Hello Oleg! I got your mail and tested it yesterday.
It's working !!PERFECTLY!! Thank you very much! The next step which I will do is the geometric conversion to a panorama-frame on the pc. I will keep you informed. Thank you Oleg, Andreas Oleg Dzhimiev schrieb: > Hi Andreas, > > I'm not sure you got my last letter. Have you tried? Does it work? > > Oleg > > ---------- Forwarded message ---------- > From: *Oleg Dzhimiev* <[email protected] > <mailto:[email protected]>> > Date: 2009/12/8 > Subject: Re: [Elphel-support] combining frames > To: Andreas Bean <[email protected] <mailto:[email protected]>> > Cc: elphel support-list <[email protected] > <mailto:[email protected]>> > > > Hi Andreas, > > You were getting bad frames because in my scripts I supposed you set > the resolution like on the picture attached and you did it by scaling > - the camvc writes different values to sensors in these 2 cases and > I'm using these values to calculate the combined frame parts - my fault. > > So, could you set the resolution like shown on the picture and not in > tab 5? > I also put an input box for scaling to 10359_controls - 2 for 1/2, 3 > for 1/3 and so on. > Tested my script - it works for scale factor 2 (I need to test other > factors) and also for 1 at different resolutions. Sending you files > and x359.bit - the one you got from the CVS. > > The procedure: > 1. set phases > 2. set trigger > 3. set the correct result frame resoluton in camvc > 4. in 10359_controls - set scale factor to 2, check combined box if > it's not checked and start. > > Do you need binning/averaging also? > > Oleg > > 2009/12/8 Andreas Bean <[email protected] <mailto:[email protected]>> > > Hello Oleg, > > I just tested the new mode with the sources from cvs. I updated > the files: > > 10359_controls.html > 10359_modes.php > test_inner_10359.php > x359.bit > > ------------ x359.bit v1.9 from cvs --------------- > > After the following procedure > > 1) camvc, set on tab 5 horizontal to half, vertical to full -> > 1296x1920 > 2) set cam to triggered mode using > > http://10.0.0.9/parsedit.php?embed=0.1&title=External+trigger+controls&TRIG=4&TRIG_PERIOD=19200000&TRIG_DELAY&EARLY_TIMESTAMP=1&THIS_FRAME=@&TRIG_CONDITION=0&TRIG_OUT=0&SENSOR_REGS30=@ > > <http://10.0.0.9/parsedit.php?embed=0.1&title=External+trigger+controls&TRIG=4&TRIG_PERIOD=19200000&TRIG_DELAY&EARLY_TIMESTAMP=1&THIS_FRAME=@&TRIG_CONDITION=0&TRIG_OUT=0&SENSOR_REGS30=@> > > ** result 1 ** > 3) enable combining by pressing the button "Alternation mode with > buffering" and having "Combine into one frame" checked > http://10.0.0.9/359/10359_controls.html > > --> result: buffered frame is scrambled, buffered and unbuffered frame > flipping > > ** result 2 ** > 3) enable combining by pressing the button "Alternation mode" > --> result: no combined frame, I guess thats ok > > ** result 3 ** > 3) enable combining by using your previous script > http://10.0.0.9/359/10359_combining.php?x=1296&y=960&mode=on > <http://10.0.0.9/359/10359_combining.php?x=1296&y=960&mode=on> > <http://192.168.0.9/359/10359_combining.php?x=1296&y=960&mode=on > <http://192.168.0.9/359/10359_combining.php?x=1296&y=960&mode=on>> > > --> result: position and brightness of the combined frame is unstable > > ---------- x359.bit from your email 20091201 ------------ > > combining frames works fine for buffering A + B. > > ================================ > > conclusion: > > with the x359.bit from cvs I got the same problems like the ones I got > when I testet the "alternation mode with buffering" without combining. > Additionally the frame of sensor one and of sensor two are > interchanging. Contrary, the version with buffering of A+B worked > out of > the box. I had no problem at all with it. Unfortunately buffering > A+B is > not sufficient due to the limited bandwidth. > The question is: Does it make sense to keep the version which > buffers B > only? > I propose to move on to A+B/C+D version which improves stability and > bandwidth. > > Andreas > > _______________________________________________ > Support-list mailing list > [email protected] > <mailto:[email protected]> > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > > > > > ------------------------------------------------------------------------ > > /10359 board controls/ > Use sensors (J2,J3,J4) > Switch to channel : > Sensor test mode ON/OFF > > > Number of phase steps: > Channel 0 phase > Channel 1 phase > Channel 2 phase > > > SDRAM clock > Clock phase > > > Combine into one frame > Scale factor > Alternation mode with buffering: > > Alternation mode: > > > > Request line > > > > Firmware Version: > Current Channel: > Reg 0x02: > Reg 0x03h(pclk): > Reg 0x03l(sclk0): > Reg 0x05: > Reg 0x06: > Reg 0x07: > Reg 0x20: > Reg 0x44: > > > > > ------------------------------------------------------------------------ >
<<attachment: office.vcf>>
_______________________________________________ Support-list mailing list [email protected] http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
