My IRC/forum nick is hoba. > -----Ursprüngliche Nachricht----- > Von: Barry Kiesz [mailto:[EMAIL PROTECTED] > Gesendet: Montag, 7. November 2005 21:11 > An: support@pfsense.com > Betreff: RE: [pfSense Support] Boot issues with .90 and .92 > > > This what I have and was able to reproduce this on 2 wrap > boxes (same CF > card though). I popped the CF card that had a pre.90 image > on it and it > booted on both wrap boards. > > WRAP.1E v1.09 > 640 KB Base Memory > 130048 KB Extended Memory > 512MB Kinston CF card > pfSense-Embedded-0.92.img.bin.gz > C:\Wrap>physdiskwrite.exe > physdiskwrite v0.5 by Manuel Kasper <[EMAIL PROTECTED]> > > Could it be a format issue on my CF card? Not knowing a > whole lot about > these, I'm just grabbing at straws > > Thanks for any help.. > > > Barry > > P.S. Holger, What's you nic on the IRC channel?... 'Cause I > think you were > the one helping me out last week. > > > -----Original Message----- > > From: Holger Bauer [mailto:[EMAIL PROTECTED] > > Sent: Monday, November 07, 2005 1:56 PM > > To: support@pfsense.com > > Subject: AW: [pfSense Support] Boot issues with .90 and .92 > > > > I have been using all versions of pfsense at my wrap with 4 > > nics (3 on board, 1 atheros). I noticed random reboots on > > applying wlan settings with pre .90 versions. This stopped > > with .90 and never came back. Actually I have been running > > .90, .90a, .92 (which was pulled due some issues) and I'm > > pretesting 0.93 atm (which is the first release with the new > > freebsd6 release files). 0.93 runs pretty smooth and even got > > faster (webgui feels faster, +3 mbit throghput wan to lan). I > > can confirm the stability issues with wireless for pre .90 > > versions but I never had installationproblems or stability > > issues without using wireless. I'm running off from a 256 MB > > cf with the unmodified 128 MB image written to it. > > Just in case you didn't notice or haven't followed it, there > > is a tutorial for seting up the wrap at > > http://pfsense.com/index.php?id=36 .. I don't know if this is > > helping you to get further, but I know quite a lot of users > > from the forums or the irc-channel using wraps without > > issues, even with wireless nics (and I have 3 wrapsystems > > running 24/7 with real live conditions, 2 with wireless nics). > > If you still don't get it running please reply with bios > > versions. Maybe this only pops up with a special bios > > version? I have plenty of wraps to test with (beginning from > > 1D to 1E hardwarereleases and I'm about to order 10 more > > wraps tomorrow which should have latest hardwarerelease and > > bios versions when they arrive. > > > > If someone is reading this and has a working wrap install > > please reply with "it's working for me with pfsense 0.xx, > > wrap 1x, Bios 1.0x. Also add if you are using a wireless nic > > or not (which shouldn't prevent boot but it's nice to know;-) > > Maybe we'll find a matrix what systems are affected (if it's > > something like that and there really is a bug with it). > > > > > > Holger > > > > > -----Ursprüngliche Nachricht----- > > > Von: Barry Kiesz [mailto:[EMAIL PROTECTED] > > > Gesendet: Montag, 7. November 2005 18:30 > > > An: support@pfsense.com > > > Betreff: [pfSense Support] Boot issues with .90 and .92 > > > > > > > > > This is most likely a newbie issue, but here goes.. This is > > > actually a two > > > part question/issue! > > > > > > 1. For the past week I 've been trying to install a fresh > > > copy of Pfsense > > > onto my wrap board. I'm able to install and boot .88 > just fine. I > > > attempted to overwrite the image on on 512MB CF card with .90 > > > and first gave > > > the error messages (didn't save them) and ended on Boot > > > prompt command. I > > > attempted to install again after downloading a fresh copy off > > > of the mirrors > > > and then it would get to this, sit there for a while and > > then reboot: > > > > > > WRAP.1E v1.09 > > > > > > Wisp-Router.com > > > Your Full Time Professionals > > > > > > 640 KB Base Memory > > > 130048 KB Extended Memory > > > > > > 01F0 Master 848A SAMSUNG CF/ATA > > > Phys C/H/S 999/16/63 Log C/H/S 499/32/63 > > > - > > > > > > > > > > > > So then I took a little break and waited for .92 to come out > > > and now I get > > > this and it just hangs there > > > > > > WRAP.1E v1.09 > > > > > > Wisp-Router.com > > > Your Full Time Professionals > > > > > > 640 KB Base Memory > > > 130048 KB Extended Memory > > > > > > 01F0 Master 848A SAMSUNG CF/ATA > > > Phys C/H/S 999/16/63 Log C/H/S 499/32/63 > > > Copyright (c) 1992-2005 The FreeBSD Project. > > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, > > > 1993, 1994 > > > The Regents of the University of California. All > > > rights reserved. > > > FreeBSD 6.0-RELEASE #0: Fri Nov 4 02:53:05 UTC 2005 > > > > [EMAIL PROTECTED]:/usr/obj/usr/src/sys/pfSense_wrap.6 > > > > > > > > > Fatal trap 1: privileged instruction fault while in kernel mode > > > instruction pointer = 0x20:0xc086588c > > > stack pointer = 0x28:0xc0c20d20 > > > frame pointer = 0x28:0xc0c20d68 > > > code segment = base 0x0, limit 0xfffff, type 0x1b > > > = DPL 0, pres 1, def32 1, gran 1 > > > processor eflags = interrupt enabled, resume, IOPL = 0 > > > current process = 0 () > > > trap number = 1 > > > panic: privileged instruction fault > > > Uptime: 1s > > > > > > > > > > > > > > > #2 question and the reason for the upgrade. I've been having > > > DHCP issues > > > with pfsense. I've tried m0n0wall and don't seem to have any > > > issues. I > > > really need to use pfsense for 2 reasons. First the > > > intferface is great and > > > two, I have an Atheros chipset on wirless card. Once I get > > > this back on up > > > I'll pay more attention to the log files to see what my > > > problem is... As > > > I've tried different PCs throughout this process. > > > > > > > > > Any help would be appreciated!! > > > \ > > > > > > > > > Thanks, > > > > > > Barry > > > > > > > > > > > > > > > > > > --------------------------------------------------------------------- > > > To unsubscribe, e-mail: [EMAIL PROTECTED] > > > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > > > > > > ____________ > > Virus checked by G DATA AntiVirusKit > > > > > > > --------------------------------------------------------------------- > > To unsubscribe, e-mail: [EMAIL PROTECTED] > > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > >
____________ Virus checked by G DATA AntiVirusKit --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
