I've never tested the minipci slot of my soekris (I 'suppose' it works) and the card has been given to me as working.
Is there any debugging command I could use? Luciano # ifconfig ath0 ifconfig: interface ath0 does not exist # -----Messaggio originale----- Da: Scott Ullrich [mailto:[EMAIL PROTECTED] Inviato: domenica 18 dicembre 2005 20.05 A: [email protected] Oggetto: Re: [pfSense Support] Ver0.96.6,embedded : Atheros card not bound to driver I just tried the same image and it seems to be fine: # ifconfig ath0 ath0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::20b:6bff:fe34:aed0%ath0 prefixlen 64 scopeid 0x1 ether 00:0b:6b:34:ae:d0 media: IEEE 802.11 Wireless Ethernet autoselect mode 11b <hostap> status: associated ssid maconbacon channel 2 bssid 00:0b:6b:34:ae:d0 authmode WPA privacy MIXED deftxkey 3 TKIP 2:128-bit TKIP 3:128-bit txpowmax 40 protmode CTS -apbridge dtimperiod 1 bintval 100 Scott On 12/18/05, Luciano La Delfa <[EMAIL PROTECTED]> wrote: > Hi, > I've installed on my Soekris Net4801 the Atheros (Model Ag-621) wireless > minipci card. > It's not working and this is the message I get during boot. > > ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 11 at device 14.0 on pci0 > ath0: unable to attach hardware; HAL status 14 > device_attach: ath0 attach returned 6 > > > Regards, > Luciano > > > more dmesg.boot > > Copyright (c) 1992-2005 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 6.0-STABLE #0: Mon Dec 12 23:50:27 UTC 2005 > [EMAIL PROTECTED]:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class > CPU) > Origin = "Geode by NSC" Id = 0x540 Stepping = 0 > Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX> > real memory = 134217728 (128 MB) > avail memory = 121905152 (116 MB) > wlan: mac acl policy registered > ath_hal: 0.9.16.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, > DFS) > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > cpu0 on motherboard > pcib0: <Host to PCI bridge> pcibus 0 on motherboard > pci0: <PCI bus> on pcib0 > sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem > 0xa0000000-0xa000 > 0fff irq 10 at device 6.0 on pci0 > sis0: Silicon Revision: DP83816A > miibus0: <MII bus> on sis0 > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis0: Ethernet address: 00:00:24:c4:80:00 > sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem > 0xa0001000-0xa000 > 1fff irq 10 at device 7.0 on pci0 > sis1: Silicon Revision: DP83816A > miibus1: <MII bus> on sis1 > ukphy1: <Generic IEEE 802.3u media interface> on miibus1 > ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis1: Ethernet address: 00:00:24:c4:80:01 > sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem > 0xa0002000-0xa000 > 2fff irq 10 at device 8.0 on pci0 > sis2: Silicon Revision: DP83816A > miibus2: <MII bus> on sis2 > ukphy2: <Generic IEEE 802.3u media interface> on miibus2 > ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis2: Ethernet address: 00:00:24:c4:80:02 > ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 11 at device 14.0 on pci0 > ath0: unable to attach hardware; HAL status 14 > device_attach: ath0 attach returned 6 > Geode GPIO@ = 6100 > Geode Soekris net4801 comBIOS ver. 1.27 20041122 Copyright (C) 2000-2004 > isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on > pci0 > isa0: <ISA bus> on isab0 > pci0: <bridge> at device 18.1 (no driver attached) > atapci0: <National Geode SC1100 ATA33 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0 > x177,0x376,0xe000-0xe00f at device 18.2 on pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > Geode CBA@ 0x6000 > Geode rev: 06 03 > Timecounter "Geode" frequency 27000000 Hz quality 1000 > pci0: <bridge> at device 18.5 (no driver attached) > ohci0: <OHCI (generic) USB controller> mem 0xa0820000-0xa0820fff irq 5 at > device > 19.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 3 ports with 3 removable, self powered > pmtimer0 on isa0 > orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff on isa0 > ppc0: parallel port not found. > sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0 > sio0: type 16550A, console > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > Timecounters tick every 1.000 msec > Fast IPsec: Initialized Security Association Processing. > ad0: 122MB <SanDisk SDCFH-128 FhDA0145> at ata0-master PIO4 > GEOM_LABEL: Label for provider ad0a is ufs/pfSense. > GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg. > Trying to mount root from ufs:/dev/ufs/pfSense > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
