Might be a long show but also get the output of netstat -m And netstat -in
-----Original Message----- From: Mojo Jojo [mailto:[EMAIL PROTECTED] Sent: Wednesday, September 21, 2005 11:47 AM To: [email protected] Subject: Re: [pfSense Support] Argg! My PfSense just died! This is what top says, if it's of any help: ############################################################## $ top last pid: 6598; load averages: 0.34, 0.29, 0.22 up 0+14:30:39 11:46:07 54 processes: 1 running, 53 sleeping Mem: 27M Active, 39M Inact, 35M Wired, 4992K Cache, 22M Buf, 9828K Free Swap: 256M Total, 256M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 6247 _pflogd 1 -58 0 1536K 1108K bpf 0:05 0.49% pflogd 6586 root 1 -8 10 11032K 9848K piperd 0:00 0.20% php 6598 root 1 139 10 2196K 1300K RUN 0:00 0.20% top 6597 root 1 8 10 1620K 1156K wait 0:00 0.20% sh 264 root 1 -58 0 6060K 3980K bpf 34:50 0.00% tcpdump 3390 root 1 -58 0 5528K 3456K bpf 6:42 0.00% tcpdump 470 root 1 76 0 1332K 768K select 3:17 0.00% syslogd 265 root 1 -8 0 1188K 604K piperd 1:50 0.00% logger 3391 root 1 -8 0 1188K 604K piperd 0:26 0.00% logger 263 _pflogd 1 -58 0 1536K 1036K bpf 0:08 0.00% pflogd 3388 _pflogd 1 -58 0 1536K 1056K bpf 0:04 0.00% pflogd 550 root 1 8 0 232K 104K nanslp 0:01 0.00% check_reload_status 539 root 1 8 0 1300K 840K nanslp 0:00 0.00% cron 3620 root 1 8 0 1620K 928K wait 0:00 0.00% sh 6248 root 1 -8 0 1188K 688K piperd 0:00 0.00% logger 121 root 1 76 0 1208K 664K select 0:00 0.00% usbd 5883 root 1 76 0 5580K 2088K select 0:00 0.00% sshd 555 root 1 5 0 1632K 920K ttyin 0:00 0.00% sh ################################################# ----- Original Message ----- From: "Scott Ullrich" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Wednesday, September 21, 2005 11:33 AM Subject: Re: [pfSense Support] Argg! My PfSense just died! top from a shell will tell you this. I have never ever seen a box just all of the sudden stop working. If a box blows up, it goes big time with kernel panics, etc. And even this I have not seen since being on crappy 5.X. 6.X of FreeBSD is looking mighty fine. Scott On 9/21/05, Mojo Jojo <[EMAIL PROTECTED]> wrote: > I meant, nothing plugged into the LAN NIC and nothing plugged into the OPT > 2 > NIC. > > Sorry about that. > > I am starting to wonder if this could be a RAM issue, as in, not enough of > it. > > Todd > > > ----- Original Message ----- > From: "Chris Buechler" <[EMAIL PROTECTED]> > To: <[email protected]> > Sent: Wednesday, September 21, 2005 9:19 AM > Subject: Re: [pfSense Support] Argg! My PfSense just died! > > > > Mojo Jojo wrote: > > > >> > >> Just some further info.. > >> > >> System died last night again after approx 6 hours of uptime. > >> > >> I could still get to the GUI, could still SSH to it but it would pass > >> any > >> traffic through to the OPT 2 (DMZ) interface. > >> > >> I attempted to run /etc/rc.bootup at the command line which restarted > >> Pf > >> fine. After the restart of Pf (not the whole computer) everything thing > >> was still in the same shape with no traffic passing through to the DMZ. > >> > >> The only thing that corrected this was a reboot which I initiated via > >> the > >> Pf GUI. > >> > >> Further info: > >> V. 0.84 > >> Running on a PIII 933 with 128mb of ram. I have 4 Linksys NICS > >> installed > >> on the PCI bus and one on the motherboard which I had disabled. > >> > >> Onboard NIC (disabled in BIOS) > >> Linksys NIC 1 > LAN > >> Linksys NIC 2 > WAN (static IP on a T1 with ascend T1 router on other > >> end) > >> Linksys NIC 3 > OPT 1 (DMZ where servers are) > >> Linksys NIC 4 > OPT2 (not in use at the moment) > >> > >> The PC is a DELL, Pf is running on a Hard Drive. > >> > >> I installed a fresh copy of 0.84, this is not an upgrade. > >> > >> All Linksys/Network Everywhere NICS are identical model NC100. > >> > >> I have 26 aliases setup, 46 rules on the WAN tab, 14 rules on the DMZ > >> tab > >> and none on the LAN or OPT 2. > >> > >> I have nothing plugged into the WAN NIC and nothing plugged into the > >> LAN > >> NIC at this time. > >> > > > > umm, above you say it stops passing traffic, here you say you only have > > one NIC plugged in? It can't pass traffic with only one NIC plugged in. > > system logs after it stops passing traffic if it happens again may prove > > very useful. > > -cmb > > > > --------------------------------------------------------------------- > > To unsubscribe, e-mail: [EMAIL PROTECTED] > > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
