way to use implausibleRoute.py with routeSampler to improve the > traffic flow? > > > Thanks, > Anil > > On Mon, Jul 6, 2020 at 4:35 AM Evans, Barry <b.ev...@exeter.ac.uk> wrote: > >> Hi Anil, >> >> I haven't looked over the data but I had a similar problem when I was >> using routeSampler.py. One of causes I found for sever jams was to do with >> some vehicle routes either starting with or ending with a U-turn manoeuvre. >> >> What I did was run the model in the GUI and visually look for where these >> jams are occurring and then click on the car that I believe to be causing >> the jam to see if it is attempting a U-turn either at the start of its >> journey or the end. If it is I'd then go into the rou.xml file in a text >> editor like notepad++ and look at the id of the vehicle causing the jam and >> trim either the beginning or the end of its route accordingly to remove the >> U-turn manoeuvre. >> >> If this is the issue, removing these U-turns will help reduce jams. I >> hope this helps but if not maybe someone else who is more familiar with >> routeSampler.py could help. >> >> All the best, >> >> Barry >> >> >> -----Original Message----- >> From: sumo-user-boun...@eclipse.org [mailto:sumo-user-boun...@eclipse.org] >> On Behalf Of anilbaral >> Sent: 06 July 2020 19:23 >> To: sumo-user@eclipse.org >> Subject: [sumo-user] RouteSampler.py demand generation problems >> >> CAUTION: This email originated from outside of the organisation. Do not >> click links or open attachments unless you recognise the sender and know >> the content is safe. >> >> >> Hi all, >> I have use routeSampler.py to generate demand with edge count data. The >> edge data was generated from the flow file and contains the hourly count on >> the edges with detectors. I was successfully able to generate the vehicle >> using routeSampler, and the mismatch was almost negligible. However, when I >> run the simulation, I find a lot of jam during *peak hours*. I have used >> the actuated traffic light and most probably traffic light is not the cause >> of traffic jams. I am not sure how to deal with this problem. I think it >> is due to the routes that are being generated by routeSampler.py. Please >> suggest how can I deal with these issues and what can be the probable >> causes? >> >> Attached is the file: FILES_Sumo.rar >> < >> https://eur03.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsumo-user-mailing-list.90755.n8.nabble.com%2Ffile%2Ft411%2FFILES_Sumo.rar&data=02%7C01%7CB.Evans%40exeter.ac.uk%7C21cdeb20d03d445fb35b08d8217d9104%7C912a5d77fb984eeeaf321334d8f04a53%7C0%7C0%7C637296170474282354&sdata=Imeub1WorD8Cy04cUhEtgngsIbizggA6V8SApLjcIew%3D&reserved=0 >> > >> >> Thanks >> Anil >> >> >> >> >> -- >> Sent from: >> https://eur03.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsumo-user-mailing-list.90755.n8.nabble.com%2F&data=02%7C01%7CB.Evans%40exeter.ac.uk%7C21cdeb20d03d445fb35b08d8217d9104%7C912a5d77fb984eeeaf321334d8f04a53%7C0%7C0%7C637296170474282354&sdata=6rUASrTC93DTcLxEnU2x3WrQsK6%2FZYfvO%2BfJPzNXhLE%3D&reserved=0 >> _______________________________________________ >> sumo-user mailing list >> sumo-user@eclipse.org >> To unsubscribe from this list, visit >> https://eur03.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.eclipse.org%2Fmailman%2Flistinfo%2Fsumo-user&data=02%7C01%7CB.Evans%40exeter.ac.uk%7C21cdeb20d03d445fb35b08d8217d9104%7C912a5d77fb984eeeaf321334d8f04a53%7C0%7C0%7C637296170474282354&sdata=y5I1%2FYUxroZ2ar8JVjxG1B34WWC3WFBoGTqCuuzpFb0%3D&reserved=0 >> _______________________________________________ >> sumo-user mailing list >> sumo-user@eclipse.org >> To unsubscribe from this list, visit >> https://www.eclipse.org/mailman/listinfo/sumo-user >> > _______________________________________________ > sumo-user mailing list > sumo-user@eclipse.org > To unsubscribe from this list, visit > https://www.eclipse.org/mailman/listinfo/sumo-user >
_______________________________________________ sumo-user mailing list sumo-user@eclipse.org To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-user