Well I can't really boot to do a dmesg -a but these are the boot
messages. Just to be clear. I basically installed to the Microdrive
from the LiceISO CD, then mounted the micro drive and replaced the
kernel.gz with the one from the Embeded image. The change to the
/etc/ file didn't seem to make any difference.
PC Engines WRAP.1C/1D/1E v1.08
640 KB Base Memory
130048 KB Extended Memory
01F0 Master 848A ST64022CF
Phys C/H/S 7936/16/63 Log C/H/S 992/128/63
PC Engines WRAP.1C/1D/1E v1.08
640 KB Base Memory
130048 KB Extended Memory
01F0 Master 848A ST64022CF
Phys C/H/S 7936/16/63 Log C/H/S 992/128/63
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-PRERELEASE #0: Thu Mar 2 22:07:36 UTC 2006
[EMAIL PROTECTED]:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (128 MB)
avail memory = 121913344 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x1000-0x10ff mem
0x80000000-0x80000fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:02:73:cc
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0x1400-0x14ff mem
0x80040000-0x80040fff irq 9 at device 15.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0d:b9:02:73:cd
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0x1800-0x18ff mem
0x80080000-0x80080fff irq 11 at device 16.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:0d:b9:02:73:ce
Geode GPIO@ = f400
Geode PC Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005
isab0: <PCI-ISA bridge> port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on
pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <multimedia, audio> at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80<clock_battery>
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
Trying to mount root from ufs:/dev/da0s1a
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:da0s1a
? List valid disk boot devices
<empty line> Abort manual input
mountroot>
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
