Hi Oleg, Thank you for your reply.
I will wait with great anticipation for the new driver. :) On another note, would it be possible for me to run my own recorder application directly on the camera and access a jpeg stream and record to a hard drive? We would like to build a robotic device capable of recording the video stream and I was thinking that in stead of running the recording software on a seperate computer, I could run it on the camera since it's already running linux. Kind regards, *Richard Rigby* Software Developer www.redzone.com Ph: +64 9 479 9901 Fax: +64 9 479 9904 13 Tarndale Grove • Albany • Auckland 0632 • New Zealand On 26 February 2018 at 10:37, Oleg <support-list@support.elphel.com> wrote: > Hi, > > 14MPx is not yet supported in the current firmware but I'm working on the > driver at the moment - hopefully will have something within a couple weeks. > There's an old firmware where exposure, gains and lane phases can be set, > not much more. > > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 5555 x124 <+1%20801-783-5555> > Elphel, Inc. > > On Fri, Feb 23, 2018 at 11:23 AM, Andrey Filippov <and...@elphel.com> > wrote: > >> >> >> == == == == == == Forwarded message == == == == == == >> From : Richard Rigby<rri...@redzone.com> >> To : <support-l...@elphel.com> >> Date : Thu, 22 Feb 2018 18:28:08 -0800 >> Subject : 14Mpix sensor not detected >> == == == == == == Forwarded message == == == == == == >> >> Hello, >> >> I have a 393 board as well as one 5 Mpix sensor and one 14 Mpix sensor. >> However only the 5Mpix sensor is working. >> >> I am using the web interface to view the camera. >> >> I have tried to run the init_elphel393.py script for both sensors and it >> looks to me that the 14 Mpix sensor cannot be detected. >> >> This is the output from init_elphel393.py when only the 14 Mpix sensor >> is connected: >> [ 443.35] init_elphel393: Fan on >> [ 443.36] init_elphel393: Initialize USB hub >> [ 443.37] init_elphel393: 10389 was not detected: skipping USB hub init >> [ 443.37] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = >> 255.255.255.0 >> [ 443.38] init_elphel393: init_elphel393.py: imgsrv >> Set port number: 2323 >> Set port number: 2324 >> Set port number: 2325 >> Set port number: 2326 >> [ 443.77] init_elphel393: init_elphel393.py: auto exposure daemon >> autoexposure#0 started, daemon_bit=0x0, debug=0x1 >> autoexposure#1 started, daemon_bit=0x0, debug=0x1 >> autoexposure#2 started, daemon_bit=0x0, debug=0x1 >> autoexposure#3 started, daemon_bit=0x0, debug=0x1 >> [ 443.99] autocampars: Processing camera state: INITIALIZED >> [ 444.05] autocampars: Active sensor ports: master_port = -1 >> [ 444.07] autocampars: Sensors map read from the sysfs: [none, none, >> none, none],[none, none, none, none],[none, none, none, none],[none, none, >> none, none] >> [ 444.12] autocampars: get_application_mode()->4369 >> [ 444.17] autocampars: Detecting sensors for MT9P006 >> [ 444.20] autocampars: Got --init command for already initialized >> camera, trying to re-initialize >> [ 444.22] autocampars: after reset - current frame on master port = >> [ 444.25] autocampars: Reset camera state to BITSTREAM >> [ 444.33] autocampars: ports: >> [ 444.35] autocampars: *System FPGA version: 0x039300da* >> [ 444.38] autocampars: *Sensor interface type: PAR12* >> [ 444.45] autocampars: *Detected sensors: [none, none, none, >> none],[none, none, none, none],[none, none, none, none],[none, none, none, >> none]* >> [ 444.48] autocampars: Reached state: SENSORS_DETECTED >> [ 444.53] autocampars: Disabling sensor port 0 >> [ 444.56] autocampars: Disabling sensor port 1 >> [ 444.58] autocampars: Disabling sensor port 2 >> [ 444.61] autocampars: Disabling sensor port 3 >> [ 444.69] autocampars: Frames: -1, -1, -1, -1 >> [ 444.71] autocampars: Reached state: SENSORS_SYNCHRONIZED >> [ 444.74] autocampars: ports: >> [ 444.81] autocampars: init_cameras() start: >> camera_state=SENSORS_SYNCHRONIZED >> [ 444.86] autocampars: Collected gammas == Array >> ( >> ) >> >> [ 444.89] autocampars: will need to skip local frames >> [ 444.92] autocampars: Reached state PARAMETERS_PRESET >> [ 444.94] autocampars: Skipping frames >> [ 444.97] autocampars: Frame delay = 0 s >> [ 445.02] autocampars: Remaining trigger parameters: >> >> Warning: array_key_exists() expects parameter 2 to be array, null given >> in /usr/bin/autocampars.php on line 1074 >> >> Warning: array_key_exists() expects parameter 2 to be array, null given >> in /usr/bin/autocampars.php on line 1085 >> >> Warning: array_key_exists() expects parameter 2 to be array, null given >> in /usr/bin/autocampars.php on line 1086 >> >> Warning: array_key_exists() expects parameter 2 to be array, null given >> in /usr/bin/autocampars.php on line 1091 >> >> Warning: elphel_set_P_arr() expects parameter 2 to be array, null given >> in /usr/bin/autocampars.php on line 1095 >> [ 445.09] autocampars: Skipping more frames >> [ 445.14] autocampars: Reached state PARAMETERS_PRESET >> [ 445.17] autocampars: Reached state INITIALIZED >> [ 445.20] autocampars: Sensors on ports: were successfully initialized >> [ 445.22] autocampars: *INITIALIZED* >> [ 445.25] autocampars: *revisions differ* >> [ 445.27] autocampars: *Log file saved as /var/log/autocampars.log* >> [ 445.32] init_elphel393: init SATA >> [ 445.32] init_elphel393: 10389 was not detected: skipping SATA init >> [ 445.32] init_elphel393: Start GPS and event logger >> Initializing Exif template: /www/pages/exif.php init noGPS nocompass >> [ 445.75] init_elphel393: /var/volatile/state already exists >> [ 445.75] init_elphel393: *DONE, log file: /var/log/init_elphel393.log* >> >> >> This is the output from init_elphel393.py when only the 14 Mpix sensor >> is connected: >> [ 45.92] init_elphel393: Fan on >> [ 45.93] init_elphel393: Initialize USB hub >> [ 45.94] init_elphel393: 10389 was not detected: skipping USB hub init >> [ 45.94] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = >> 255.255.255.0 >> [ 45.95] init_elphel393: init_elphel393.py: imgsrv >> Set port number: 2323 >> Set port number: 2324 >> Set port number: 2325 >> Set port number: 2326 >> [ 46.34] init_elphel393: init_elphel393.py: auto exposure daemon >> autoexposure#0 started, daemon_bit=0x0, debug=0x1 >> autoexposure#1 started, daemon_bit=0x0, debug=0x1 >> autoexposure#2 started, daemon_bit=0x0, debug=0x1 >> autoexposure.c:141:main: autoexposure#2: drivers initialized >> autoexposure.c:146:main: autoexposure#2 started daemon_bit=0x0, debug=0x1 >> autoexposure.c:154:main: autoexposure#2 this_frame = 0xe2 >> autoexposure.c:157:main: frame 14: autoexposure#2 this_frame = 0xe2 >> autoexposure#3 started, daemon_bit=0x0, debug=0x1 >> [ 46.58] autocampars: Processing camera state: INITIALIZED >> [ 46.63] autocampars: Active sensor ports: 2 master_port = 2 >> [ 46.66] autocampars: Sensors map read from the sysfs: [none, none, >> none, none],[none, none, none, none],[mt9p006, none, none, none],[none, >> none, none, none] >> [ 46.71] autocampars: get_application_mode()->4369 >> [ 46.76] autocampars: Detecting sensors for MT9P006 >> [ 46.79] autocampars: Got --init command for already initialized >> camera, trying to re-initialize >> [ 46.81] autocampars: Current frame on master port =230, sleeping to >> give daemons a chance >> [ 51.84] autocampars: Current frame on master port =280, waking up, >> daemons should be dead already >> [ 51.87] autocampars: after reset - current frame on master port =281 >> [ 51.89] autocampars: Reset camera state to BITSTREAM >> [ 51.97] autocampars: ports:2 >> [ 52.02] autocampars: Started detection for sensor port 2 >> [ 52.05] autocampars: *System FPGA version: 0x039300da* >> [ 52.07] autocampars: *Sensor interface type: PAR12* >> [ 52.15] autocampars: *Detected sensors: [none, none, none, >> none],[none, none, none, none],[mt9p006, none, none, none],[none, none, >> none, none]* >> [ 52.17] autocampars: Reached state: SENSORS_DETECTED >> [ 52.43] autocampars: Disabling sensor port 0 >> [ 52.45] autocampars: Disabling sensor port 1 >> [ 52.48] autocampars: Disabling sensor port 3 >> [ 52.66] autocampars: Frames: -1, -1, 0, -1 >> [ 52.68] autocampars: Reached state: SENSORS_SYNCHRONIZED >> [ 52.71] autocampars: ports:2 >> [ 52.76] autocampars: autocampars.php parsed configuration file >> /etc/elphel393/autocampars2.xml. >> [ 52.84] autocampars: init_cameras() start: >> camera_state=SENSORS_SYNCHRONIZED >> [ 52.89] autocampars: Collected gammas == Array >> ( >> [2617] => 1 >> ) >> >> [ 52.95] autocampars: port 2 setting @1 init exposure: EXPOS= 1000 >> [ 53.05] autocampars: port 2 setting @8 restoring exposure: EXPOS= >> 10000 >> [ 53.08] autocampars: will need to skip local 7 frames >> [ 53.10] autocampars: Reached state PARAMETERS_PRESET >> [ 53.13] autocampars: Skipping 7 frames >> [ 53.15] autocampars: Frame delay = 0.1 s >> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 7 >> (0x7) are not available. this_frame=0x8, now=0x8 >> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to >> errors, skipping a frame >> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 8 >> (0x8) are not available. this_frame=0x9, now=0x9 >> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to >> errors, skipping a frame >> [ 54.62] autocampars: *Started camera in periodic self-triggered mode, >> period = 0.1 s* >> [ 54.65] autocampars: Reached state PARAMETERS_PRESET >> [ 54.68] autocampars: Reached state INITIALIZED >> [ 54.70] autocampars: Sensors on ports: 2 were successfully initialized >> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 9 >> (0x9) are not available. this_frame=0xa, now=0xa >> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to >> errors, skipping a frame >> [ 54.73] autocampars: *INITIALIZED* >> [ 54.75] autocampars: *Log file saved as /var/log/autocampars.log* >> [ 54.81] init_elphel393: init SATA >> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 10 >> (0xa) are not available. this_frame=0xb, now=0xb >> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to >> errors, skipping a frame >> [ 54.81] init_elphel393: 10389 was not detected: skipping SATA init >> [ 54.81] init_elphel393: Start GPS and event logger >> aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 11 >> (0xb) are not available. this_frame=0xc, now=0xc >> autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to >> errors, skipping a frame >> Initializing Exif template: /www/pages/exif.php init noGPS nocompass >> [ 55.24] init_elphel393: /var/volatile/state already exists >> [ 55.24] init_elphel393: *DONE, log file: /var/log/init_elphel393.log* >> >> Any assistance in resolving this would be greatly appreciated. >> >> >> Kind regards, >> >> *Richard Rigby* >> Software Developer >> >> >> www.redzone.com >> >> Ph: +64 9 479 9901 >> >> Fax: +64 9 479 9904 >> >> >> 13 Tarndale Grove • Albany • Auckland 0632 • New Zealand >> <https://maps.google.com/?q=13+Tarndale+Grove+%E2%80%A2+Albany+%E2%80%A2+Auckland+0632+%E2%80%A2+New+Zealand&entry=gmail&source=g> >> >> >> >> >> >> _______________________________________________ >> Support-list mailing list >> Support-list@support.elphel.com >> http://support.elphel.com/mailman/listinfo/support-list_supp >> ort.elphel.com >> >
_______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
